OSOleksandr Savchenko

Oleksandr Savchenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oleksandr Savchenko has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Devising a technique for constructing approximate sweeps of helicoids based on the theory of surface bending

    by Andrii Nesvidomin, Serhii Pylypaka, Tetiana Volina, Tetiana Kresan, Oleksandr Savoiskyi, Oksana Yurchenko, Oleksandr Savchenko, Serhii Borodai, Olha Zalevska, Olena Nalobina

    This study investigates the process of constructing approximate helicoid sweeps based on the classical theory of their continuous bending in the surface of revolution. Straight helicoids are non-sweep surfaces; therefore, a flat workpiece for fabricating them can only be an approximate sweep. Such an approximate sweep is a flat ring bounded by the inner and outer arcs of circles whose radii are tabular data. The dimensions of the ring must be such as to ensure a minimum of plastic deformations when forming them into a helicoid coil. To find the dimensions of the ring, the classical theory of bending of non-sweep surfaces has been applied. According to the theorem of differential geometry, any helical surface can be bent into a surface of revolution. Such bending is carried out by reducing the pitch of the surface to zero: that makes it possible to visually observe the deformation of the surface. The resulting surface of revolution can be approximated by a truncated cone. The exact sweep of the truncated cone will be an approximate sweep of the helicoid turn. This approach is based not on experimental data but on theoretical approaches to the bending process. Depending on the type of helicoid, the surface of revolution can be a catenoid or a single-cavity hyperboloid of revolution. This makes it possible to choose such sections of the surface of revolution for approximation by a truncated cone where it most closely fits it. This will correspond to the minimum of plastic deformations when forming the sweep of the cone into a helicoid turn. In this work, approximate sweeps have been constructed for straight closed and open helicoids with the same design data: surface pitch, H = 100 linear units; radii of the cylinders bounding the surface, r = 20 linear units; and R = 60 linear units. The results are attributed to a new approach to finding approximate sweeps using the theory of bending of non-sweeping surfaces

  • Open Access

    АДАПТАЦІЯ КОШТОРИСНОГО ЦІНОУТВОРЕННЯ ДО ЗМІН В ОРГАНІЗАЦІЇ БУДІВЕЛЬНОГО ВИРОБНИЦТВА

    by Оксана Юрченко, Олександр Савченко, Валентина Нестеренко

    УДК 338.5:69.003; JEL Classification : L74, M11, M21 Юрченко О.В., Савченко О.С., Нестеренко В.Ю. АДАПТАЦІЯ КОШТОРИСНОГО ЦІНОУТВОРЕННЯ ДО ЗМІН В ОРГАНІЗАЦІЇ БУДІВЕЛЬНОГО ВИРОБНИЦТВА Мета. Метою дослідження є розвиток та обґрунтування теоретичних засад адаптації кошторисного ціноутворення до динамічних змін в організації будівельного виробництва з урахуванням впливу економічної нестабільності. Методика дослідження. Методологічну основу роботи сформовано на поєднанні системного, структурно-логічного та порівняльного аналізу. Для дослідження особливостей формування кошторисної вартості застосовано метод теоретичного узагальнення. Дослідження впливу організаційно-виробничих змін на процес ціноутворення здійснювалось із використанням підходів до інтеграції технологічних, ресурсних і ринкових параметрів у систему кошторисних розрахунків. Результати. У статті досліджено економічну сутність кошторисного ціноутворення та визначено ключові фактори, що впливають на формування вартості будівельної продукції. Обґрунтовано взаємозв’язок між організацією будівельного виробництва та структурою кошторисних витрат. Встановлено, що сучасні зміни у виробничих процесах, зумовлені нестабільністю ресурсного забезпечення, ускладненням логістики та впливом макроекономічних чинників, потребують перегляду традиційних підходів до ціноутворення. Запропоновано підхід до адаптації кошторисного ціноутворення, який передбачає інтеграцію організаційно-технологічних параметрів, гнучке врахування змін вартості ресурсів та використання цифрових інструментів для підвищення точності розрахунків. Доведено доцільність застосування комплексного підходу до формування вартості будівництва, що поєднує нормативні, ринкові та організаційні складові. Наукова новизна. Наукова новизна. Удосконалено теоретичні підходи до кошторисного ціноутворення у будівництві шляхом обґрунтування необхідності його адаптації до змін в організації будівельного виробництва. Розвинуто підхід до інтеграції організаційно-виробничих факторів у процес формування кошторисної вартості з урахуванням динамічних змін зовнішнього середовища. Практична значущість. Практична значущість отриманих результатів полягає у можливості використання запропонованих підходів для підвищення точності визначення вартості будівництва, удосконалення системи планування витрат та зниження ризиків перевитрат у будівельних проєктах. Результати дослідження можуть бути застосовані будівельними підприємствами, проєктними організаціями та органами державного управління при формуванні кошторисної документації, розробці інвестиційних проєктів та впровадженні цифрових рішень у сфері ціноутворення.

  • Open Access

    ORGANIZATION OF DISMANTLING WORKS AND CONSTRUCTION WASTE MANAGEMENT IN THE CONTEXT OF THE CIRCULAR ECONOMY

    by Oleksandr Savchenko, Lidiya Savchenko

    The article presents a comprehensive study of the methodological and organizational foundations for transforming the construction industry based on the principles of the circular economy. The relevance of the work is driven by the urgent need to find effective solutions for managing unprecedented volumes of demolition waste in Ukraine, as well as the necessity of adapting national legislation to European Union environmental directives. The author substantiates that shifting from traditional linear demolition to selective deconstruction is a fundamental condition for implementing a closed-loop economy, where a building is viewed as a «material bank» for future construction.The study details the «Design for Disassembly» (DfD) concept, which involves considering the possibility of reverse assembly as early as the project design stage. Special attention is paid to the stages of organizing works based on the «reverse production line» principle, which includes conducting pre-demolition audits, identifying hazardous substances, and sorting waste at the source of its generation. It is proved that the separate collection of fractions directly on-site is a critical factor in maintaining the liquidity of secondary raw materials.The role of digital tools, particularly BIM technologies and digital material passports, in creating transparent supply chains and assessing the residual value of structures is investigated. The article provides a comparative analysis of environmental impacts, demonstrating a significant reduction in «embodied carbon» when reusing steel and concrete compared to manufacturing new materials. The practical significance of the research lies in the development of a model for using mobile processing plants directly at destruction sites, which minimizes logistical costs and provides a rapid resource base for the post-war recovery of communities. Proposals for improving the regulatory framework regarding the certification of secondary building materials for their full-scale market introduction are formulated.

  • Open Access

    Devising a technique for constructing tubular surfaces referred to a coordinate grid of lines of curvature

    by Andrii Nesvidomin, Serhii Pylypaka, Tetiana Volina, Victor Nesvidomin, Oleksandr Solarov, Taras Voloshko, Taras Pylypaka, Lidiia Savchenko, Oleksandr Savchenko, Irina Zakharova

    This study considers the construction of tubular surfaces with a spatial axis of slope, referred to a coordinate grid of curvature lines. Such surfaces have a number of mathematical advantages compared to surfaces described by arbitrary coordinate grids. In differential geometry, this has a theoretical justification and applied value. This follows from the special role of curvature lines as geometrically privileged directions on a surface with minimal and maximal curvatures. To parameterize a tubular surface in this way, it is necessary that the length of its axis be described by analytical dependences in a finite form. Typically, the length of spatial curves is determined by numerical integration. There is a known group of plane curves that are described by parametric equations as a function of the arc length and for which such a problem does not exist. This work proposes taking such curves as a horizontal projection of a spatial curve. The spatial curve should be constructed as a slope curve with a constant elevation angle relative to the horizontal plane. Then the spatial curve, the equations of which include the elevation angle, will be described as a function of the arc length. Its use as the axis of the tubular surface makes it possible to attribute the latter to the families of coordinate lines of curvature. In this paper, the horizontal projection of the axis of the tubular surface is a logarithmic spiral. Parametric equations of the tubular surface in analytical form have been derived. A surface with the elevation angle of the axis β = 10° and the radius of the generating circle ρ = 15 linear units was constructed. The orthogonality of the resulting coordinate grid has been proven through the analysis of the coefficients of the first quadratic form (F = 0), which confirms the assignment of the surface to the lines of curvature. This makes it possible to improve the accuracy of calculating the stress-strain state of shells in mechanical engineering and aerospace engineering at simultaneous minimization of computational costs

  • Optimal organization of logistics of accelerated construction

    by Lidiia Savchenko, Oleksandr Savchenko

    Introduction. The need for accelerated construction becomes particularly acute in the context of overcoming the consequences of emergencies, military conflicts, as well as during the deployment of large-scale industrial and logistics complexes in a short time. The traditional model of construction organization, which involves phased planning with long cycles of stock accumulation, has exhausted its potential in a dynamic environment, since it is unable to flexibly respond to the shortage of time resources. In this regard, the relevance of the study is due to the objective need to develop new models of logistics support that would allow transforming logistics from an auxiliary function into an intelligent driver of the production process. The issue of logistics support for accelerated construction covers a number of critical challenges, the primary among which is the synchronization of supply and installation processes. In conditions of construction of objects in a short time, such as modular buildings or mobile hospitals, there is practically no time resource for warehousing, so any delay in delivery even for a few hours leads to downtime of equipment and personnel. This necessitates the transition to the Just-in-Time system, where materials are supplied «from the wheels» directly to the installation area. In parallel, the problem of shortage of warehouse and maneuvering areas arises, since the high pace of work requires the simultaneous presence of a significant number of resources on the site. Excessive accumulation of materials leads to «overcrowding» of the territory, which blocks access roads and the operation of cranes; the solution to this problem is the creation of intermediate logistics hubs and consolidation centers outside the facility. Objective. To develop a model of optimal organization of logistical support for accelerated construction of social infrastructure, aimed at minimizing the impact of logistical and resource constraints. Materials and methods. Analytical: supply chain analysis: determination of all stages of material movement from the manufacturer to the site and identification of risk points. Comparative analysis: comparison of the cost and delivery terms of imported and domestic analogues; organizational modeling: modeling of «bottlenecks»: creation of a simulation model (network graph) to assess the impact of a delay in the delivery of critical material (concrete, reinforcement, sandwich panels) on the overall project duration. Results. An attempt was made to identify and classify key logistics niches in the current construction supply chain. Organizational schemes that successfully use complete deliveries to minimize warehouse needs were analyzed. The economic feasibility of switching to domestic materials as a way to reduce dependence on international logistics was substantiated. Recommendations were developed for organizational planning of supplies in conditions of constantly changing security situations. Conclusions. Analysis of the features of logistics organization allows us to state that in conditions of accelerated construction, the time factor becomes critical, as a result of which the logistics system ceases to play only a supporting role and becomes a strategic factor that determines the overall pace of work. In this regard, the transition to the Just-in-Time supply model appears as a prerequisite for avoiding production downtime and ensuring the continuity of installation processes. An important aspect of space optimization is the use of external consolidation centers (hubs), which is defined as the most effective way to solve the problem of space shortage at the construction site, ensuring high maneuverability of equipment and proper organization of access roads.

  • Open Access

    Substantiating the rational shape of a drum-type working tool for surface soil treatment

    by Andrii Nesvidomin, Serhii Pylypaka, Zinovii Ruzhilo, Tetiana Volina, Yurii Liannoi, Svitlana Botvinovska, Irina Zakharova, Lidiia Savchenko, Oleksandr Savchenko, Irina Rybenko

    The working bodies of agricultural implements should minimize resistance to movement. The shape of a curved tooth, which is fixed between two cylindrical disks, has been considered in this paper. Several such sections on the shaft form a drum similar to a harrow roller or a needle harrow. When rolling, the tooth sinks into the soil, followed by its loosening. The task was to find such a shape of the tooth, which at the first stage of immersion in the soil would slide over it as much as possible with minimal deformation, and at the second stage would balance it and turn it over. The object of the study is a drum-type working body. The work of a straight tooth with its transformation into a curved tooth was analyzed. As a result of such an analysis and subsequent search, a rational shape of a drum-type tillage working body was obtained for the purpose of reducing resistance when it is buried in the soil. The involute of a circle turned out to be such a curve. A tooth in the form of an involute of a circle has a peculiarity: at the moment of contact of the tooth with the ground, the absolute velocity vector is directed perpendicular to it. The result is explained by the fact that as the disks roll, the tooth sinks into the soil, and the point of entry remains unchanged, and the tooth itself slides practically along itself, especially in the upper layers of the soil. In known working bodies, their curvilinear form was selected experimentally. The proposed shape of the working body was obtained analytically. To reduce the resistance of the teeth entering the soil, the ratio of the tillage depth to the radius of the drum is important. The immersion of the blade to the full depth should correspond to a 30° rotation of the drum. After diving to the maximum depth, it begins to weigh the soil to the surface or loosen it. The field of application of such a tooth shape can be the improvement of the working bodies of tillage implements

  • Open Access

    Analyzing the causes of crack formation in porcelain and the ways to eliminate them

    by Olena Khomenko, Borys Datsenko, Olga Hurzhii, Lidiia Savchenko, Oleksandr Savchenko

    The studies deal with the porcelain products produced by casting finely-dispersed slips into gypsum molds. The causes of the occurrence of cracks on the edges of products after bisque and glazed firing were established and the ways of their elimination were proposed.As a result of the comprehensive research into the basic ceramic mass of the assigned composition and products from it, a series of the technological factors that cause cracking were determined.Determining the fineness of grinding of production slips of various batches showed that the residue on sieve No. 0063 ranged from 0.7 to 3.5 %. The direct correlation between the occurrence of cracks in products and an elevated indicator of the residue that contributed to the stratification of a ceramic slip in the process of settling in gypsum molds was established. This led to the emergence of internal stresses in the structure of a potsherd. It was established that another factor that caused cracking of products was the existence in the composition of the ceramic mass of large quartz grains, which in the heating-cooling process are capable of modification transformations. In addition, the low temperature of bisque firing did not contribute to the completion of the process of dehydration of clay and mica minerals, which strengthened the internal stresses in a potsherd.The research revealed that to ensure qualitative indicators of ceramic products, it is necessary not only to control the residue on a sieve but also to take into consideration the distribution of the fractional composition of a ceramic slip, while the content of the quartz component of 30–63 µm should not exceed 12 % by weight. This contributes to the formation of a dense homogeneous potsherd with a high content of a mullite phase.As a result of the research, it was also proposed to change the temperature of bisque firing from 660 to 800 °C. It is at this temperature that the processes of dehydration of layered silicates are completed and the shrinkage processes are stabilized.The obtained results can be applied at the typical production of household products from low-temperature porcelain


  • Open Access

    Patterns in the synthesis processes and the characteristics of silicate-spinal ceramic pigments when introducing mineralizers

    by Oleksandr Zaichuk, Аleksandra Amelina, Olena Khomenko, Nataliia Sribniak, Liudmyla Tsyhanenko, Oleksandr Savchenko, Oleksandr Telichenko

    Patterns in the synthesis processes and the characteristics of silicate-spinal ceramic pigments when introducing mineralizers