Zhi-Yong Zhang
Research Subjects
Zhi-Yong Zhang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Jun Zhao
Shenyang Research Institute of Foundry Co., Ltd. CAM, Shenyang, China
3 shared publicationsKun Shi
Shenyang Research Institute of Foundry Co., Ltd. CAM, Shenyang, China
3 shared publications- Pei Liu
College of Materials Science and Engineering Henan University of Science and Technology Luoyang 471023 China
2 shared publications Shi-Bing Liu
Shenyang Research Institute of Foundry Co., Ltd. CAM, Shenyang, China
2 shared publicationsAi-Qin Wang
College of Materials Science and Engineering, Henan University of Science and Technology, Luoyang, Henan, China
1 shared publicationAiqin Wang
College of Materials Science and Engineering, Henan University of Science and Technology, Luoyang, China
1 shared publication
Latest Publications
- 28 May 2026
- Published by Springer Nature in China Foundry
- Vol. 23 (3) , 377-384
Regulating creep behavior via dynamic in-situ precipitation of Ti3AlC phase in Ti45Al8Nb-0.6C alloy
- 28 May 2026
- Published by Springer Nature in China Foundry
- Vol. 23 (3) , 377-384
Regulating creep behavior via dynamic in-situ precipitation of Ti3AlC phase in Ti45Al8Nb-0.6C alloy
- 20 June 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (2) , 1558-1564
The Effect of Cryogenic-Temperature Rolling on the Microstructure and Mechanical Properties of TA18 Titanium Alloy
- 20 June 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (2) , 1558-1564
The Effect of Cryogenic-Temperature Rolling on the Microstructure and Mechanical Properties of TA18 Titanium Alloy
- 10 January 2024
- Published by Springer Nature in China Foundry
- Vol. 21 (2) , 168-174
Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method
- 10 January 2024
- Published by Springer Nature in China Foundry
- Vol. 21 (2) , 168-174
Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method
- Open Access
- 12 October 2020
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 321, 11057
Study on Microstructure and Mechanical Properties of Powder Metallurgy TA15 Titanium Alloy
TA15 pre-alloyed powder chosen in this paper is made by plasma rotating electrode method. The powders were used to prepare fully dense TA15 alloy ingots by the means of hot isostatic pressing(HIP) forming technology. The optimum parameter of the HIP process is 900°C /120MPa/3h. After the process of hot isostatic pressing, the powders were pressed into a fully dense ingot. An optital microscope was used to observe the microstructure of the ingot specimen and its formation mechanism was analysized. The microstructure of the TA15 alloy prepared by hot isostatic pressing of pre-alloyed powder is composed of fine α-equiaxed grains along lamellar colony boundaries. The mechanical properties exceed that of the casting level, which is close to the forging level. A typical TA15 alloy component was finally produced by HIP-PM process.
- 12 October 2020
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 321, 11057
Open AccessStudy on Microstructure and Mechanical Properties of Powder Metallurgy TA15 Titanium Alloy
TA15 pre-alloyed powder chosen in this paper is made by plasma rotating electrode method. The powders were used to prepare fully dense TA15 alloy ingots by the means of hot isostatic pressing(HIP) forming technology. The optimum parameter of the HIP process is 900°C /120MPa/3h. After the process of hot isostatic pressing, the powders were pressed into a fully dense ingot. An optital microscope was used to observe the microstructure of the ingot specimen and its formation mechanism was analysized. The microstructure of the TA15 alloy prepared by hot isostatic pressing of pre-alloyed powder is composed of fine α-equiaxed grains along lamellar colony boundaries. The mechanical properties exceed that of the casting level, which is close to the forging level. A typical TA15 alloy component was finally produced by HIP-PM process.
- Open Access
- 1 January 2020
- Published by Springer Nature in China Foundry
- Vol. 17 (1) , 29-34
Elimination of misrun and gas hole defects of investment casting TiAl alloy turbocharger based on numerical simulation and experimental study
- 1 January 2020
- Published by Springer Nature in China Foundry
- Vol. 17 (1) , 29-34
Open AccessElimination of misrun and gas hole defects of investment casting TiAl alloy turbocharger based on numerical simulation and experimental study