MRMatteo Repetto

Matteo Repetto

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Matteo Repetto has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Turbocompound Power Unit Modelling for a Supercapacitor-Based Series Hybrid Vehicle Application

    by Matteo Repetto, Massimiliano Passalacqua, Luis Vaccaro, Mario Marchesoni, Alessandro Pini Prato

    In this paper, starting from the measurements available for a 2000 cm3 turbocharged diesel engine, an analytical model of the turbocharger is proposed and validated. The model is then used to extrapolate the efficiency of a power unit with a diesel engine combined with a turbocompound system. The obtained efficiency map is used to evaluate the fuel economy of a supercapacitor-based series hybrid vehicle equipped with the turbocompound power unit. The turbocompound model, in accordance with the studies available in the technical literature, shows that the advantages (in terms of efficiency increase) are significant at high loads. For this reason, turbocompound introduction allows a significant efficiency improvement in a series hybrid vehicle, where the engine always works at high-load. The fuel economy of the proposed vehicle is compared with other hybrid and conventional vehicle configurations.


  • Open Access

    Supercapacitor Storage Sizing Analysis for a Series Hybrid Vehicle

    by Massimiliano Passalacqua, Mauro Carpita, Serge Gavin, Mario Marchesoni, Matteo Repetto, Luis Vaccaro, Sébastien Wasterlain

    The increasing interest in Hybrid Electric Vehicles led to the study of new powertrain structures. In particular, it was demonstrated in the technical literature how series architecture can be more efficient, compared to parallel one, if supercapacitors are used as storage system. Since supercapacitors are characterized by high efficiency and high power density, but have low specific energy, storage sizing is a critical point with this technology. In this study, a detailed analysis on the effect of supercapacitor storage sizing on series architecture was carried out. In particular, in series architecture, supercapacitor storage sizing influences both engine number of starts and the energy that can be stored during regenerative braking. The first aspect affects the comfort, whereas the second aspect directly influences powertrain efficiency. Vehicle model and Energy Management System were studied and simulations were carried out for different storage energy, in order to define the optimal sizing.


  • Open Access

    Electrical-Loss Analysis of Power-Split Hybrid Electric Vehicles

    by Andrea Bonfiglio, Damiano Lanzarotto, Mario Marchesoni, Massimiliano Passalacqua, Renato Procopio, Matteo Repetto

    The growing development of hybrid electric vehicles (HEVs) has seen the spread of architectures with transmission based on planetary gear train, realized thanks to two electric machines. This architecture, by continuously regulating the transmission ratio, allows the internal combustion engine (ICE) to work in optimal conditions. On the one hand, the average ICE efficiency is increased thanks to better loading situations, while, on the other hand, electrical losses are introduced due to the power circulation between the two electrical machines mentioned above. The aim of this study is then to accurately evaluate electrical losses and the average ICE efficiency in various operating conditions and over different road missions. The models used in this study are presented for both the Continuously Variable Transmission (CVT) architecture and the Discontinuously Variable Transmission (DVT) architecture. In addition, efficiency maps of the main components are shown. Finally, the simulation results are presented to point out strengths and weaknesses of the CVT architecture.


  • Open Access

    Advantages of Using Supercapacitors and Silicon Carbide on Hybrid Vehicle Series Architecture

    by Massimiliano Passalacqua, Damiano Lanzarotto, Matteo Repetto, Mario Marchesoni

    In recent years enormous growth has taken place in the hybrid vehicle sector; parallel architecture is the most widespread configuration regarding medium size cars. At the same time, storage systems and power electronics have experienced some important innovations. The development of supercapacitors has permitted management of high power with elevated efficiency. Moreover, the availability on the market of silicon carbide components has allowed a significant reduction of power electronic losses. These improvements may challenge the hybrid architecture used in medium size cars nowadays. On one hand, series architecture would relevantly benefit from an electric powertrain efficiency increase, on the other hand, these innovations would generate low benefits in parallel architectures. The aim of this paper is to evaluate electric component average efficiency over different road missions, in order to estimate fuel economy over various working conditions and finally to establish which hybrid configuration is most efficient in vehicle applications.


  • Simulation Model of a Passive Decay Heat Removal System for Lead-Cooled Fast Reactors

    by Lorenzo Damiani, Alessandro Pini Prato

    The generation IV lead cooled fast reactors are of particular interest for the Italian research: several influential companies (Ansaldo Nucleare, ENEA) are involved in these important European R&D projects. At present, one significant European project in progress is lead cooled European advanced demonstrator reactor (LEADER) which includes, among its goals, the construction of a lead-cooled fast reactor demonstrator, advanced lead fast reactor European demonstrator (ALFRED). The demonstrator has to include technical solutions that simplify the construction phase and assure full safety in operation; according to the latest guidelines, ALFRED final configuration will be characterized by a secondary loop providing bayonet-tube steam generators. The authors have addressed the issue of bayonet-tube steam generators proposing the external boiling bayonet steam generator (EBBSG) system, in which the reaction heat is extracted from the lead by means of coolant under vapor phase. This is possible thanks to an external feed-water boiling, based on the known Loeffler scheme, coupled to the bayonet tube concept. In the present paper, the authors propose a decay heat removal (DHR) system to match the EBBSG scheme. The DHR system is fully passive, exploiting natural circulation phenomena. The performance of the proposed DHR system is investigated through a Matlab-Simulink model. The results are satisfactory since, according to the simulations, the proposed DHR system is able to keep the primary coolant temperature within a safety range for a sufficient time, avoiding the lead freezing or over-heating.