LZLin Zhao

Lin Zhao

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lin Zhao has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High-Density 3D-SiP Vertical Interconnect: Structural Design and Process Sensitivity Analysis for Enhanced Electrical Performance

    by Mingqi Gao, An Zhang, Yueyou Yang, Tong Hu, Chunlei Dang, Lin Zhao, Yagang Zhang

    To meet the demands for high-density integration and broadband RF performance in next-generation electronic equipment, this paper investigates the structural design and process sensitivity of vertical interconnects in three-dimensional stacked system-in-package (3D-SiP). Based on quasi-coaxial matching and low-impedance compensation techniques, three typical vertical interconnect structures are designed: the PCB-BGA-SiP microstrip structure achieves S11 better than −15 dB and S21 < 0.3 dB within 2–20 GHz; the lower stripline–BGA–upper microstrip structure achieves S11 better than −27 dB; the lower microstrip–BGA–upper microstrip structure achieves S11 better than −18 dB within 1–23 GHz. Isolation simulation shows that the isolation between adjacent channels exceeds 55 dB within 25 GHz. For process sensitivity evaluation, physical samples of gold wire bonding parameters (length, diameter, number) were fabricated and tested for S11, confirming that the dual-wire topology extends the effective bandwidth to 2–20 GHz (a 54% improvement over single wire), the third-wire marginal gain is only ~5%, and 25 μm diameter offers the best overall performance. For BGA ball radius and pad pitch, parametric sensitivity analysis via Ansys HFSS was performed (not experimentally validated process variation results), identifying the optimal BGA radius as 0.245 mm with an allowable variation of ±0.015 mm, and the pad center-to-center distance should be controlled near 0.8 mm. Based on these findings, process control strategies are proposed: low-loop wire bonding (loop height < 50–80 μm) with statistical process control; substrate warpage controlled through symmetric copper filling, a thick-middle dielectric stack-up, and distributed symmetric cavity layout, combined with eutectic pressure of 1.5 kPa, validated on 10 fabricated substrates with peak warpage consistently < 80 μm, void rate 4.75%, and solder overflow 94%; and BGA soldering using high-precision vision alignment and controlled collapse (20–35%). This work provides a theoretical basis and practical process pathway for transitioning 3D-SiP vertical interconnects from ideal design to mass production.

  • Open Access

    Preparation of Phenolic Epoxy-Based Electronic Packaging Materials with High Thermal Conductivity by Creating an Interfacial Heat Conduction Network

    by Minghao Ye, Jing Jiang, Lin Zhao, Hongyu Zhu, Junjie Wang, Zicai Sun, Dewei Zhang, Ming Li, Yagang Zhang

    As one of the most widely used packaging materials, epoxy composite (EP) offers excellent insulation properties; however, its intrinsic low thermal conductivity (TC) limits its application in high-frequency and high-power devices. To enhance the TC of EP, six highly thermally conductive inorganic fillers, namely, Al2O3, MgO, ZnO, Si3N4, h-BN, and AlN, were incorporated into the EP matrix at varying contents (60–90 wt.%). The resulting epoxy molding compounds (EMCs) demonstrated significant improvement in thermal conductivity coefficient (λ) at high filler contents (90 wt.%), ranging from 0.67 W m−1 K−1 to 1.19 W m−1 K−1, compared to the pristine epoxy composite preform (ECP, 0.36 W m−1 K−1). However, it was found that the interfacial thermal resistance (ITR) between EP and filler materials is a major hindrance restricting TC improvement. In order to address this challenge, graphene nanosheets (GNSs) and carbon nanotubes (CNTs) were introduced as additives to reduce the ITR. The experimental results indicated that CNTs were effective in enhancing the TC, with the optimized EMC achieving a λ value of 1.14 W m−1 K−1 using 60 wt.% Si3N4 + 2 wt.% CNTs. Through the introduction of a small amount of CNT (2 wt.%), the inorganic filler content was significantly reduced from 90 wt.% to 60 wt.% while still maintaining high thermal conductivity (1.14 W m−1 K−1). We propose that the addition of CNTs helps in the construction of a partial heat conduction network within the EP matrix, thereby facilitating interfacial heat transfer.


  • Open Access

    Preparation and Characterization of Low-Molecular-Weight Polyacrylonitrile

    by Yuanteng Yang, Xiaoli Jiang, Jing Jiang, Yang Liu, Lin Zhao, Hongyu Zhu, Junjie Wang, Zongkai Yan, Yagang Zhang

    Polyacrylonitrile (PAN) is renowned for its excellent physical and chemical properties, making it a promising candidate for producing high-performance and energetic materials. However, traditional high-molecular-weight PAN suffers from poor solubility and low reactivity, which limits its application as a precursor for advanced materials. To overcome these issues, this study successfully synthesized low-molecular-weight PAN (Mη: 6.808 kDa) using an environmentally friendly aqueous precipitation polymerization method, utilizing ammonium persulfate (6 wt% relative to the monomer mass) as the initiator and isopropanol (400 wt%) as the chain transfer agent. The structures and properties of the synthesized low-molecular-weight PAN were analyzed in depth. The morphology and chain structure of PAN were characterized using field-emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FT-IR), and nuclear magnetic resonance hydrogen spectroscopy (1H NMR). The thermal properties were assessed using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Additionally, the state changes during the heating process of PAN with different molecular weights were directly observed using a visual melting point analyzer for the first time. Furthermore, the influence of molecular weight on PAN’s solubility was investigated in detail. Based on that, a linear regression between the viscosity average molecular weight (Mη) and the number average molecular weight (Mn) was established, providing simple and rapid access to the molecular weight of the synthesized PAN via viscosity measurements. Our study employed CTA-controlled aqueous precipitation polymerization to prepare low-molecular-weight PAN, which possesses significant potential in producing tetrazole-based energetic materials.


  • Open Access

    Molecular Entanglement Facilitated Improvement of Thermal Stability of Cellulose Diacetate

    by Yang Liu, Yin Hu, Jianyu Chen, Zongkai Yan, Lin Zhao, Falu Zhan, Junjie Wang, Yagang Zhang

    As a renewable and degradable biomass material, cellulose diacetate (CDA) has significant development potential and has gained widespread interest from researchers. However, its poor thermal stability at high temperatures limits its practical use in the extrusion process and restricts its applications in other fields, such as high-heat airflow filters, battery separators and special textile materials. To enhance the thermal stability of CDA, three heat-resistance additives, i.e., polyphenylene sulfide (PPS), polycarbonate (PC) and polyimide (PI), were introduced to synthesize PPS/CDA, PC/CDA and PI/CDA composite materials through melt extrusion. The incorporation of three heat-resistant additives increased the glass transition temperature (Tg), initial melting temperature (Tmi) and final melting temperature (Tmf) of the composites, and it reduced the heat loss at 195 °C. After conducting the isothermal thermogravimetry test for 3 h at 215 °C in an air atmosphere, the weight loss of PPS/CDA, PC/CDA and PI/CDA composites was 4.6%, 4.1% and 3.7%, respectively, which was 5.1% lower than that of pure CDA. Morphology characterization tests using a 3D digital microscope and a field emission scanning electron microscope (FESEM) revealed the compatibility order with CDA as the following: PC > PPS > PI. Additionally, Fourier transform infrared spectroscopy (FT–IR) disclosed that hydrogen bonds were formed between heat-resistant additives and CDA molecules, and the carbonyl groups in CDA showed conjugation and hyperconjugation effects with the benzene rings in the additives. Therefore, the enhanced thermal stability of CDA composites can be attributed to the molecular entanglement and crosslinking between additives and CDA molecules.


  • Open Access

    Controlled Multi-Dimensional Assembly of Calcium Carbonate Particles with Industrial By-Product Carbide Slag and CO2

    by Yuke Shen, Xiaoli Jiang, Chengcai Tang, Wei Ma, Jianyu Cheng, Hongxu Wang, Hongyu Zhu, Lin Zhao, Yagang Zhang, Panfeng Zhao

    The utilization of carbide slag, an industrial by-product, as a resource to prepare value-added products has a profound impact not only for sustainable synthesis and the circular economy but also for CO2 reduction. Herein, we report the very first example of the controlled multi-dimensional assembly of calcium carbonate particles at the micrometer scale with industrial by-product carbide slag and CO2. Calcium carbonate particles of distinctly different sizes, shapes, and morphologies are obtained by finely tuning the assembly conditions. This strategy yields diverse assembled structures, including simple cubic, mulberry-like assembled unit, stacked cubic polycrystalline, and rotated polycrystalline structures, using the same starting materials. This innovative approach not only highlights the adaptability and efficiency of utilizing industrial by-products via multi-dimensional assembly but also provides new insights into the potential applications of the resulting calcium carbonate.


  • Open Access

    Enhanced Electrocatalytic Nitrate Reduction to Ammonia Using Functionalized Multi-Walled Carbon Nanotube-Supported Cobalt Catalyst

    by Minghao Ye, Xiaoli Jiang, Yagang Zhang, Yang Liu, Yanxia Liu, Lin Zhao

    Ammonia (NH3) is vital in modern agriculture and industry as a potential energy carrier. The electrocatalytic reduction of nitrate (NO3−) to ammonia under ambient conditions offers a sustainable alternative to the energy-intensive Haber−Bosch process. However, achieving high selectivity in this conversion poses significant challenges due to the multi-step electron and proton transfer processes and the low proton adsorption capacity of transition metal electrocatalysts. Herein, we introduce a novel approach by employing functionalized multi-walled carbon nanotubes (MWCNTs) as carriers for active cobalt catalysts. The exceptional conductivity of MWCNTs significantly reduces charge transfer resistance. Their unique hollow structure increases the electrochemical active surface area of the electrocatalyst. Additionally, the one-dimensional hollow tube structure and graphite-like layers within MWCNTs enhance adsorption properties, thus mitigating the diffusion of intermediate and stabilizing active cobalt species during nitrate reduction reaction (NitRR). Using the MWCNT-supported cobalt catalyst, we achieved a notable NH3 yield rate of 4.03 mg h−1 cm−2 and a high Faradaic efficiency of 84.72% in 0.1 M KOH with 0.1 M NO3−. This study demonstrates the potential of MWCNTs as advanced carriers in constructing electrocatalysts for efficient nitrate reduction.


  • Open Access

    Controllable Synthesis of Nano-Micro Calcium Carbonate Mediated by Additive Engineering

    by Yuke Shen, Shuang Hao, Angqian Suonan, Yanxia Liu, Hangqi Li, Wei Ma, Lin Zhao, Yagang Zhang

    Nano-micro calcium carbonate has a small particle size, uniform distribution, and good dispersion performance, offering great research value and development prospects. It has been widely used as a filler material for rubber, paper, ink, pigments, and coatings. Developing an efficient and controllable approach to preparing nano-micro calcium carbonate with adjustable morphology and controllable size has significant economic and environmental benefits. This study reports the controllable synthesis of nano-micro calcium carbonate meditated by additive engineering. The effects of various additives including inorganic acids, organic acids, alcohol, and surfactants on the particle size and morphology of the prepared materials were investigated. SEM, FT-IR and other characterization methods were used to analyze the prepared nano-micro calcium carbonate particle size, dispersion, and uniformity. The results showed that the particle size of calcium carbonate was 4~7 μm with a cubic structure. The particle size of calcium carbonate prepared by adding surfactant additives is in the range of 1~4 μm, and the crystal shape of calcium carbonate changes from calcite to vaterite after adding sodium dodecyl benzene sulfonate. With the aid of additives, the calcium carbonate particles dispersed more evenly. The mechanism of the controllable synthesis of nano-micro calcium carbonate mediated by additive engineering is elucidated and discussed. SDBS was found to be the best additive for preparing nano-micro calcium carbonate, and the synthesis conditions were explored and optimized.


  • Open Access

    Inorganic Skeleton Reinforcement—A Generic Approach to Improve the Mechanical Properties of Biochar

    by Zhikai Chen, Xiaoli Jiang, Yagang Zhang, Wei Li, Zhiqiang Tang, Yanxia Liu, Lin Zhao

    Biochar is considered as a promising candidate for emerging sustainable energy systems and environmental technology applications. However, the improvement of mechanical properties remains challenges. Herein, we propose a generic strategy to enhance the mechanical properties of bio-based carbon materials through inorganic skeleton reinforcement. As a proof-of-concept, silane, geopolymer, and inorganic gel are selected as precursors. The composites’ structures are characterized and an inorganic skeleton reinforcement mechanism is elucidated. Specifically, two types of reinforcement of the silicon-oxygen skeleton network formed in situ with biomass pyrolysis and the silica-oxy-al-oxy network are constructed to improve the mechanical properties. A significant improvement in mechanical strength was achieved for bio-based carbon materials. The compressive strength of well-balanced porous carbon materials modified by silane can reach up to 88.9 kPa, geopolymer-modified carbon material exhibits an enhanced compressive strength of 36.8 kPa, and that of inorganic-gel-polymer-modified carbon material is 124.6 kPa. Moreover, the prepared carbon materials with enhanced mechanical properties show excellent adsorption performance and high reusability for organic pollutant model compound methylene blue dye. This work demonstrates a promising and universal strategy for enhancing the mechanical properties of biomass-derived porous carbon materials.


  • Open Access

    Design and Synthesis of Functional Silane-Based Silicone Resin and Application in Low-Temperature Curing Silver Conductive Inks

    by Zhiqiang Tang, Yanxia Liu, Yagang Zhang, Zicai Sun, Weidong Huang, Zhikai Chen, Xiaoli Jiang, Lin Zhao

    In the field of flexible electronics manufacturing, inkjet printing technology is a research hotspot, and it is key to developing low-temperature curing conductive inks that meet printing requirements and have suitable functions. Herein, methylphenylamino silicon oil (N75) and epoxy-modified silicon oil (SE35) were successfully synthesized through functional silicon monomers, and they were used to prepare silicone resin 1030H with nano SiO2. 1030H silicone resin was used as the resin binder for silver conductive ink. The silver conductive ink we prepared with 1030H has good dispersion performance with a particle size of 50–100 nm, as well as good storage stability and excellent adhesion. Additionally, the printing performance and conductivity of the silver conductive ink prepared with n,n-dimethylformamide (DMF): proprylene glycol monomethyl ether (PM) (1:1) as solvent are better than those of the silver conductive ink prepared by DMF and PM solvent. Cured at a low temperature of 160 °C, the resistivity of 1030H-Ag-82%-3 conductive ink is 6.87 × 10−6 Ω·m, and that of 1030H-Ag-92%-3 conductive ink is 0.564 × 10−6 Ω·m, so the low-temperature curing silver conductive ink has high conductivity. The low-temperature curing silver conductive ink we prepared meets the printing requirements and has potential for practical applications.


  • Open Access

    Improved the response time of WO3 thin film by deposition of Ag nanolayers

    by Lin Zhao, Shipai Song, Le Li

    The effects of different Ag layer thicknesses on the optical properties of WO3-Ag-WO3 composite films are studied by magnetron sputtering. The research of WO3-Ag-WO3 composite films reveals that the introduction of Ag layer is not conducive to improving the transmittance ability of the film, and the transmittance modulation amplitude decreases with the increase of Ag layer thickness. However, with the increase of the Ag layer thickness, the response time and the cycle stability of the films have been significantly improved. However, electrochromic performances will decline when Ag was sputtered too long. Taken together, in this experiment, when the sputtering time of Ag layer is about 6min, the electrochromic device assembled by composite thin film can obtain the most excellent electrochromic performances.