YNYoshitake Nishi

Yoshitake Nishi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yoshitake Nishi has a total of 77 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Novel Treatment of 3D-Printed Short-Carbon-Fiber-Reinforced Polyamide (3D-SCFRPA66) Using Homogeneous Low-Potential Electron Beam Irradiation (HLEBI) and Ductility Enhancement

    by Eiichi Miura, Helmut Takahiro Uchida, Taisuke Okazaki, Kohei Sagawa, Michael C. Faudree, Michelle Salvia, Hideki Kimura, Yoshitake Nishi

    In short-carbon-fiber-reinforced polyamide 66 articles shaped by 3D printing (3D-SCFRPA66), the interfaces between printed layers are often susceptible to damage, and the composite is excessively brittle. Therefore, a novel treatment for 3D-printed short-carbon-fiber-reinforced polyamide (3D-SCFRPA66) using homogeneous low-potential electron beam irradiation (HLEBI) to enhance tensile properties was investigated. In 3D-SCFRPA66 samples, ductility was measured based on the following parameters: strain at tensile strength (corresponding to homogeneous deformation) (εts) and resistance energy to homogeneous deformation, a measure of toughness (Ehd), which were both substantially increased. An HLEBI dose of 43.2 kGy at an acceleration potential of 210 kV for the finished 3D-SCFRPA66 samples increased the εts and Ehd values from 0.031 and 1.20 MPa·m for the untreated samples to 0.270 and 6.05 MPa·m for the treated samples, increases of 771% and 504%, respectively. Higher HLEBI doses of 86, 129, or 215 kGy also increased the εts and Ehd values to lesser degrees. Electron spin resonance (ESR) data in the literature show that HLEBI creates dangling bonds in Nylon 6. Since PA66 and Nylon 6 are constructed of C, N, and O and have similar molecular structures, HLEBI apparently severs the (-C-N-) bonds in the backbone of PA66, which have the lowest bond-dissociation energy (BDE) of ~326 to 335 kJ mol−1. This shortens the PA66 chains for higher ductility. In addition, for Nylon 6, X-ray photoelectron spectroscopy (XPS) data in the literature show that HLEBI reduces the N peak while increasing the C peak, indicating the occurrence of shortening chains via dangling bond formation accompanied by increases in crosslinking with carbon bonds. However, caution is advised, since HLEBI was found to decrease the tensile strength (σts) and initial elasticity ([dσ/dε]i) of 3D-SCFRPA66. This tradeoff can possibly allow the HLEBI dose to be adjusted for the desired ductility and strength while minimizing energy consumption.


  • Open Access

    A New Double-Step Process of Shortening Fibers without Change in Molding Equipment Followed by Electron Beam to Strengthen Short Glass Fiber Reinforced Polyester BMC

    by Michael C. Faudree, Yoshitake Nishi

    It is vital to maximize the safety of outdoor constructions, airplanes, and space vehicles by protecting against the impact of airborne debris from increasing winds due to climate change, or from bird strikes or micrometeoroids. In a widely-used compression-molded short glass fiber polyester bulk-molded compound (SGFRP-BMC) with 55% wt. CaCO3 filler, the center of the mother panel has lower impact strength than the outer sections with solidification texture angles and short glass fiber (SGF) orientations being random from 0 to 90 degrees. Therefore, a new double-step process of: (1) reducing commercial fiber length without change in molding equipment; followed by a (2) 0.86 MGy dose of homogeneous low-voltage electron beam irradiation (HLEBI) to both sides of the finished samples requiring no chemicals or additives, which is shown to increase the Charpy impact value (auc) about 50% from 6.26 to 9.59 kJm−2 at median-accumulative probability of fracture, Pf = 0.500. Shortening the SGFs results in higher fiber spacing density, Sf, as the thermal compressive stress site proliferation by action of the CTE difference between the matrix and SGF while the composite cools and shrinks. To boost impact strength further, HLEBI provides additional nano-compressive stresses by generating dangling bonds (DBs) creating repulsive forces while increasing SGF/matrix adhesion. Increased internal cracking apparently occurs, raising the auc.


  • Open Access

    Increasing Bending Strength of Polycarbonate Reinforced by Carbon Fiber Irradiated by Electron Beam

    by Yoshitake Nishi, Naruya Tsuyuki, Helmut Takahiro Uchida, Michael C. Faudree, Kouhei Sagawa, Masae Kanda, Yoshihito Matsumura, Michelle Salvia, Hideki Kimura

    In an interlayered carbon fiber-reinforced polycarbonate polymer (CFRPC) composite composed of three sized of CF plies, alternating between four PC sheets, designated [PC]4[CF]3, and a new process of activating CF cross-weave cloth plies directly on both sides with homogeneous low-energy electron beam irradiation (HLEBI) before lamination assembly and hot pressing at 6.0 MPa and 537 K for 8 min was produced. Experimental results show that a dose of 215 kGy of HLEBI raised the bending strength, σb, at each experimental accumulative probability, Pa, with the σb at a median Pa of 0.50, increasing by 25% over that of the untreated sample. Three-parameter Weibull analysis showed that when quality can be controlled, a dose of 215 kGy of HLEBI can raise the statistically lowest bending strength, σs, at Pa = 0 (94.3 Mpa), with a high correlation coefficient. This is because, although it had a higher bending strength than that in the other experimental conditions, the weakest sample of the 215 kGy data set had a much lower σb value than that of the others. Electron spin resonance (ESR) of the CF showed that naturally occurring dangling bonds in CF were increased at 215 kGy. Charge transfer to the PC occurs, apparently generating stronger bonds, which are possibly covalent, resulting in enhanced adhesion at the CF–PC interface.


  • Open Access

    A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

    by Yoshitake Nishi, Kouhei Sagawa, Michael C. Faudree, Helmut Takahiro Uchida, Masae Kanda, Satoru Kaneko, Michelle Salvia, Yoshihito Matsumura, Hideki Kimura

    New types of hybrid aluminum joints: Al-acrylonitrile butadiene styrene (ABS) carbon fiber reinforced thermoplastic polymer (CFRTP) designated Al/Ni-CFP/ABS, and Al-18-8 Stainless steel, Al/Ni-CFP/18-8, by Ni-plated carbon fiber plug (Ni-CFP) insert not before seen in the literature have been fabricated. The goal is to take advantage of extremely high ~6 mm CF surface area for high adhesion, to enhance the safety level of aircraft and other parts. This is without fasteners, chemical treatment, or glue. First, the CFP is plated with Ni. Second, the higher melting point half-length is spot welded to the CFP; and third, the remaining half-length is fabricated. The ultimate tensile strength (UTS) of Al/Ni-CFP/ABS was raised 15 times over that of Al/ABS. Normalized cUTS according to CFP cross-section by Rule of Mixtures for cAl/Ni-CFP/18-8 was raised over that of cAl/Ni-CFP/18-8 from 140 to 360 MPa. Resistance energy to tensile deformation, UT, was raised 12 times from Al/ABS to Al/Ni-CFP/ABS, and 6 times from Al/CFP/18-8 to Al/Ni-CFP/18-8. Spot welding allows rapid melting followed by rapid solidification for amorphous metal structures minimizing grain boundaries. The Ni-coating lowers or counters the effects of brittle Al4C3 and FexC formation at the interface and prevents damage by impingement to CFs, allowing joints to take on more of the load.


  • Open Access

    A New Strengthening Process for Carbon-Fiber-Reinforced Thermoplastic Polyphenylene Sulfide (CFRTP-PPS) Interlayered Composite by Electron Beam Irradiation to PPS Prior to Lamination Assembly and Hot Press

    by Keisuke Takeda, Hideki Kimura, Michael C. Faudree, Helmut Takahiro Uchida, Kohei Sagawa, Eiichi Miura, Michelle Salvia, Yoshitake Nishi

    Impact by hailstone, volcanic rock, bird strike, or also dropping tools can cause damage to aircraft materials. For maximum safety, the goal is to increase Charpy impact strength (auc) of a carbon-fiber-reinforced thermoplastic polyphenylene sulfide polymer (CFRTP-PPS) composite for potential application to commercial aircraft parts. The layup was three cross-weave CF plies alternating between four PPS plies, [PPS-CF-PPS-CF-PPS-CF-PPS], designated [PPS]4[CF]3. To strengthen, a new process for CFRP-PPS was employed applying homogeneous low voltage electron beam irradiation (HLEBI) to both sides of PPS plies prior to lamination assembly with untreated CF, followed by hot press under 4.0 MPa at 573 K for 8 min. Experimental results showed a 5 kGy HLEBI dose was at or near optimum, increasing auc at each accumulative probability, Pf. Optical microscopy of 5 kGy sample showed a reduction in main crack width with significantly reduced CF separation and pull-out; while, scanning electron microscopy (SEM) and electron dispersive X-ray (EDS) mapping showed PPS adhering to CF. Electron spin resonance (ESR) of a 5 kGy sample indicated lengthening of PPS chains as evidenced by a reduction in dangling bond peak. It Is assumed that 5 kGy HLEBI creates strong bonds at the interface while strengthening the PPS bulk. A model is proposed to illustrate the possible strengthening mechanism.


  • Open Access

    Strengthening Process by Electron Beam to Carbon Fiber for Impact Strength Enhancement of Interlayered Thermoplastic-Polypropylene Carbon Fiber Composite

    by Hideki Kimura, Keisuke Takeda, Helmut Takahiro Uchida, Michael C. Faudree, Kohei Sagawa, Satoru Kaneko, Michelle Salvia, Yoshitake Nishi

    Strong adhesion between recyclable thermoplastic (TP) polymer and carbon fiber (CF) has always been highly sought after. Therefore, for an interlayered CF reinforced TP polypropylene (CFRTPP) composite composed of 3 sized CF plies, alternating between 4 PP sheets, designated [PP]4[CF]3, a process of activating CF plies directly on both sides with homogeneous low energy electron beam irradiation (EBI) under N2 gas, prior to lamination assembly and hot press of 4.0 MPa at 493 K for 3 min was carried out. Experimental results showed EBI dose of 43.2, 129, or 216 kGy significantly raised Charpy impact values, auc at all fracture probabilities, Pf. The 129 kGy dose appeared to be at or near optimum increasing auc 103%, 83%, and 65% at low-, median-, and high-Pf = 0.07, 0.50, and 0.93; while raising statistically lowest impact value, as at Pf = 0 calculated by 3-dimensional Weibull equation about 110%, indicating increased safety and reliability. It is assumed dangling bonds generated by the EBI rapidly form covalent bonds CF:C:O:C:PP and CF:C:C:PP at the interface, along with cross-linking in the PP near the CF. This is by charge transfer from CF to PP.


  • Open Access

    Advances in Titanium/Polymer Hybrid Joints by Carbon Fiber Plug Insert: Current Status and Review

    by Michael C. Faudree, Helmut Takahiro Uchida, Hideki Kimura, Satoru Kaneko, Michelle Salvia, Yoshitake Nishi

    A literature review of up-to-date methods to strengthen Ti/carbon-fiber-reinforced polymer (CFRP) hybrid joints is given. However, there are little or no studies on Ti/CFRP joints by carbon fiber plug insert, which takes advantage of the extremely high surface adhesion area of ~6 μm CFs. Therefore, we cover the current status and review our previously published results developing hybrid joints by a CF plug insert with spot-welded Ti half-lengths to enhance the safety levels of aircraft fan blades. A thermoset Ti/CF/epoxy joint exhibited an ultimate tensile strength (UTS) of 283 MPa when calculated according to the rule of mixtures (RM) for the CF cross-section portion. With concern for the environment, thermoplastic polymers (TPs) allowed recyclability. However, a drawback is easy CF pull-out from difficult-to-adhere TPs due to insufficient contact sites. Therefore, research on a novel method of homogeneous low voltage electron beam irradiation (HLEBI) to activate a bare CF half-length prior to dipping in a TP resin was reviewed and showed that the UTS by the RM of Ti/EBCF/acrylonitrile butadiene styrene (ABS) and Ti/EBCF/polycarbonate (PC) joints increased 154% (from 55 to 140 MPa) and 829% (from 30 to 195 MPa), respectively, over the untreated sample. The optimum 0.30 MGy HLEBI prevented CF pull-out by apparently growing crystallites into the TP around the CF circumference, raising the UTS amount closer to that of epoxy.


  • Open Access

    Increasing Impact Strength of a Short Glass Fiber Compression Molded BMC by Shortening Fibers without Change in Equipment

    by Michael C. Faudree, Yoshitake Nishi, Michelle Salvia

    Bird strike, volcanic rock, hailstones, micrometeoroids, or space debris can cause damage to aircraft and space vehicles, therefore their composite materials must have high impact resistance to maximize safety. In a 55% wt. CaCO3 compression molded short glass fiber polyester GFRP-BMC (bulk molded compound), shortening the nominal 6.4 mm fiber length formulation, by 30 min extended mixing, to 0.44 mm was found to increase Charpy impact values, auc, without a change in the compression molding equipment. Specimens were cut from square panels in a spiral configuration in conformity with ASTM D 6110-02 for orthotropic panels, the flow direction approximately radially outward from the charge. At a median-fracture probability of Pf = 0.50, extended mixing improved auc by 29%, from 7.43 to 9.59 kJm−2, and for each solidification texture angle, namely, 0 to 90 (random), 71, 45 and 18 deg, the auc increased by 25% (6.26 to 7.86 kJm−2), 18% (9.36 to 11.07 kJm−2), 35% (7.68 to 10.37 kJm−2), and 20% (6.96 to 8.36 kJm−2), respectively. This strengthening can be explained by an increased number of thermal compressive stress sites between the glass fiber and matrix due to a difference in the coefficient of thermal expansion (CTE) during cool-down, and shrinkage, with an increased number of spaces between fibers, |Sf| from 217 to approximately 2950 per mm3, enhancing impact energy.


  • A new strengthening process of thermoplastic polypropylene reinforced by interlayered activated sizing film-free carbon fiber treated by electron beam irradiation under oxygen-rich nitrogen gas prior to assembly and hot-press

    by Shodai Kitagawa, Hideki Kimura, Helmut T Uchida, Michael C Faudree, Satoru Kaneko, Tamio Endoh, Michelle Salvia, Yoshitake Nishi

    A new process of activating sizing film free (removed sizing) carbon fiber (SFF-CF) mats directly with electron beam irradiation (EBI) under oxygen-rich nitrogen gas prior to lamination assembly and hot-press was found to increase bending strength of CFRTP (CF reinforced thermoplastic polypropylene (PP)) interlayered composite composed of 3 SFF-CF mats between 4 PP sheets, [PP]4[SFF-CF]3. The hot-press fabrication was performed under 4.0 MPa at 473 K for 1 min. Experimental results showed optimal condition of 0.22 MGy-EBI under 2,000 ppm-O2-rich, protective N2 atmosphere improved bending strength, σb at all accumulative probabilities, Pf over that of untreated. This could be explained by maximum number of the strong covalent bonds of CF:C:C:PP and oxygen assisted CF:C:O:C:PP bonds adhering bare SFF-CF surface to PP, instead of the weak intermolecular bonding of CF(H2O, N2, O2)PP of untreated. The optimal concentration of O2 molecules together with the EBI probably purified the SFF-CF surface simultaneously generating dangling bonds, which already naturally exist in SFF-CF as evidenced by the highest intensity ESR peak whose inflection point was at B = 323 mT. This, along with attaching O groups to the SFF-CF surface can explain the increased SFF-CF to PP adhesion sites and bending strength increase. Fracture analysis showed the optimum condition prevented ply delamination and reduced damage area along sample length appearing to increase cohesion between the difficult to adhere thermoplastic PP and SFF-CF plies to take on higher loads. Although bending strength was increased, carefulness is always highly recommended when investigating unsized CF composites.


  • Improvements of Strength of Layered Polypropylene Reinforced by Carbon Fiber by its Sizing Film and Electron Beam Under Protective Nitrogen Gas Atmosphere

    by Yoshitake Nishi, Shodai Kitagawa, Michael C. Faudree, Helmut Takahiro Uchida, Masae Kanda, Sagiri Takase, Satoru Kaneko, Tamio Endo, Akira Tonegawa, Michelle Salvia, et al.