Geoffrey Vaartstra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Geoffrey Vaartstra has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Evelyn N. Wang
Massachusetts Institute of Technology
6 shared publications - Carlos Daniel Díaz-Marín
Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA, USA
3 shared publications - Jeffrey C. Grossman
Department of Materials Science and Engineering, Massachusetts Institute of Technology, 77 Massachusetts Ave, Cambridge, Massachusetts 02139, United States
2 shared publications - Youngsup Song
Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, United States
2 shared publications - Zhengmao Lu
École Polytechnique Fédérale de Lausanne (EPFL)
2 shared publications Amy I. H. Hrdina
Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139, United States
1 shared publication
Latest Publications
- 20 February 2023
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 23 (5) , 1888-1896
Capillary Transfer of Self-Assembled Colloidal Crystals
Colloidal self-assembly has attracted significant interest in numerous applications including optics, electrochemistry, thermofluidics, and biomolecule templating. To meet the requirements of these applications, numerous fabrication methods have been developed. However, these are limited to narrow ranges of feature sizes, are incompatible with many substrates, and/or have low scalability, significantly limiting the use of colloidal self-assembly. In this work, we study the capillary transfer of colloidal crystals and demonstrate that this approach overcomes these limitations. Enabled by capillary transfer, we fabricate 2D colloidal crystals with nano-to-micro feature sizes spanning 2 orders of magnitude and on typically challenging substrates including those that are hydrophobic, rough, curved, or structured with microchannels. We developed and systemically validated a capillary peeling model, elucidating the underlying transfer physics. Due to its high versatility, good quality, and simplicity, this approach can expand the possibilities of colloidal self-assembly and enhance the performance of applications using colloidal crystals.
- 20 February 2023
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 23 (5) , 1888-1896
Capillary Transfer of Self-Assembled Colloidal Crystals
Colloidal self-assembly has attracted significant interest in numerous applications including optics, electrochemistry, thermofluidics, and biomolecule templating. To meet the requirements of these applications, numerous fabrication methods have been developed. However, these are limited to narrow ranges of feature sizes, are incompatible with many substrates, and/or have low scalability, significantly limiting the use of colloidal self-assembly. In this work, we study the capillary transfer of colloidal crystals and demonstrate that this approach overcomes these limitations. Enabled by capillary transfer, we fabricate 2D colloidal crystals with nano-to-micro feature sizes spanning 2 orders of magnitude and on typically challenging substrates including those that are hydrophobic, rough, curved, or structured with microchannels. We developed and systemically validated a capillary peeling model, elucidating the underlying transfer physics. Due to its high versatility, good quality, and simplicity, this approach can expand the possibilities of colloidal self-assembly and enhance the performance of applications using colloidal crystals.
- Open Access
- 1 December 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (12) , 121701
Numerical validation of the dusty-gas model for binary diffusion in low aspect ratio capillaries
The dusty-gas model is an empirical formulation commonly used to describe gas flows in porous media. While experiments have validated the model for pores with high aspect ratios, a validation for near-unity aspect ratios is lacking. We used direct simulation Monte Carlo to evaluate the accuracy of the dusty-gas model for binary diffusion in low aspect ratio capillaries. Our results suggest that the dusty-gas model deviates from the Monte Carlo simulations by less than 3% for aspect ratios ≥ 1, thus supporting its suitability as a phenomenological model for transport in nanoporous structures in various applications such as heat transfer, catalysis, and water purification.
- 1 December 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (12) , 121701
Open AccessNumerical validation of the dusty-gas model for binary diffusion in low aspect ratio capillaries
The dusty-gas model is an empirical formulation commonly used to describe gas flows in porous media. While experiments have validated the model for pores with high aspect ratios, a validation for near-unity aspect ratios is lacking. We used direct simulation Monte Carlo to evaluate the accuracy of the dusty-gas model for binary diffusion in low aspect ratio capillaries. Our results suggest that the dusty-gas model deviates from the Monte Carlo simulations by less than 3% for aspect ratios ≥ 1, thus supporting its suitability as a phenomenological model for transport in nanoporous structures in various applications such as heat transfer, catalysis, and water purification.
- 21 October 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (43) , 12568-12576
Rational Fabrication of Nano-to-Microsphere Polycrystalline Opals Using Slope Self-Assembly
Self-assembly of artificial opals has garnered significant interest as a facile nanofabrication technique capable of producing highly ordered structures for optical, electrochemical, biomolecular, and thermal applications. In these applications, the optimum opal particle diameter can vary by several orders of magnitude because the properties of the resultant structures depend strongly on the feature size. However, current opal fabrication techniques only produce high-quality structures over a limited range of sphere sizes or require complex processes and equipment. In this work, the rational and simple fabrication of polycrystalline opals with diameters between 500 nm and 10 μm was demonstrated using slope self-assembly of colloids suspended in ethanol–water. The role of the various process parameters was elucidated through a scaling-based model that accurately captures the variations of opal substrate coverage for spheres of size 2 μm or smaller. For spheres of 10 μm and larger, capillary forces were shown to play a key role in the process dynamics. Based on these insights, millimeter-scale monolayered opals were successfully fabricated, while centimeter-scale opals were possible with sparse sphere stacking or small uncovered areas. These insights provide a guide for the simple and fast fabrication of opals that can be used as optical coatings, templates for high power density electrodes, molecule templates, and high-performance thermo-fluidic devices.
- 21 October 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (43) , 12568-12576
Rational Fabrication of Nano-to-Microsphere Polycrystalline Opals Using Slope Self-Assembly
Self-assembly of artificial opals has garnered significant interest as a facile nanofabrication technique capable of producing highly ordered structures for optical, electrochemical, biomolecular, and thermal applications. In these applications, the optimum opal particle diameter can vary by several orders of magnitude because the properties of the resultant structures depend strongly on the feature size. However, current opal fabrication techniques only produce high-quality structures over a limited range of sphere sizes or require complex processes and equipment. In this work, the rational and simple fabrication of polycrystalline opals with diameters between 500 nm and 10 μm was demonstrated using slope self-assembly of colloids suspended in ethanol–water. The role of the various process parameters was elucidated through a scaling-based model that accurately captures the variations of opal substrate coverage for spheres of size 2 μm or smaller. For spheres of 10 μm and larger, capillary forces were shown to play a key role in the process dynamics. Based on these insights, millimeter-scale monolayered opals were successfully fabricated, while centimeter-scale opals were possible with sparse sphere stacking or small uncovered areas. These insights provide a guide for the simple and fast fabrication of opals that can be used as optical coatings, templates for high power density electrodes, molecule templates, and high-performance thermo-fluidic devices.
- 20 September 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (19) , 8160-8165
Bottom-Up Synthesized All-Thermal-Catalyst Aerogels for Heat-Regenerative Air Filtration
Airborne particular matter (PM) pollution is an increasing global issue and alternative sources of filter fibers are now an area of significant focus. Compared with relatively mature hazardous gas treatments, state of the art high-efficiency PM filters still lack thermal decomposition ability for organic PM pollutants, such as soot from coal-fired power plants and waste-combustion incinerators, resulting in frequent replacement, high cost, and second-hand pollution. In this manuscript, we propose a bottom-up synthesis method to make the first all-thermal-catalyst air filter (ATCAF). Self-assembled from ∼50 nm diameter TiO2 fibers, ATCAF could not only capture the combustion-generated PM pollutants with >99.999% efficiency but also catalyze the complete decomposition of the as-captured hydrocarbon pollutants at high temperature. It has the potential of in situ eliminating the PM pollutants from burning of hydrocarbon materials leveraging the burning heat.
- 20 September 2021
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 21 (19) , 8160-8165
Bottom-Up Synthesized All-Thermal-Catalyst Aerogels for Heat-Regenerative Air Filtration
Airborne particular matter (PM) pollution is an increasing global issue and alternative sources of filter fibers are now an area of significant focus. Compared with relatively mature hazardous gas treatments, state of the art high-efficiency PM filters still lack thermal decomposition ability for organic PM pollutants, such as soot from coal-fired power plants and waste-combustion incinerators, resulting in frequent replacement, high cost, and second-hand pollution. In this manuscript, we propose a bottom-up synthesis method to make the first all-thermal-catalyst air filter (ATCAF). Self-assembled from ∼50 nm diameter TiO2 fibers, ATCAF could not only capture the combustion-generated PM pollutants with >99.999% efficiency but also catalyze the complete decomposition of the as-captured hydrocarbon pollutants at high temperature. It has the potential of in situ eliminating the PM pollutants from burning of hydrocarbon materials leveraging the burning heat.
- 8 March 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (10) , 12629-12635
Microtube Surfaces for the Simultaneous Enhancement of Efficiency and Critical Heat Flux during Pool Boiling
Boiling is an essential process in numerous applications including power plants, thermal management, water purification, and steam generation. Previous studies have shown that surfaces with microcavities or biphilic wettability can enhance the efficiency of boiling heat transfer, that is, the heat transfer coefficient (HTC). Surfaces with permeable structures such as micropillar arrays, in contrast, have shown significant enhancement of the critical heat flux (CHF). In this work, we investigated microtube structures, where a cavity is defined at the center of a pillar, as structural building blocks to enhance HTC and CHF simultaneously in a controllable manner. We demonstrated simultaneous CHF and HTC enhancements of up to 62 and 244%, respectively, compared to those of a smooth surface. The experimental data along with high-speed images elucidate the mechanism for simultaneous enhancement where bubble nucleation occurs in the microtube cavities for increased HTC and microlayer evaporation occurs around microtube sidewalls for increased CHF. Furthermore, we combined micropillars and microtubes to create surfaces that further increased CHF by achieving a path to separate nucleating bubbles and rewetting liquids. This work provides guidelines for the systematic surface design for boiling heat transfer enhancement and has important implications for understanding boiling heat transfer mechanisms.
- 8 March 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 13 (10) , 12629-12635
Microtube Surfaces for the Simultaneous Enhancement of Efficiency and Critical Heat Flux during Pool Boiling
Boiling is an essential process in numerous applications including power plants, thermal management, water purification, and steam generation. Previous studies have shown that surfaces with microcavities or biphilic wettability can enhance the efficiency of boiling heat transfer, that is, the heat transfer coefficient (HTC). Surfaces with permeable structures such as micropillar arrays, in contrast, have shown significant enhancement of the critical heat flux (CHF). In this work, we investigated microtube structures, where a cavity is defined at the center of a pillar, as structural building blocks to enhance HTC and CHF simultaneously in a controllable manner. We demonstrated simultaneous CHF and HTC enhancements of up to 62 and 244%, respectively, compared to those of a smooth surface. The experimental data along with high-speed images elucidate the mechanism for simultaneous enhancement where bubble nucleation occurs in the microtube cavities for increased HTC and microlayer evaporation occurs around microtube sidewalls for increased CHF. Furthermore, we combined micropillars and microtubes to create surfaces that further increased CHF by achieving a path to separate nucleating bubbles and rewetting liquids. This work provides guidelines for the systematic surface design for boiling heat transfer enhancement and has important implications for understanding boiling heat transfer mechanisms.
- Open Access
- 5 October 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (13) , 130901
Capillary-fed, thin film evaporation devices
Evaporation plays a critical role in a range of technologies that power and sustain our society. Wicks are widely used as passive, capillary-fed evaporators, attracting much interest since these devices are highly efficient, compact, and thermally stable. While wick-based evaporators can be further improved with advanced materials and fabrication techniques, modeling of heat and mass transport at the device level is vital for guiding these innovations. In this perspective, we present the design and optimization of capillary-fed, thin film evaporation devices through a heat and mass transfer lens. This modeling framework can guide future research into materials innovations, fabrication of novel architectures, and systems design/optimization for next generation, high-performance wick-based evaporators. Furthermore, we describe specific challenges and opportunities for the fundamental understanding of evaporation physics. Finally, we apply our modeling framework to the analysis of two important applications—solar vapor generation and electronics cooling devices.
- 5 October 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (13) , 130901
Open AccessCapillary-fed, thin film evaporation devices
Evaporation plays a critical role in a range of technologies that power and sustain our society. Wicks are widely used as passive, capillary-fed evaporators, attracting much interest since these devices are highly efficient, compact, and thermally stable. While wick-based evaporators can be further improved with advanced materials and fabrication techniques, modeling of heat and mass transport at the device level is vital for guiding these innovations. In this perspective, we present the design and optimization of capillary-fed, thin film evaporation devices through a heat and mass transfer lens. This modeling framework can guide future research into materials innovations, fabrication of novel architectures, and systems design/optimization for next generation, high-performance wick-based evaporators. Furthermore, we describe specific challenges and opportunities for the fundamental understanding of evaporation physics. Finally, we apply our modeling framework to the analysis of two important applications—solar vapor generation and electronics cooling devices.