Dominic Parsons
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dominic Parsons has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Hao Yuan
Department of Mechanical Engineering, University of Bath, Bath BA2 7AY, UK
2 shared publications Harsh Goyal
2 shared publicationsPeter Jones
2 shared publications- Sam Akehurst
University of Bath
2 shared publications - Stefania Esposito
RWTH Aachen University
2 shared publications - Abdullah Umair Bajwa
Texas A&M University, College Station, TX, USA
1 shared publication
Latest Publications
- 18 March 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (10) , 1-12
Improving the Predictive Capability of Empirical Heat Transfer Correlations for Hydrogen Internal Combustion Engines
Hydrogen internal combustion is widely considered a viable technology to achieve near-zero tailpipe CO2 and NOx emissions for difficult-to-electrify applications due to the maturity of ICE technology and production facilities. 1D/0D modelling is a valuable tool for engine development due to its relatively low computational requirements, but hydrogen combustion models still require further development. A large factor is gas-to-wall heat transfer, which is higher for hydrogen combustion due to higher flame temperatures and shorter quenching distance. For accurate prediction of in-cylinder temperatures, and therefore combustion rates and knock propensity, a well calibrated heat transfer model is essential. This paper evaluates existing heat transfer models against previously published experimental cylinder pressure and heat flux data from a Cooperative Fuel Research (CFR) engine with hydrogen Port Fuel Injection (PFI). A new heat transfer correlation is developed, utilising a new fluid properties correlation to better represent the change in viscosity and conductivity with changing hydrogen concentration. Recent developments in 0D turbulence models improve the characteristic velocity calculation, which is augmented with a combustion term. This model is tested against a second dataset from the CFR engine with lambda from 1.0 - 4.0 and compression ratios of 9 - 13, showing improved performance versus previously published models. Whilst the new model provides more consistent results during combustion for variations in lambda and compression ratio, it requires improvement in its prediction of heat loss during expansion, and further validation at higher engine speeds and different engine configurations.
- 18 March 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (10) , 1-12
Improving the Predictive Capability of Empirical Heat Transfer Correlations for Hydrogen Internal Combustion Engines
Hydrogen internal combustion is widely considered a viable technology to achieve near-zero tailpipe CO2 and NOx emissions for difficult-to-electrify applications due to the maturity of ICE technology and production facilities. 1D/0D modelling is a valuable tool for engine development due to its relatively low computational requirements, but hydrogen combustion models still require further development. A large factor is gas-to-wall heat transfer, which is higher for hydrogen combustion due to higher flame temperatures and shorter quenching distance. For accurate prediction of in-cylinder temperatures, and therefore combustion rates and knock propensity, a well calibrated heat transfer model is essential. This paper evaluates existing heat transfer models against previously published experimental cylinder pressure and heat flux data from a Cooperative Fuel Research (CFR) engine with hydrogen Port Fuel Injection (PFI). A new heat transfer correlation is developed, utilising a new fluid properties correlation to better represent the change in viscosity and conductivity with changing hydrogen concentration. Recent developments in 0D turbulence models improve the characteristic velocity calculation, which is augmented with a combustion term. This model is tested against a second dataset from the CFR engine with lambda from 1.0 - 4.0 and compression ratios of 9 - 13, showing improved performance versus previously published models. Whilst the new model provides more consistent results during combustion for variations in lambda and compression ratio, it requires improvement in its prediction of heat loss during expansion, and further validation at higher engine speeds and different engine configurations.
- Top Cited PapersOpen Access
- 4 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 86, 1179-1194
Design trends and challenges in hydrogen direct injection (H2DI) internal combustion engines – A review
- 4 September 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 86, 1179-1194
Top Cited PapersOpen AccessDesign trends and challenges in hydrogen direct injection (H2DI) internal combustion engines – A review
- 11 October 2020
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 22 (9) , 2819-2829
A comparative study into the effects of pre and post catalyst exhaust gas recirculation on the onset of knock
Exhaust gas recirculation (EGR) is proven as a valuable technology for controlling knock whilst maintaining lambda one operation, and is also capable of providing efficiency gains at low load. Despite this few studies in the literature address the question of EGR composition effects, namely whether the EGR gas is sourced from before or after the catalyst, and this remains an area which is often overlooked whilst investigating EGR performance. This paper demonstrates a novel method combining experiment air-path emulation and in-depth data processes to compare the effect of EGR catalysis on the angle of knock onset in a 1L GDI engine. Since initial temperature and pressure have a significant impact on knocking behaviour, an artificial boosting rig replaced the turbomachinery. This enabled fine control over the engine boundary conditions to ensure parity between the catalysed and un-catalysed cases. To overcome the difficulty of comparing stochastic phenomena in an inherently variable dataset, a pairing method was combined with Shahlari and Ghandhi’s angle of knock onset determination method to assess the effects of EGR composition on knock onset for EGR rates ranging from 9% to 18%. The air path emulation system stabilised the engine combustion to provide a suitably rich dataset for analysing knock using the pairing method. Catalysed EGR improved the mean knock onset angle by 0.55 CAD, but due to the inherent variability in cylinder pressure data this only equated to a 58.3% chance of a later knock onset angle for catalysed EGR in any given pair of comparative cycles.
- 11 October 2020
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 22 (9) , 2819-2829
A comparative study into the effects of pre and post catalyst exhaust gas recirculation on the onset of knock
Exhaust gas recirculation (EGR) is proven as a valuable technology for controlling knock whilst maintaining lambda one operation, and is also capable of providing efficiency gains at low load. Despite this few studies in the literature address the question of EGR composition effects, namely whether the EGR gas is sourced from before or after the catalyst, and this remains an area which is often overlooked whilst investigating EGR performance. This paper demonstrates a novel method combining experiment air-path emulation and in-depth data processes to compare the effect of EGR catalysis on the angle of knock onset in a 1L GDI engine. Since initial temperature and pressure have a significant impact on knocking behaviour, an artificial boosting rig replaced the turbomachinery. This enabled fine control over the engine boundary conditions to ensure parity between the catalysed and un-catalysed cases. To overcome the difficulty of comparing stochastic phenomena in an inherently variable dataset, a pairing method was combined with Shahlari and Ghandhi’s angle of knock onset determination method to assess the effects of EGR composition on knock onset for EGR rates ranging from 9% to 18%. The air path emulation system stabilised the engine combustion to provide a suitably rich dataset for analysing knock using the pairing method. Catalysed EGR improved the mean knock onset angle by 0.55 CAD, but due to the inherent variability in cylinder pressure data this only equated to a 58.3% chance of a later knock onset angle for catalysed EGR in any given pair of comparative cycles.