Hsin-Chieh Yu

In this paper two distinct methods for nickel oxide (NiO_xon) preparation were utilized to form the hole injection layer (HIL) and systematically compared with the conventional organic material poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) for quantum dots light emitting diodes (QLEDs) fabrication. Green QLED incorporating PEDOT:PSS exhibited a maximum luminance of 549,658 cd/m² and the lowest turn-on voltage of 2.25 V. In contrast, QLED employing NiO_x nanoparticles (NPs) as the HIL demonstrated a superior current efficiency of 30 cd/A, higher external quantum efficiency (EQE) of 13.19%, and a maximum luminance of 289,349 cd/m². The higher current efficiency observed in the NiO_x NPs/Poly-TPD hybrid device indicates that an appropriate NiO_x preparation route combined with a suitable HTL can effectively improve QLED efficiency.

Herein, a lucid meta-holographic approach leveraging geometric phase metasurfaces and photonic crystal surface-emitting lasers is presented. Such a straightforward technique inherently enables polarized structured light projection with opposite circular polarization states, effectively doubling the field of view for depth sensing applications. Furthermore, the innate polarization state of projected light provides enhanced resistance to environmental interference. To demonstrate the practical utility of this method, an integrated depth sensing system based on the geometric phase meta-hologram has been developed and successfully detects targets at an operating distance of 75 cm, paving the way for advanced 3D sensing applications in various fields.

High-entropy materials have attracted extensive attention as emerging electrode materials in various energy applications due to their flexible tunability, unusual outstanding activities, and cost-effectiveness using multiple earth-abundant elements. We introduce a novel high-entropy composite oxide with the five elements of Cu, Ni, Co, Fe, and Cr (HEO-3CNF) for use in the oxygen evolution reaction (OER) in electrocatalytic water splitting. HEO-3CNF is composed of two phases with a non-equimolar, deficient high-entropy spinel oxide of (Cu_0.2−xNi_0.2Co_0.2Fe_0.2Cr_0.2)₃O₄ and monoclinic copper oxide (CuO). Electrochemical impedance spectroscopy (EIS) with distribution of relaxation times (DRT) analysis validates that the HEO-3CNF-based electrode exhibits faster charge transfer than benchmark CuO. It results in improved OER performance with a lower overpotential at 10 mA/cm² and a Tafel slope than CuO (518.1 mV and 119.7 mV/dec versus 615.9 mV and 131.7 mV/dec, respectively) in alkaline conditions. This work may provide a general strategy for preparing novel, cost-effective, high-entropy electrodes for water splitting.

Solar light-driven hydrogen by photocatalytic water splitting over a semiconductor photoelectrode has been considered a promising green energy carrier. P-type semiconducting copper oxides (Cu₂O and CuO) have attracted remarkable attention as an efficient photocathode for photoelectrochemical (PEC) water splitting because of their high solar absorptivity and optical band gaps. In this study, CuO thin films were prepared using the sol-gel spin coating method to investigate the effects of aging time and layer dependency. Electrodeposition was also applied to fabricate Cu₂O thin films. Cu₂O thin films annealed at 300 °C are a hetero-phase system composed of Cu₂O and CuO, while those at 400 °C are fully oxidized to CuO. Thin films are characterized using atomic force microscopy (AFM), scanning electron microscopy (SEM), ultraviolet-visible spectroscopy (UV-VIS), Fourier transform infrared spectroscopy (FTIR), spectroscopic ellipsometry (SE), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman microscopy. The hetero-phase thin films increase the photoconversion efficiency compared to Cu₂O. Fully oxidized thin films annealed at 400 °C exhibit a higher efficiency than the hetero-phase thin film. We also verified that CuO thin films fabricated using electrodeposition show slightly higher efficiency than the spin coating method. The highest photocurrent of 1.1 mA/cm² at 0.10 V versus RHE was measured for the fully oxidized CuO thin film under one-sun AM1.5G illumination. This study demonstrates a practical method to fabricate durable thin films with efficient optical and photocatalytic properties.

The scalability of In₂Se₃, one of the phase change materials, is investigated. By depositing the material onto a nanopatterned substrate, individual In₂Se₃nanoclusters are confined in the nanosize pits with well-defined shape and dimension permitting the systematic study of the ultimate scaling limit of its use as a phase change memory element. In₂Se₃of progressively smaller volume is heated inside a transmission electron microscope operating in diffraction mode. The volume at which the amorphous-crystalline transition can no longer be observed is taken as the ultimate scaling limit, which is approximately 5 nm³for In₂Se₃. The physics for the existence of scaling limit is discussed. Using phase change memory elements in memory hierarchy is believed to reduce its energy consumption because they consume zero leakage power in memory cells. Therefore, the phase change memory applications are of great importance in terms of energy saving.