Peter Blennow
Research Subjects
Research Interests
Peter Blennow has a total of 92 co-authors. Here are the top co-authors by number of shared publications:
- Mogens Mogensen
Technical University of Denmark
11 shared publications - Bhaskar Reddy Sudireddy
Department of Energy Conversion and Storage, Technical University of Denmark, Lyngby, Denmark
8 shared publications - Jimmi Nielsen
Department of Energy Conversion and Storage, Technical University of Denmark, 4000 Roskilde, Denmark
8 shared publications - Johan Hjelm
Technical University of Denmark
7 shared publications - Severine Ramousse
Technical University of Denmark
6 shared publications - Kent Kammer Hansen
Department of Energy Conversion and Storage, Technical University of Denmark
5 shared publications
Latest Publications
- 9 December 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (48) , 42166-42177
Unravelling the role of Si and Al impurities in Ni/YSZ fuel electrode degradation in solid oxide electrolysis cells
An accelerated test using a contaminated layer reveals how Si impurities accumulate at the Ni/YSZ electrode. High local overpotential and steam partial pressure are shown to drive the deposition of SiO 2 at the TPBs and its subsequent electrochemical reduction into Ni particles.
- 9 December 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 13 (48) , 42166-42177
Unravelling the role of Si and Al impurities in Ni/YSZ fuel electrode degradation in solid oxide electrolysis cells
An accelerated test using a contaminated layer reveals how Si impurities accumulate at the Ni/YSZ electrode. High local overpotential and steam partial pressure are shown to drive the deposition of SiO 2 at the TPBs and its subsequent electrochemical reduction into Ni particles.
- Top Cited Papers
- 9 October 2020
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 370 (6513) , 186-+
Recent advances in solid oxide cell technology for electrolysis
Electrolysis feels the heat: Electricity infrastructure powered by sunlight and wind requires flexible storage capacity to compensate for the intermittency of these sources. In this context, Hauch et al. review progress in solid oxide electrolyzer technology to split water and/or carbon dioxide into chemical fuels. These devices, which rely on oxide conduction between cathode and anode, use nonprecious metals as catalysts and operate above 600°C, thereby benefiting from thermodynamic and kinetic efficiencies. The authors highlight recent optimizations of cell components as well as systems-level architecture. Science , this issue p. eaba6118
- 9 October 2020
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 370 (6513) , 186-+
Top Cited PapersRecent advances in solid oxide cell technology for electrolysis
Electrolysis feels the heat: Electricity infrastructure powered by sunlight and wind requires flexible storage capacity to compensate for the intermittency of these sources. In this context, Hauch et al. review progress in solid oxide electrolyzer technology to split water and/or carbon dioxide into chemical fuels. These devices, which rely on oxide conduction between cathode and anode, use nonprecious metals as catalysts and operate above 600°C, thereby benefiting from thermodynamic and kinetic efficiencies. The authors highlight recent optimizations of cell components as well as systems-level architecture. Science , this issue p. eaba6118
- 10 July 2019
- Published by The Electrochemical Society in ECS Transactions
- Vol. 91 (1) , 215-223
Progress in SOEC Development Activities at Haldor Topsøe
Haldor Topsoe considers SOEC as an enabling technology for the electrification of the chemical industry. Here, we present status updates on our two stepping stone projects, CO2 electrolysis for CO production and H2O electrolysis for biogas upgrading, as well as a roadmap for the electrification for production of ammonia. Compared to other electrolysis technologies, SOEC allows for the conversion of CO2 into useful chemicals at very high efficiencies and at a faradaic yield of 100%. Haldor Topsoe has commercialized the CO2 electrolysis technology under the tradename eCOsTM: a platform for on-site, on-demand CO generation from CO2 feedstock. System-level synergies found in integrating the endothermal SOEC process with an exothermal chemical synthesis process can lead to very high conversion efficiencies. At a pilot plant located at Foulum, Denmark, H2 produced from steam by SOEC is used for upgrading CO2 in biogas into pipeline quality synthetic natural gas (SNG). It is Haldor Topsoe’s ambition to become a technology provider for electrified ammonia plants and a roadmap highlighting the key milestones towards SOEC + Haber-Bosch plants in 2030 will be presented.
- 10 July 2019
- Published by The Electrochemical Society in ECS Transactions
- Vol. 91 (1) , 215-223
Progress in SOEC Development Activities at Haldor Topsøe
Haldor Topsoe considers SOEC as an enabling technology for the electrification of the chemical industry. Here, we present status updates on our two stepping stone projects, CO2 electrolysis for CO production and H2O electrolysis for biogas upgrading, as well as a roadmap for the electrification for production of ammonia. Compared to other electrolysis technologies, SOEC allows for the conversion of CO2 into useful chemicals at very high efficiencies and at a faradaic yield of 100%. Haldor Topsoe has commercialized the CO2 electrolysis technology under the tradename eCOsTM: a platform for on-site, on-demand CO generation from CO2 feedstock. System-level synergies found in integrating the endothermal SOEC process with an exothermal chemical synthesis process can lead to very high conversion efficiencies. At a pilot plant located at Foulum, Denmark, H2 produced from steam by SOEC is used for upgrading CO2 in biogas into pipeline quality synthetic natural gas (SNG). It is Haldor Topsoe’s ambition to become a technology provider for electrified ammonia plants and a roadmap highlighting the key milestones towards SOEC + Haber-Bosch plants in 2030 will be presented.
- 10 July 2019
- Published by The Electrochemical Society in ECS Transactions
- Vol. 91 (1) , 2601-2611
Lifetime Capacity – An Important Performance Metric for SOEC Stacks
Haldor Topsoe has commercialized a system for on-site CO generation based on solid oxide electrolysis technology under a tradename eCOs™. A single eCOs™ module is capable of producing 96 Nm3 CO per hour at 99.5% purity, and larger units consisting of several modules and higher CO purities are available on demand. In this patented system, the electrochemical conversion of CO2 into CO is carried out in solid oxide electrolysis stacks. The parameters used to evaluate the performance of SOFC stacks typically include area-specific resistance (measured in Ω cm2 cell area), stack efficiency (measured in %), stack cost (e.g. USD/kW or USD/stack), degradation rate (typically measured in %V/1000 h), and stack lifetime (measured in hours). It is common practice in the field to use the above performance metrics also to describe stacks operating in SOEC mode. This manuscript will highlight how this practice may provide a skewed picture of stack performance, and that for the commercialization of SOEC technology, a number of additional performance metrics need to be considered. In particular, the importance of lifetime capacity, i.e. the total amount of product produced by a stack (measured e.g. in Nm3 gas or mol product per stack), is highlighted. Examples of alternative ways to maximize stack lifetime capacity will be described.
- 10 July 2019
- Published by The Electrochemical Society in ECS Transactions
- Vol. 91 (1) , 2601-2611
Lifetime Capacity – An Important Performance Metric for SOEC Stacks
Haldor Topsoe has commercialized a system for on-site CO generation based on solid oxide electrolysis technology under a tradename eCOs™. A single eCOs™ module is capable of producing 96 Nm3 CO per hour at 99.5% purity, and larger units consisting of several modules and higher CO purities are available on demand. In this patented system, the electrochemical conversion of CO2 into CO is carried out in solid oxide electrolysis stacks. The parameters used to evaluate the performance of SOFC stacks typically include area-specific resistance (measured in Ω cm2 cell area), stack efficiency (measured in %), stack cost (e.g. USD/kW or USD/stack), degradation rate (typically measured in %V/1000 h), and stack lifetime (measured in hours). It is common practice in the field to use the above performance metrics also to describe stacks operating in SOEC mode. This manuscript will highlight how this practice may provide a skewed picture of stack performance, and that for the commercialization of SOEC technology, a number of additional performance metrics need to be considered. In particular, the importance of lifetime capacity, i.e. the total amount of product produced by a stack (measured e.g. in Nm3 gas or mol product per stack), is highlighted. Examples of alternative ways to maximize stack lifetime capacity will be described.
- 1 July 2019
- Published by Elsevier in Solid State Ionics
- Vol. 335, 164-169
Influence of sintering profile on the microstructure and electronic transport properties of Sr(Ti,Nb)O3 tapes for solid oxide cell applications
- 1 July 2019
- Published by Elsevier in Solid State Ionics
- Vol. 335, 164-169
Influence of sintering profile on the microstructure and electronic transport properties of Sr(Ti,Nb)O3 tapes for solid oxide cell applications
- 1 February 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 378, 685-690
Reactivating the Ni-YSZ electrode in solid oxide cells and stacks by infiltration
- 1 February 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 378, 685-690
Reactivating the Ni-YSZ electrode in solid oxide cells and stacks by infiltration
- 1 January 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 373, 54-60
Carbon deposition and sulfur poisoning during CO2 electrolysis in nickel-based solid oxide cell electrodes
- 1 January 2018
- Published by Elsevier in Journal of Power Sources
- Vol. 373, 54-60
Carbon deposition and sulfur poisoning during CO2 electrolysis in nickel-based solid oxide cell electrodes
- 30 May 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 78 (1) , 2895-2905
Systematic Lifetime Testing of Stacks in CO2Electrolysis
Haldor Topsoe is commercializing a system for on-site CO generation based on solid oxide electrolysis technology (eCOs Plant). The standard system is capable of producing CO at 99.5% purity, but can also be customized to produce CO at 99.995% purity.In this patented system, the electrochemical conversion of CO2 into CO is carried out in solid oxide stacks, each stack producing approximately 1.5 Nm3 CO/h. In contrast to SOFC operation, the performance of a stack operating in electrolysis mode is not exclusively determined by the area-specific resistance (ASR). While resistance determines the overall efficiency of the stack, other parameters, such as the purity of the produced gas, can be more critical in a commercial system.A systematic approach to screening and evaluating stack and cell-level improvements is presented. Several stack tests were carried out for 2000 hours at a reference operating point and then intentionally stopped to evaluate the extent of degradation in stacks and to qualify/disqualify different design modifications. The described approach was used to significantly improve stack robustness and lifetime in CO2 electrolysis.Finally, some un-solved issues will be presented, in order to spur discussion on lifetime-limiting issues specific to electrolysis.
- 30 May 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 78 (1) , 2895-2905
Systematic Lifetime Testing of Stacks in CO2Electrolysis
Haldor Topsoe is commercializing a system for on-site CO generation based on solid oxide electrolysis technology (eCOs Plant). The standard system is capable of producing CO at 99.5% purity, but can also be customized to produce CO at 99.995% purity.In this patented system, the electrochemical conversion of CO2 into CO is carried out in solid oxide stacks, each stack producing approximately 1.5 Nm3 CO/h. In contrast to SOFC operation, the performance of a stack operating in electrolysis mode is not exclusively determined by the area-specific resistance (ASR). While resistance determines the overall efficiency of the stack, other parameters, such as the purity of the produced gas, can be more critical in a commercial system.A systematic approach to screening and evaluating stack and cell-level improvements is presented. Several stack tests were carried out for 2000 hours at a reference operating point and then intentionally stopped to evaluate the extent of degradation in stacks and to qualify/disqualify different design modifications. The described approach was used to significantly improve stack robustness and lifetime in CO2 electrolysis.Finally, some un-solved issues will be presented, in order to spur discussion on lifetime-limiting issues specific to electrolysis.
- 30 May 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 78 (1) , 2879-2884
eCOs - A Commercial CO2Electrolysis System Developed by Haldor Topsoe
This paper will cover the technical and commercial features of Haldor Topsoe’s CO from CO2 technology. Haldor Topsoe’s eCOs is a solid oxide electrolysis cell (SOEC) technology that allows the safe, efficient, and cost-competitive production of carbon monoxide directly at the site of facilities where the gas is needed. The CO-generation device uses feedstock carbon dioxide and electrical power to produce CO in quantities ideal for most operations that today rely on cylinder or tube trailer supply.An eCOs Plant is delivered as a stand-alone unit with power, CO2 and product gas connections. Furthermore, the plant ensures high levels of purity, producing CO at 99.5% assay with minimal contaminants and CO2 as the main impurity. An eCOs solution can also be customized to produce CO at 99.995% purity. One eCOs plant is able to deliver between 10 and 100 Nm3 CO gas per hour. Several plants can be operated in parallel if larger quantities are needed. The patented eCOs technology ensures security of supply, eliminates the need to transport hazardous gas, and drastically reduce costs related to storage, rentals and connections. In the longer run, this technology opens up for a whole new segment of green and sustainable chemicals from renewable carbon sources. Field test results from the 12-kW demonstration-unit located in Houston, Texas will be reported, as well as progress towards the 300-kW commercial unit to be delivered in 2018. Results from a 50-kW H2O electrolysis unit located in Foulum, Denmark used for biogas upgrading will also be presented.
- 30 May 2017
- Published by The Electrochemical Society in ECS Transactions
- Vol. 78 (1) , 2879-2884
eCOs - A Commercial CO2Electrolysis System Developed by Haldor Topsoe
This paper will cover the technical and commercial features of Haldor Topsoe’s CO from CO2 technology. Haldor Topsoe’s eCOs is a solid oxide electrolysis cell (SOEC) technology that allows the safe, efficient, and cost-competitive production of carbon monoxide directly at the site of facilities where the gas is needed. The CO-generation device uses feedstock carbon dioxide and electrical power to produce CO in quantities ideal for most operations that today rely on cylinder or tube trailer supply.An eCOs Plant is delivered as a stand-alone unit with power, CO2 and product gas connections. Furthermore, the plant ensures high levels of purity, producing CO at 99.5% assay with minimal contaminants and CO2 as the main impurity. An eCOs solution can also be customized to produce CO at 99.995% purity. One eCOs plant is able to deliver between 10 and 100 Nm3 CO gas per hour. Several plants can be operated in parallel if larger quantities are needed. The patented eCOs technology ensures security of supply, eliminates the need to transport hazardous gas, and drastically reduce costs related to storage, rentals and connections. In the longer run, this technology opens up for a whole new segment of green and sustainable chemicals from renewable carbon sources. Field test results from the 12-kW demonstration-unit located in Houston, Texas will be reported, as well as progress towards the 300-kW commercial unit to be delivered in 2018. Results from a 50-kW H2O electrolysis unit located in Foulum, Denmark used for biogas upgrading will also be presented.
- 1 May 2017
- Published by Elsevier in Materials Research Bulletin
- Vol. 89, 232-244
Spinel-based coatings for metal supported solid oxide fuel cells
- 1 May 2017
- Published by Elsevier in Materials Research Bulletin
- Vol. 89, 232-244
Spinel-based coatings for metal supported solid oxide fuel cells