Mengyao Cui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mengyao Cui has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Lixin Wang
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
5 shared publications - Min Guo
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
3 shared publications - Shixin Wang
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
3 shared publications - Yuanzhe Li
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
3 shared publications - Yue Wang
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
2 shared publications - Zhuoxuan Zheng
Institute of Microelectronics of the Chinese Academy of Sciences, Beijing 100029, China
2 shared publications
Latest Publications
- Open Access
- 14 July 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (7) , 913
A Low Mismatch Current Charge Pump Applied to Phase-Locked Loops
This paper presents a charge pump circuit with a wide output range and low current mismatch applied to phase-locked loops. In this designed structure, T-shaped analog switches are adopted to suppress the non-ideal effects of clock feedthrough, switching time mismatch, and charge injection. A source follower and current splitting circuits are proposed to improve the matching accuracy of the charging and discharging currents and reduce the current mismatch rate. A rail-to-rail high-gain amplifier with a negative feedback connection is introduced to suppress the charge-sharing effect of the charge pump. A cascode current mirror with a high output impedance is used to provide the charge and discharge currents for the charge pump, which not only improves the current accuracy of the charge pump but also increases the output voltage range. The proposed charge pump is designed and simulated based on a 65 nm CMOS process. The results show that when the power supply voltage is 1.2 V, the output current of the charge pump is 100 μA, the output voltage is in the range of 0.2~1 V, and the maximum current mismatch rate and current variation rate are only 0.21% and 1.4%, respectively.
- 14 July 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (7) , 913
Open AccessA Low Mismatch Current Charge Pump Applied to Phase-Locked Loops
This paper presents a charge pump circuit with a wide output range and low current mismatch applied to phase-locked loops. In this designed structure, T-shaped analog switches are adopted to suppress the non-ideal effects of clock feedthrough, switching time mismatch, and charge injection. A source follower and current splitting circuits are proposed to improve the matching accuracy of the charging and discharging currents and reduce the current mismatch rate. A rail-to-rail high-gain amplifier with a negative feedback connection is introduced to suppress the charge-sharing effect of the charge pump. A cascode current mirror with a high output impedance is used to provide the charge and discharge currents for the charge pump, which not only improves the current accuracy of the charge pump but also increases the output voltage range. The proposed charge pump is designed and simulated based on a 65 nm CMOS process. The results show that when the power supply voltage is 1.2 V, the output current of the charge pump is 100 μA, the output voltage is in the range of 0.2~1 V, and the maximum current mismatch rate and current variation rate are only 0.21% and 1.4%, respectively.
- Open Access
- 8 March 2023
- Published by MDPI AG in Electronics
- Vol. 12 (6) , 1285
A Low-Power, Fast-Transient FVF-Based Output-Capacitorless LDO with Push–Pull Buffer and Adaptive Resistance Unit
An output-capacitorless low-dropout regulator (LDO) with a push–pull buffer was presented in this paper. The proposed push–pull buffer was able to provide a large charge and discharge current to increase the slew rate at the gate of the power transistor effectively, thereby improving the transient response of this LDO. In addition, an adaptive resistance unit (ARU) was proposed to solve the right half-plane zero problem caused by Miller compensation to optimize the loop stability of the LDO. The proposed LDO was implemented in a 0.18-µm CMOS technology. Simulation results showed that the quiescent current of this LDO was only 16.1 µA. It regulated the output at 1.5 V from a 1.8 V supply, with a dropout voltage of 300 mV at the maximum output current of 50 mA. The maximum value of the voltage spike was 129 mV. Additionally, the recovery time of the LDO was 0.2 µs.
- 8 March 2023
- Published by MDPI AG in Electronics
- Vol. 12 (6) , 1285
Open AccessA Low-Power, Fast-Transient FVF-Based Output-Capacitorless LDO with Push–Pull Buffer and Adaptive Resistance Unit
An output-capacitorless low-dropout regulator (LDO) with a push–pull buffer was presented in this paper. The proposed push–pull buffer was able to provide a large charge and discharge current to increase the slew rate at the gate of the power transistor effectively, thereby improving the transient response of this LDO. In addition, an adaptive resistance unit (ARU) was proposed to solve the right half-plane zero problem caused by Miller compensation to optimize the loop stability of the LDO. The proposed LDO was implemented in a 0.18-µm CMOS technology. Simulation results showed that the quiescent current of this LDO was only 16.1 µA. It regulated the output at 1.5 V from a 1.8 V supply, with a dropout voltage of 300 mV at the maximum output current of 50 mA. The maximum value of the voltage spike was 129 mV. Additionally, the recovery time of the LDO was 0.2 µs.
- Open Access
- 16 November 2022
- Published by MDPI AG in Electronics
- Vol. 11 (22) , 3764
A Single-Event Burnout Hardened Super-Junction Trench SOI LDMOS with Additional Hole Leakage Paths
In this paper, a novel super-junction trench silicon-on-insulator laterally-diffused metal-oxide-semiconductor (SJT SOI LDMOS) power device with additional hole leakage paths to improve single-event burnout (SEB) performance under high liner energy transfer (LET) is proposed for the first time. The electrical characteristics and SEB performance of the proposed SJT SOI LDMOS are both enhanced effectively. The replacement of a lightly doped N drift region with a heavily doped P pillar and N pillar considerably improves the tradeoff between breakdown voltage (BVDS) and specific on-resistance (Ron,sp). Compared with the conventional trench SOI LDMOS (CT SOI LDMOS), the static figures of merit (FOM, BVDS2/Ron,sp) of the SJT SOI LDMOS increases by 239%. The SEB performance of the SJT SOI LDMOS is significantly improved as the holes induced by the heavy ion can be quickly absorbed to the trench source metal through the heavily doped P+ region and P buried region rather than the base resistor of the parasitic bipolar junction transistor (BJT). The SEB threshold voltage (VSEB) of the CT SOI LDMOS is 58 V (39% of the BVDS) and that of the SJT SOI LDMOS is up to 173 V (87% of the BVDS) at high LET of 1 pC/μm.
- 16 November 2022
- Published by MDPI AG in Electronics
- Vol. 11 (22) , 3764
Open AccessA Single-Event Burnout Hardened Super-Junction Trench SOI LDMOS with Additional Hole Leakage Paths
In this paper, a novel super-junction trench silicon-on-insulator laterally-diffused metal-oxide-semiconductor (SJT SOI LDMOS) power device with additional hole leakage paths to improve single-event burnout (SEB) performance under high liner energy transfer (LET) is proposed for the first time. The electrical characteristics and SEB performance of the proposed SJT SOI LDMOS are both enhanced effectively. The replacement of a lightly doped N drift region with a heavily doped P pillar and N pillar considerably improves the tradeoff between breakdown voltage (BVDS) and specific on-resistance (Ron,sp). Compared with the conventional trench SOI LDMOS (CT SOI LDMOS), the static figures of merit (FOM, BVDS2/Ron,sp) of the SJT SOI LDMOS increases by 239%. The SEB performance of the SJT SOI LDMOS is significantly improved as the holes induced by the heavy ion can be quickly absorbed to the trench source metal through the heavily doped P+ region and P buried region rather than the base resistor of the parasitic bipolar junction transistor (BJT). The SEB threshold voltage (VSEB) of the CT SOI LDMOS is 58 V (39% of the BVDS) and that of the SJT SOI LDMOS is up to 173 V (87% of the BVDS) at high LET of 1 pC/μm.
- Open Access
- 24 February 2022
- Published by MDPI AG in Electronics
- Vol. 11 (5) , 701
A Low-Power, Fast-Transient Output-Capacitorless LDO with Transient Enhancement Unit and Current Booster
With the wide application of advanced portable devices, output-capacitorless low dropout regulators (OCL-LDO) are receiving increasing attention. This paper presents a low quiescent current OCL-LDO with fast transient response. A transient enhancement unit (TEU) is proposed as the output voltage-spike detection circuit. It enhances the transient response by improving the slew-rate at the gate of the power transistor. In addition, a current booster (CB), which consists of a current subtractor and a non-linear current mirror, is designed to improve the slew-rate further. The current subtractor increases the transconductances of the differential-input transistors to obtain a large slewing current, while the non-linear current mirror further boosts the current with no extra quiescent current consumption. The simulated results show that the proposed OCL-LDO is capable of supplying 100 mA load current while consuming 10.3 μA quiescent current. It regulates the output at 1 V from a supply voltage ranging from 1.2 to 1.8 V. When the load current is stepped from 1 mA to 100 mA in 100 ns, the OCL-LDO has attained a settling time of 190 ns, and the output voltage undershoot and overshoot are controlled under 110 mV.
- 24 February 2022
- Published by MDPI AG in Electronics
- Vol. 11 (5) , 701
Open AccessA Low-Power, Fast-Transient Output-Capacitorless LDO with Transient Enhancement Unit and Current Booster
With the wide application of advanced portable devices, output-capacitorless low dropout regulators (OCL-LDO) are receiving increasing attention. This paper presents a low quiescent current OCL-LDO with fast transient response. A transient enhancement unit (TEU) is proposed as the output voltage-spike detection circuit. It enhances the transient response by improving the slew-rate at the gate of the power transistor. In addition, a current booster (CB), which consists of a current subtractor and a non-linear current mirror, is designed to improve the slew-rate further. The current subtractor increases the transconductances of the differential-input transistors to obtain a large slewing current, while the non-linear current mirror further boosts the current with no extra quiescent current consumption. The simulated results show that the proposed OCL-LDO is capable of supplying 100 mA load current while consuming 10.3 μA quiescent current. It regulates the output at 1 V from a supply voltage ranging from 1.2 to 1.8 V. When the load current is stepped from 1 mA to 100 mA in 100 ns, the OCL-LDO has attained a settling time of 190 ns, and the output voltage undershoot and overshoot are controlled under 110 mV.
- Open Access
- 7 November 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (21) , 7895
A New Split Gate Resurf Stepped Oxide UMOSFET Structure with High Doped Epitaxial Layer for Improving Figure of Merit (FOM)
The split gate resurf stepped oxide with highly doped epitaxial layer (HDSGRSO) UMOSFET has been proposed. The epitaxial layer of HDSGRSO u-shape metal oxide semiconductor field effect transistor (UMOSFET) has been divided into three parts: the upper epitaxial layer, the lower epitaxial layer and the middle epitaxial layer with higher doping concentration. The research shows that the reduced SURface field (RESURF) active has been enhanced due to the high doped epitaxial layer, which can modulate the electric field distribution and reduce the internal high electric field. Therefore, the HDGRSO UMOSFET has a higher breakdown voltage (BV), a lower on-state specific resistance (RSP) and a better figure of merit (FOM). According to the results of Technology Computer Aided Design (TCAD) simulations, the FOM (BV2/RSP) of HDSGRSO UMOSFET has been improved by 464%, and FOM (RSP × Qgd) of HDSGRSO UMOSFET has been reduced by 27.9% compared to the conventional structure, respectively, when the BV is 240 V. Furthermore, there is no extra special process required in this advanced fabrication procedure, which is relatively cost-effective and achievable.
- 7 November 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (21) , 7895
Open AccessA New Split Gate Resurf Stepped Oxide UMOSFET Structure with High Doped Epitaxial Layer for Improving Figure of Merit (FOM)
The split gate resurf stepped oxide with highly doped epitaxial layer (HDSGRSO) UMOSFET has been proposed. The epitaxial layer of HDSGRSO u-shape metal oxide semiconductor field effect transistor (UMOSFET) has been divided into three parts: the upper epitaxial layer, the lower epitaxial layer and the middle epitaxial layer with higher doping concentration. The research shows that the reduced SURface field (RESURF) active has been enhanced due to the high doped epitaxial layer, which can modulate the electric field distribution and reduce the internal high electric field. Therefore, the HDGRSO UMOSFET has a higher breakdown voltage (BV), a lower on-state specific resistance (RSP) and a better figure of merit (FOM). According to the results of Technology Computer Aided Design (TCAD) simulations, the FOM (BV2/RSP) of HDSGRSO UMOSFET has been improved by 464%, and FOM (RSP × Qgd) of HDSGRSO UMOSFET has been reduced by 27.9% compared to the conventional structure, respectively, when the BV is 240 V. Furthermore, there is no extra special process required in this advanced fabrication procedure, which is relatively cost-effective and achievable.