Ricardo Andrés Mendoza Quiroga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ricardo Andrés Mendoza Quiroga has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Edgardo Manuel Buelvas Castro
Universidad Autónoma del Caribe
1 shared publication - Fabio Bermejo Altamar
Universidad Autónoma del Caribe, Barranquilla, Colombia
1 shared publication Jairo Chimento
Mechanical Engineering, University of South Florida, Tampa, Florida, USA
1 shared publicationJennifer Villa Domínguez
Department of Civil and Environment, Universidad de la Costa, Barranquilla, Colombia
1 shared publicationJonathan Fabregas-Villegas
Mechanical Engineering, Universidad Autónoma del Caribe, Barranquilla, Colombia
1 shared publicationNohora Mercado-Caruso
Department of Productivity and Innovation, Universidad de La Costa, Barranquilla, Colombia
1 shared publication
Latest Publications
- 5 March 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 19 (15) , 11818-11830
Effect of the Morphology Measuring Methods of Coconut Fiber on the Determination of Mechanical Tensile Properties
This study is intended to improve the methodology to calculate the tensile properties of natural coconut fiber and increasing confidence in the use of sustainable natural fibers as reinforcing in composites used for different components in the naval industry. Coconut fiber is an agribusiness by-product that has been shown to have the potential for the development of new materials. The morphology of different species of coconut fiber was studied, and their mechanical tensile properties were determined. The coconut fibers were tested under direct tension in a universal testing machine, and the cross-sectional area of the fibers was calculated using images obtained in an optical microscope and a scanning electron microscope. The study assessed the incidence of key factors to determine coconut fiber mechanical tensile properties including different area measuring methods and the percentage of lumens present through an image analysis software called ImageJ. The results indicate that coconut fiber has a round-shaped cross-section, and the percentage of lumens is between 15% and 27%. Therefore, the effective area is reduced increasing the fiber’s ultimate resistance to tension.
- 5 March 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 19 (15) , 11818-11830
Effect of the Morphology Measuring Methods of Coconut Fiber on the Determination of Mechanical Tensile Properties
This study is intended to improve the methodology to calculate the tensile properties of natural coconut fiber and increasing confidence in the use of sustainable natural fibers as reinforcing in composites used for different components in the naval industry. Coconut fiber is an agribusiness by-product that has been shown to have the potential for the development of new materials. The morphology of different species of coconut fiber was studied, and their mechanical tensile properties were determined. The coconut fibers were tested under direct tension in a universal testing machine, and the cross-sectional area of the fibers was calculated using images obtained in an optical microscope and a scanning electron microscope. The study assessed the incidence of key factors to determine coconut fiber mechanical tensile properties including different area measuring methods and the percentage of lumens present through an image analysis software called ImageJ. The results indicate that coconut fiber has a round-shaped cross-section, and the percentage of lumens is between 15% and 27%. Therefore, the effective area is reduced increasing the fiber’s ultimate resistance to tension.
- Open Access
- 30 March 2020
- Published by Universidad Tecnologica de Pereira - UTP in Scientia et technica
- Vol. 25 (1) , 30-36
Failure analysis and repair of the telescopic beam belonging to the spreader of a reach stacker for port operations
Reach stackers land equipment operating in ports of the Colombian Caribbean, are subject to several critical working conditions such as; corrosive environment, excess working hours, overload and lack of predictive maintenance. This work focuses on the failure analysis and the elaboration of the welding repair procedure of the telescopic beam belonging to the spreader of a Reach stacker that operates in a Colombian Caribbean seaport. Initially the fault zone was characterized; by mean a metallographic analysis and a hardness profile to identify the type of structural steel of which the beam is composed, obtaining an A514 grade C of 110KSI of tensile strength and 34HRC of hardness. The equipment manufacturer was verified and the established by the laboratory tests was corroborated. After identifying the material, the fracture area was analyzed where patterns of beach markings were found, typical of a fatigue failure which extended from the circumference of separating pins to the surface of the beam. The inclusion of the separators in the initial design generates stress concentrators in the welding of the pins which increases the fatigue zone combined with the excess load with which the equipment works. This fact could be verified with a technical bulletin published by the manufacturer brand "Taylor" where it indicates this type of failure for the telescopic beam of the Reach stackers. Successively, an FCAW type welding repair procedure is developed in accordance with AWS code D1.1, where the electrode to be used, the cords to be applied, the preheating, and the speeds and conditions recommended for filling the materials are selected cracks. Finally it could be concluded that the fault was generated by fatigue and overload in the welding of the telescopic beam separator pins and its repair will be carried out according to a welding procedure of the AWS code D1.1. The analysis of these types of cases will allow the company to take actions to minimize the new occurrence of the failure such as periodic reviews in that area after the work hours recommended by the manufacturer and the awareness of the equipment operators with the handling of loads on the dock.
- 30 March 2020
- Published by Universidad Tecnologica de Pereira - UTP in Scientia et technica
- Vol. 25 (1) , 30-36
Open AccessFailure analysis and repair of the telescopic beam belonging to the spreader of a reach stacker for port operations
Reach stackers land equipment operating in ports of the Colombian Caribbean, are subject to several critical working conditions such as; corrosive environment, excess working hours, overload and lack of predictive maintenance. This work focuses on the failure analysis and the elaboration of the welding repair procedure of the telescopic beam belonging to the spreader of a Reach stacker that operates in a Colombian Caribbean seaport. Initially the fault zone was characterized; by mean a metallographic analysis and a hardness profile to identify the type of structural steel of which the beam is composed, obtaining an A514 grade C of 110KSI of tensile strength and 34HRC of hardness. The equipment manufacturer was verified and the established by the laboratory tests was corroborated. After identifying the material, the fracture area was analyzed where patterns of beach markings were found, typical of a fatigue failure which extended from the circumference of separating pins to the surface of the beam. The inclusion of the separators in the initial design generates stress concentrators in the welding of the pins which increases the fatigue zone combined with the excess load with which the equipment works. This fact could be verified with a technical bulletin published by the manufacturer brand "Taylor" where it indicates this type of failure for the telescopic beam of the Reach stackers. Successively, an FCAW type welding repair procedure is developed in accordance with AWS code D1.1, where the electrode to be used, the cords to be applied, the preheating, and the speeds and conditions recommended for filling the materials are selected cracks. Finally it could be concluded that the fault was generated by fatigue and overload in the welding of the telescopic beam separator pins and its repair will be carried out according to a welding procedure of the AWS code D1.1. The analysis of these types of cases will allow the company to take actions to minimize the new occurrence of the failure such as periodic reviews in that area after the work hours recommended by the manufacturer and the awareness of the equipment operators with the handling of loads on the dock.