Jörg Zschetzsche
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jörg Zschetzsche has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Uwe Füssel
Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
7 shared publications - Johannes Koal
Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
6 shared publications - Christian Mathiszik
Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
5 shared publications - Hans Christian Schmale
Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
3 shared publications - Stefan Heilmann
Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
3 shared publications - Martin Baumgarten
Institute of Manufacturing Science and Engineering, Chair of Joining Technology and Assembly, Technische Universität Dresden, Dresden, Germany
2 shared publications
Latest Publications
- Open Access
- 17 July 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (10) , 2671-2682
Non-destructive characterization of resistance projection welded joints by ultrasonic and passive magnetic flux density testing
The weld of resistance projection welded joints is not visible from outside. Therefore, visual evaluation is restricted, and visual inspection is not possible at all. So far, the parameters of the welding process are monitored and controlled. In addition, the welds are periodically tested destructively to determine the quality of the welds. No industrial standard has yet been established in the field of non-destructive testing (NDT) for projection welded joints. This study focuses on NDT of projection welds using two different ultrasonic imaging inspection systems and the passive magnetic ux density testing (pMFT) method. The ultrasonic inspection systems commercially available and established in the field of NDT of spot welds. Both systems are originally designed for the NDT of spot welds and not for projection welds. Unlike the ultrasonic systems, the pMFT is still in laboratory status. The method has originally been developed to evaluate spot welds and is also used in this study to evaluate projection welds. The applicability of the investigated systems to projection welding is investigated in order to derive mandatory development steps to achieve reliable results. The pMFT method shows also good results for NDT of spot welds In this contribution, the measurement and evaluation concept of the three NDT systems for projection welded joints is presented. The NDT results are discussed in the context of the corresponding destructive results in terms of tensile forces and fracture areas. Advises for further development of all investigated systems are given.
- 17 July 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (10) , 2671-2682
Open AccessNon-destructive characterization of resistance projection welded joints by ultrasonic and passive magnetic flux density testing
The weld of resistance projection welded joints is not visible from outside. Therefore, visual evaluation is restricted, and visual inspection is not possible at all. So far, the parameters of the welding process are monitored and controlled. In addition, the welds are periodically tested destructively to determine the quality of the welds. No industrial standard has yet been established in the field of non-destructive testing (NDT) for projection welded joints. This study focuses on NDT of projection welds using two different ultrasonic imaging inspection systems and the passive magnetic ux density testing (pMFT) method. The ultrasonic inspection systems commercially available and established in the field of NDT of spot welds. Both systems are originally designed for the NDT of spot welds and not for projection welds. Unlike the ultrasonic systems, the pMFT is still in laboratory status. The method has originally been developed to evaluate spot welds and is also used in this study to evaluate projection welds. The applicability of the investigated systems to projection welding is investigated in order to derive mandatory development steps to achieve reliable results. The pMFT method shows also good results for NDT of spot welds In this contribution, the measurement and evaluation concept of the three NDT systems for projection welded joints is presented. The NDT results are discussed in the context of the corresponding destructive results in terms of tensile forces and fracture areas. Advises for further development of all investigated systems are given.
- Open Access
- 24 April 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (12) , 3231-3232
Correction: Study on precise weld diameter validations by comparing destructive testing methods in resistance spot welding
- 24 April 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (12) , 3231-3232
Open AccessCorrection: Study on precise weld diameter validations by comparing destructive testing methods in resistance spot welding
- Open Access
- 19 March 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (7) , 1825-1835
Study on precise weld diameter validations by comparing destructive testing methods in resistance spot welding
The torsion test is rarely used for resistance spot-welded joints since they are not subjected to torsion in applications. Normal, shear, and/or peel loads are usually the main stresses. Extensive scientific investigations in the context of Kunsmann’s dissertation date back more than 50 years. These investigations are still the basis of ISO 17653 and the German guideline DVS 2916-1. Recent scientific investigations only use torsion tests, but do not describe the reason for its use. A decisive advantage of the torsion test over the other standardized destructive testing methods lies in the types of fracture modes that occur and the properties of the fracture surfaces. Torsional loading results in either interfacial or button-pulled fracture modes. No material residues occur on the fracture surfaces for ductile and advanced high-strength steels. Hence, the measurement of weld diameter is achievable with minimal constraints, resulting in reduced variability and facilitating objective assessments of spot welds. This article delineates these attributes through a comparative analysis of various destructive testing methods employing statistical approaches. Additionally, the article expounds on the design concept of the developed rig for conducting torsion tests on spot welds.
- 19 March 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (7) , 1825-1835
Open AccessStudy on precise weld diameter validations by comparing destructive testing methods in resistance spot welding
The torsion test is rarely used for resistance spot-welded joints since they are not subjected to torsion in applications. Normal, shear, and/or peel loads are usually the main stresses. Extensive scientific investigations in the context of Kunsmann’s dissertation date back more than 50 years. These investigations are still the basis of ISO 17653 and the German guideline DVS 2916-1. Recent scientific investigations only use torsion tests, but do not describe the reason for its use. A decisive advantage of the torsion test over the other standardized destructive testing methods lies in the types of fracture modes that occur and the properties of the fracture surfaces. Torsional loading results in either interfacial or button-pulled fracture modes. No material residues occur on the fracture surfaces for ductile and advanced high-strength steels. Hence, the measurement of weld diameter is achievable with minimal constraints, resulting in reduced variability and facilitating objective assessments of spot welds. This article delineates these attributes through a comparative analysis of various destructive testing methods employing statistical approaches. Additionally, the article expounds on the design concept of the developed rig for conducting torsion tests on spot welds.
- Open Access
Magnetic Characterization of the Nugget Microstructure at Resistance Spot Welding
Conventional resistance spot welds are not visible from the outside. Therefore, it is not straightforward to evaluate the joint quality non-destructively. The pulse-echo method of manual ultrasonic is widely used for non-destructive testing. Another option is the passive magnetic flux density testing, which is being developed at Technische Universität Dresden, Germany. The spot weld is magnetized in the normal direction and the residual magnetic flux density is measured on top of the surface of the joint. This method is suitable for spot welds on typical car body steels. Previous investigations show that the magnetic properties of the materials influence the test result. In order to develop this new non-destructive testing method further, it is necessary to know the magnetic properties of the different microstructure regions of a spot weld. This article focuses on methods to measure and evaluate the magnetic properties of these regions, especially of the base material and the weld. Different measuring methods and approaches are presented and compared with each other. Based on the results, recommendations for future measurements for magnetic characterizations are given.
Open AccessMagnetic Characterization of the Nugget Microstructure at Resistance Spot Welding
Conventional resistance spot welds are not visible from the outside. Therefore, it is not straightforward to evaluate the joint quality non-destructively. The pulse-echo method of manual ultrasonic is widely used for non-destructive testing. Another option is the passive magnetic flux density testing, which is being developed at Technische Universität Dresden, Germany. The spot weld is magnetized in the normal direction and the residual magnetic flux density is measured on top of the surface of the joint. This method is suitable for spot welds on typical car body steels. Previous investigations show that the magnetic properties of the materials influence the test result. In order to develop this new non-destructive testing method further, it is necessary to know the magnetic properties of the different microstructure regions of a spot weld. This article focuses on methods to measure and evaluate the magnetic properties of these regions, especially of the base material and the weld. Different measuring methods and approaches are presented and compared with each other. Based on the results, recommendations for future measurements for magnetic characterizations are given.
- Open Access
- 30 September 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 123 (3-4) , 749-760
Electrode wear investigation of aluminium spot welding by motion overlay
The amount of aluminium sheets in future body-in-white concepts is still on the rise. There is a need for optimizing the joining techniques, caused by the different characteristics compared to the established steel components. Especially the electrode life for resistance spot welding as a reliable and established process needs to be improved. One reason for the short electrode life when welding aluminium is the insulating effect of the aluminium oxide layer. One possibility to reduce the electrode wear is the mechanical destruction of the oxide layer before the welding. This paper describes the influence of a translational and rotational electrode movement on the electrode wear. The oxide layer destruction is detected by resistance measurement. It could be shown that the destruction of the oxide layer already occurs at low movements. However, a homogeneous, large-area destruction is necessary for a wear reduction.
- 30 September 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 123 (3-4) , 749-760
Open AccessElectrode wear investigation of aluminium spot welding by motion overlay
The amount of aluminium sheets in future body-in-white concepts is still on the rise. There is a need for optimizing the joining techniques, caused by the different characteristics compared to the established steel components. Especially the electrode life for resistance spot welding as a reliable and established process needs to be improved. One reason for the short electrode life when welding aluminium is the insulating effect of the aluminium oxide layer. One possibility to reduce the electrode wear is the mechanical destruction of the oxide layer before the welding. This paper describes the influence of a translational and rotational electrode movement on the electrode wear. The oxide layer destruction is detected by resistance measurement. It could be shown that the destruction of the oxide layer already occurs at low movements. However, a homogeneous, large-area destruction is necessary for a wear reduction.
- Open Access
General Approach for Inline Electrode Wear Monitoring at Resistance Spot Welding
Electrodes for resistance spot welding inevitably wear out. In order to extend their service life, the tip-dressing process restores their original geometry. So far, however, the point in time for tip-dressing is mainly based on experience and not on process data. Therefore, this study aims to evaluate the in-situ or inline wear during the welding process without using additional sensors, and to base the timing for tip-dressing on continuous process monitoring, extending electrode life even further. Under laboratory conditions, electrode wear is analyzed by topographical measurements deepening the knowledge of the known main wear modes of resistance-spot-welding electrodes, mushrooming and plateau forming, and characterizing an electrode length delta over the number of spot welds. In general, electrode wear results in deformation of the electrode contact area, which influences process parameters and thereby weld quality. The conducted tests show correlation between this deformed contact area and the electrode length delta. The study shows that this electrode length delta is visible in actual process data, and can therefore be used as a criterion to characterize the wear of electrodes. Furthermore, this study gives reason to question commonly used spot-welding quality criteria and suggests different approaches, such as basing spot-welding quality on the possibility of nondestructive testing.
Open AccessGeneral Approach for Inline Electrode Wear Monitoring at Resistance Spot Welding
Electrodes for resistance spot welding inevitably wear out. In order to extend their service life, the tip-dressing process restores their original geometry. So far, however, the point in time for tip-dressing is mainly based on experience and not on process data. Therefore, this study aims to evaluate the in-situ or inline wear during the welding process without using additional sensors, and to base the timing for tip-dressing on continuous process monitoring, extending electrode life even further. Under laboratory conditions, electrode wear is analyzed by topographical measurements deepening the knowledge of the known main wear modes of resistance-spot-welding electrodes, mushrooming and plateau forming, and characterizing an electrode length delta over the number of spot welds. In general, electrode wear results in deformation of the electrode contact area, which influences process parameters and thereby weld quality. The conducted tests show correlation between this deformed contact area and the electrode length delta. The study shows that this electrode length delta is visible in actual process data, and can therefore be used as a criterion to characterize the wear of electrodes. Furthermore, this study gives reason to question commonly used spot-welding quality criteria and suggests different approaches, such as basing spot-welding quality on the possibility of nondestructive testing.
- Open Access
Performing an Indirect Coupled Numerical Simulation for Capacitor Discharge Welding of Aluminium Components
Capacitor discharge welding (CDW) for projection welding provides very high current pulses in extremely short welding times. This requires a quick follow up behaviour of the electrodes during the softening of the projection. The possibilities of experimental process investigations are strongly limited because of the covered contact zone and short process times. The Finite Element Method (FEM) allows highly resoluted analyses in time and space and is therefore a suitable tool for process characterization and optimization. To utilize this mean of optimization, an indirect multiphysical numerical model has been developed in Ansys Mechanical APDL. This model couples the physical environments of thermal–electric with structural analysis. It can master the complexity of large deformations, short current rise times and high temperature gradients. A typical ring projection has been chosen as the joining task. The selected aluminium alloys are EN-AW-6082 (ring projection) and EN-AW-5083 (sheet metal). This paper presents the investigated material data, the model design and the methodology for an indirect coupling of the thermal–electric with the structural physic. The electrical contact resistance is adapted to the measured voltage in the experiment. The limits of the model in Ansys Mechanical APDL are due to large mesh deformation and decreasing element stiffness. Further modelling possibilities, which can handle the limits, are described.
Open AccessPerforming an Indirect Coupled Numerical Simulation for Capacitor Discharge Welding of Aluminium Components
Capacitor discharge welding (CDW) for projection welding provides very high current pulses in extremely short welding times. This requires a quick follow up behaviour of the electrodes during the softening of the projection. The possibilities of experimental process investigations are strongly limited because of the covered contact zone and short process times. The Finite Element Method (FEM) allows highly resoluted analyses in time and space and is therefore a suitable tool for process characterization and optimization. To utilize this mean of optimization, an indirect multiphysical numerical model has been developed in Ansys Mechanical APDL. This model couples the physical environments of thermal–electric with structural analysis. It can master the complexity of large deformations, short current rise times and high temperature gradients. A typical ring projection has been chosen as the joining task. The selected aluminium alloys are EN-AW-6082 (ring projection) and EN-AW-5083 (sheet metal). This paper presents the investigated material data, the model design and the methodology for an indirect coupling of the thermal–electric with the structural physic. The electrical contact resistance is adapted to the measured voltage in the experiment. The limits of the model in Ansys Mechanical APDL are due to large mesh deformation and decreasing element stiffness. Further modelling possibilities, which can handle the limits, are described.