RRRyszard Rekucki

Ryszard Rekucki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ryszard Rekucki has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical prognosis of the dynamic response of the steel rectangular slab under the explosive load

    by Sławomir Onopiuk, Adam Stolarski, Ryszard Rekucki

    The paper presents the methodology for determination the numerical prognosis of the dynamic response of the rectangular steel slab subjected to an explosive load, aimed at thorough preparation of experimental tests. In the presented work, in order to fully describe the parameters of the shock wave impact on the steel slab, an appropriate combination of formulas known in the literature was used. In order to describe the dynamic behavior of the rectangular steel slab, the resources of the ABAQUS computing software were used. The Johnson–Cook constitutive model was used to describe the dynamic behavior of the structural material. An explicit procedure has been used to solve the equations of motion for the slab. The parameters of the shock wave from the explosion of the TNT charge with the assumed mass and the distance of its location from the slab were determined. As a result of the numerical analysis, the results of changes in displacement and acceleration in time were presented, indicating the nature of the very intense and fast-varying dynamic behavior of the slab. Conclusions were also formulated regarding the requirements for the selection of parameters of the sensors recording both the function of real explosion pressure in time and the function of acceleration in time of the slab model during experimental tests.

  • Open Access

    Analysis of the Influence of Silty Sands Moisture Content and Impact Velocity in SHPB Testing on Their Compactability and Change in Granulometric Composition

    by Kamil Sobczyk, Ryszard Chmielewski, Leopold Kruszka, Ryszard Rekucki

    This paper presents the results of a test cycle of two types of silty sand (siSa) with different contents of fine fractions. Fine fractions are understood as soil grains with a grain diameter of less than 63 µm (as the sum of silt and clay fractions). The soils tested had a content of fine fractions of fSi+Cl,1 = 15.14% and fSi+Cl,2 = 20.48%, respectively, before the study. Changes in the content of these fractions after the experiments were analyzed. These experiments consisted of dynamic bar projectile impact loading, and a split Hopkinson pressure bar (SHPB) test stand was used in the study. Changes in the granulometric composition of the silty sands studied were carried out in a laser particle size analyzer, allowing measurement of fractional content in the grain size range from 0.01 µm to 3500 µm. As a result, a summary of changes in soil grain size curves in the range of fine fractions was compiled. Repeated trends were observed in the changes in the granulometric composition of the soil samples as a function of the moisture content of the soil sample (w1 = 0%, w2 = 5%, w3 = 10%, and w4 = 15%) and the impact velocity of the loading bar projectile for SHPB pneumatic launcher pressures (p1 = 1.2 bar → v1 = 12.76 m/s, p2 = 1.8 bar → v2 = 17.69 m/s and p3 = 2.4 bar → v3 = 21.32 m/s). The influence of the initial moisture content of the investigated soil on the value of the optimum moisture content obtained during its dynamic compaction was discussed. The trend in the behavior of the change in the granulometric composition of the tested samples was determined, taking the value of the initial moisture content of the soil in relation to the optimum moisture content of the reference sample as a reference. The largest percentage change in granulometric composition through an increase in the value of the silt and clay fraction relative to the reference sample fSi+Cl for both types of silty sand tested occurs for the same moisture content variant w2 = 5%–for soil fSi+Cl,1 = 15.14% there is an increase in the fine fraction of 11.08% and for soil fSi+Cl,2 = 20.48% there is an increase in the fine fraction of 15.17%. In general, it can be seen that more silty soil is more strongly susceptible to the phenomenon of grain crushing for moisture content w1 = 0% and w2 = 5% less than its optimum moisture content wopt,1 = 8.70%. In contrast, less silty soil is more susceptible to the phenomenon of grain crushing for moisture contents w3 = 10% and w4 = 15% greater than its optimum moisture content wopt,2 = 9.20%. The presented dynamic physical phenomenon of soil behavior is crucial during explosive and impact impacts on structures made of soil, e.g., as ground protection layers.


  • Open Access

    Preparation of the non-cohesive soil sample and calibration of the pneumatical launcher in the dynamic soil test SHPB

    by Kamil Sobczyk, Leopold Kruszka, Michał GRĄZKA, Ryszard Chmielewski, Ryszard Rekucki

    The paper analyzes the problem of initial compaction of a non-cohesive soil sample on the example of dry silty sand samples. Two different compaction methodologies were used: I) dynamic compaction - using split Hopkinson pressure bar and II) vibration compaction - using a vibrating shaker. A better result of the compaction process was obtained for dynamic compaction with an initial pressure value of 0.5 bar (small difference in the result - both methods obtained comparable results). The paper also includes a numerical analysis of the calibration of the pneumatic launcher in the Matlab environment on the basis of the system of difference equations. The calibration process was carried out in the initial pressure range from 0.5 to 3.0 bar for three different variants of the bar-projectile length: 100 mm, 200 mm and 250 mm and compared with the experimental analysis - the results were consistent.


  • Open Access

    Strength Characterization of Soils’ Properties at High Strain Rates Using the Hopkinson Technique—A Review of Experimental Testing

    by Kamil Sobczyk, Ryszard Chmielewski, Leopold Kruszka, Ryszard Rekucki

    The paper presents a review of crucial experiments and the latest publications, presenting the previous and current trends in experimental research in 2018–2021 in the area of soil dynamic interaction based on the Hopkinson bar technique. A review of investigated experimental test stands was made, in particular, cohesive and non-cohesive soil specimens prepared with different dimensions and densities. From this study, it can be concluded that the dynamic response of the soil depends on many factors, e.g., density, cohesion, moisture and grain structure of the soil specimen. There is still a noticeable interest in SHPB experiments performed in both 1D and 3D versions under modified conditions (frozen/heated soil specimen, different degree of water saturation content of the soil sample) in a wide range of strain rates 102–104 s−1, which is a large field for further research. The need to learn about the characteristics of various types of soil (both cohesive and non-cohesive) for the selection of structural design solutions for the protection elements of critical infrastructure was emphasized.


  • Open Access

    Performance characteristics of Hopkinson’s set-up pneumatic launcher

    by Kamil Sobczyk, Leopold Kruszka, Ryszard Chmielewski, Ryszard Rekucki

    The paper presents a performance characteristics of a pneumatic launcher, which is an important element of the split Hopkinson bar set-up (SHPB) at the Department of Military Engineering and Infrastructure (the Military University of Technology in Warsaw) for the purpose of dynamic strength tests of construction materials. The process of experimental calibration of the launcher for selected loading bar-projectiles is shown. Two types of compression during direct impact tests were also used simultaneously to investigate the behaviour of metallic samples with the use of this launcher as well as the Hopkinson measuring bar: the first — a short cylindrical sample, including a miniature (small diameter) sample, and the second — a long cylindrical sample (Taylor test). The relationships describing the stress and strain state as a function of strain rate for the first type of the experiment and engineering empirical formulas for the second type of the research were given.


  • Open Access

    Experimental Investigation of Dynamic Behavior of Silty Sand

    by Ryszard Chmielewski, Leopold Kruszka, Ryszard Rekucki, Kamil Sobczyk

    The paper includes experimental research using the Split Hopkinson Pressure Bar to determine dynamic compression curves and strength dynamic parameters to depend on the strain rate and moisture for silty sand soil samples. Those experiments are oedometric type based in a rigid confining cylinder. Samples of silty sand with fine a fraction content were taken for the study. To ensure sufficiently uniaxial strain of the tested material, the soil samples were placed in properly prepared casings made of duralumin for the needs of the tests. Thanks to the use of measuring strain gauges on the initiating and transmitting bars, as well as the casing, the nature of the loading pulse was obtained, which was then subjected to the process of filtration and data processing to obtain the nature of the incident, reflected and transmitted wave. During the above dynamic experiments with the representative of silty sand soils, it was observed that its dynamic compaction at a high strain rate is different than in the case of the Proctor test. This is due to higher compaction energy, which additionally changes the grain size by destroying the grains in the structure. The paper presents the results of particle size distribution analysis for two different types of soil samples - this type of analysis is unique. Hence experiments should be further continued for such soils with different granulations and various moisture using, for example, Hopkinson measuring bar technique to confirm for other silty sand soils that are often subgrade of various engineering objects.


  • Open Access

    SELECTED TECHNICAL AND LEGAL ASPECTS OF THE PNEUMATIC LAUNCHER OPERATION FOR HOPKINSON MEASURING BARS SET

    by Kamil Sobczyk, Leopold Kruszka, Ryszard Chmielewski, Ryszard Rekucki

    The paper presents selected technical and legal areas of the exploitation of a pneumatic launcher as an essential part of the mechanical test stand of the split Hopkinson bar for testing the dynamic properties of construction materials. The process of impact loading of the tested material sample is carried out by means of a loading bar-projectile fired from this launcher. The concept of the first stage of the modernization of the pneumatic launcher used at the Institute of Civil Engineering of the Military University of Technology (MUT) for over 20 years was discussed in order to facilitate the performance of physical experiments. The formal and legal requirements for the design, construction and usage of a test stand with a pneumatic launcher in a laboratory room are presented.