Kristofer Bölke
Research Subjects
Kristofer Bölke has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Anita Wedholm
SSAB Europe, SE-971 88 Luleå, Sweden
2 shared publications - Daniel Söderström
SSAB Europe, SE-971 88 Luleå, Sweden
2 shared publications - Fredrik Nyman
Linde Gas AB, SE-169 68 Solna, Sweden
2 shared publications - Katarina Lundkvist
Swerim AB, Box 812, SE-971 25 Luleå, Sweden
2 shared publications - Lennart Gustavsson
SSAB Europe, SE-971 88 Luleå, Sweden
2 shared publications - Sara Rosendahl
SWERIM, 97125 Lulea, Sweden
2 shared publications
Latest Publications
- Open Access
- 13 January 2025
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 211, 223-227
Using an advanced simulation tool for successful conversion of reheating furnace to full oxyfuel operation
Oxyfuel combustion complements decarbonization efforts by reducing the energy needs in high-temperature industries. Steel reheating furnaces are good candidates for full oxyfuel operation since this can lead to up to 30% energy savings. Linde uses an in-house tool to simulate reheating furnaces for airfuel to oxyfuel conversion. This paper follows a real customer case, starting with an airfuel simulation setup used to analyze the furnace, followed by oxyfuel simulations for burner design and energy savings estimations. These simulations lead to a successful installation of oxyfuel burners for the reheating furnace located at Ovako Imatra site. After the commissioning is completed, performance evaluation is done by comparing a reference airfuel operation period with an oxyfuel combustion period. Full oxyfuel conversion results in 27% energy savings for hot charge and high production rate periods thanks to significantly lower flue gas losses. Removing nitrogen from the oxidizer decreases the flue gas volume, reducing the total heat capacity of the off-gas stream. The savings are around 30% for cold charge and average production rate periods.
- 13 January 2025
- Published by Linkoping University Electronic Press in Swedish Aerospace Conference, FT2025
- Vol. 211, 223-227
Open AccessUsing an advanced simulation tool for successful conversion of reheating furnace to full oxyfuel operation
Oxyfuel combustion complements decarbonization efforts by reducing the energy needs in high-temperature industries. Steel reheating furnaces are good candidates for full oxyfuel operation since this can lead to up to 30% energy savings. Linde uses an in-house tool to simulate reheating furnaces for airfuel to oxyfuel conversion. This paper follows a real customer case, starting with an airfuel simulation setup used to analyze the furnace, followed by oxyfuel simulations for burner design and energy savings estimations. These simulations lead to a successful installation of oxyfuel burners for the reheating furnace located at Ovako Imatra site. After the commissioning is completed, performance evaluation is done by comparing a reference airfuel operation period with an oxyfuel combustion period. Full oxyfuel conversion results in 27% energy savings for hot charge and high production rate periods thanks to significantly lower flue gas losses. Removing nitrogen from the oxidizer decreases the flue gas volume, reducing the total heat capacity of the off-gas stream. The savings are around 30% for cold charge and average production rate periods.
- Open Access
OXYFINES Technique for Upgrading Zinc Containing Blast Furnace Sludge—Part 2: System Analysis
Integrating novel technology in production systems for the upgrading and further use of residual materials is a potential way of improving the resource efficiency. Assessing technology integration prospects, by performing system analysis, assists in the forecasting of effects and opportunities for different concepts. Based on pilot trials results, using Linde’s OXYFINES technique for upgrading zinc containing blast furnace sludge, a system analysis was performed on the prospects of integrating an OXYFINES concept in an iron and steel production route. The calculations were made based on one option for a full-scale OXYFINES concept for indicating the effects on the blast furnace zinc load, raw material consumption, energy use and carbon dioxide emissions from using the OXYFINES sinter product as a raw material in blast furnace ironmaking or in the basic oxygen furnace steelmaking. The summarised system analysis results showed that the most advantageous metallurgical, environmental, and economic potential was realised in the calculations of using the sinter in the basic oxygen furnace. However, the sinter was found as well suitable for use in the blast furnace when considering mainly the metallurgical and the economic effects.
Open AccessOXYFINES Technique for Upgrading Zinc Containing Blast Furnace Sludge—Part 2: System Analysis
Integrating novel technology in production systems for the upgrading and further use of residual materials is a potential way of improving the resource efficiency. Assessing technology integration prospects, by performing system analysis, assists in the forecasting of effects and opportunities for different concepts. Based on pilot trials results, using Linde’s OXYFINES technique for upgrading zinc containing blast furnace sludge, a system analysis was performed on the prospects of integrating an OXYFINES concept in an iron and steel production route. The calculations were made based on one option for a full-scale OXYFINES concept for indicating the effects on the blast furnace zinc load, raw material consumption, energy use and carbon dioxide emissions from using the OXYFINES sinter product as a raw material in blast furnace ironmaking or in the basic oxygen furnace steelmaking. The summarised system analysis results showed that the most advantageous metallurgical, environmental, and economic potential was realised in the calculations of using the sinter in the basic oxygen furnace. However, the sinter was found as well suitable for use in the blast furnace when considering mainly the metallurgical and the economic effects.
- Open Access
OXYFINES Technique for Upgrading Zinc Containing Blast Furnace Sludge—Part 1: Pilot Trials
In the Swedish steel industry, much work is put on further increasing the recycling and use of residual materials. However, blast furnace sludge is one residual which currently, despite its valuable contents of iron and carbon, is put on landfill or long-term storage due to its zinc content. Linde has developed the OXYFINES technique which is suitable for upgrading of fine particulate and zinc containing materials. The material is fed to the OXYFINES burner whereby its zinc content is vaporised to a generated dust phase whereas other non-gasifiable contents, such as iron, forms an oxidic sinter phase in the bottom of the reactor. The technique has proven a high degree of zinc separation, is relatively flexible and straightforward, and does not require sludge pre-treatment such as drying. Pilot set-up and trials, using the OXYFINES technique, were performed at Swerim’s research facility. In the trials, the effects from altering different process parameters were tested aiming to develop an optimal concept for upgrading the blast furnace sludge. The pilot trials’ results showed the required process settings to attain a high degree of zinc separation from the sludge, and to generate an iron oxide product, suitable for straightforward charging to the steelmaking process.
Open AccessOXYFINES Technique for Upgrading Zinc Containing Blast Furnace Sludge—Part 1: Pilot Trials
In the Swedish steel industry, much work is put on further increasing the recycling and use of residual materials. However, blast furnace sludge is one residual which currently, despite its valuable contents of iron and carbon, is put on landfill or long-term storage due to its zinc content. Linde has developed the OXYFINES technique which is suitable for upgrading of fine particulate and zinc containing materials. The material is fed to the OXYFINES burner whereby its zinc content is vaporised to a generated dust phase whereas other non-gasifiable contents, such as iron, forms an oxidic sinter phase in the bottom of the reactor. The technique has proven a high degree of zinc separation, is relatively flexible and straightforward, and does not require sludge pre-treatment such as drying. Pilot set-up and trials, using the OXYFINES technique, were performed at Swerim’s research facility. In the trials, the effects from altering different process parameters were tested aiming to develop an optimal concept for upgrading the blast furnace sludge. The pilot trials’ results showed the required process settings to attain a high degree of zinc separation from the sludge, and to generate an iron oxide product, suitable for straightforward charging to the steelmaking process.