Pingzhi Fang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pingzhi Fang has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
Hui Yu
Shanghai Typhoon Institute of China Meteorological Administration Shanghai China
3 shared publications- Hui Yu
Shanghai Typhoon Institute of China Meteorological Administration Shanghai China
3 shared publications Jie Tang
Shanghai Typhoon Institute of China Meteorological Administration, Shanghai, China
3 shared publicationsXiaotu Lei
Shanghai Typhoon Institute of China Meteorological Administration, Shanghai, China
3 shared publicationsBingke Zhao
Shanghai Typhoon Institute of China Meteorological Administration Shanghai China
2 shared publicationsDan Wu
2 shared publications
Latest Publications
- Open Access
- 22 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7356
A Modified Inflow Turbulence Synthesis Method for Large Eddy Simulation: Application to Thermal Stratification Effects on Wind Loads of an Isolated Cubic Building
The variation in thermal stratifications significantly alter the distribution of the wind load on buildings. In this study, large eddy simulation (LES) was adopted to investigate this influence on an isolated cubic building. The thermally stratified turbulent inflow for LES was synthesized by a modified generation method, which combines equilibrium boundary conditions with empirical stability functions and integrates them into the Fluent inherent vortex method. The effectiveness of the present method was verified by comparison with corresponding wind tunnel test data under neutral stratification. The simulated wind load around an isolated cubic building was then compared across three thermal stratification conditions, including neutral, stable and unstable stratification. Compared with the neutral stratification, variations in temperature result in variations in the position and morphology of the horseshoe vortex location at the windward side and separation vortex at the top under stable and unstable stratifications, changing the distribution characteristics of wind pressure in those areas. On the leeward side, the wind pressure and its non-Gaussian characteristics under stable and unstable stratifications are enhanced due the variation in temperature. The extreme wind pressure coefficient at the bottom region of the leeward surfaces under the stable and unstable stratification increases by 1.38- and 1.50-fold, respectively.
- 22 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7356
Open AccessA Modified Inflow Turbulence Synthesis Method for Large Eddy Simulation: Application to Thermal Stratification Effects on Wind Loads of an Isolated Cubic Building
The variation in thermal stratifications significantly alter the distribution of the wind load on buildings. In this study, large eddy simulation (LES) was adopted to investigate this influence on an isolated cubic building. The thermally stratified turbulent inflow for LES was synthesized by a modified generation method, which combines equilibrium boundary conditions with empirical stability functions and integrates them into the Fluent inherent vortex method. The effectiveness of the present method was verified by comparison with corresponding wind tunnel test data under neutral stratification. The simulated wind load around an isolated cubic building was then compared across three thermal stratification conditions, including neutral, stable and unstable stratification. Compared with the neutral stratification, variations in temperature result in variations in the position and morphology of the horseshoe vortex location at the windward side and separation vortex at the top under stable and unstable stratifications, changing the distribution characteristics of wind pressure in those areas. On the leeward side, the wind pressure and its non-Gaussian characteristics under stable and unstable stratifications are enhanced due the variation in temperature. The extreme wind pressure coefficient at the bottom region of the leeward surfaces under the stable and unstable stratification increases by 1.38- and 1.50-fold, respectively.
- Open Access
- 30 January 2025
- Published by Wiley in Meteorological Applications
- Vol. 32 (1)
Incorporating zero‐plane displacement in roughness length estimation and exposure correction factor calculation
Exposure correction is necessary for removing the distortion effects induced by nonstandard local exposure in raw near‐ground wind speed datasets. The accurate calculation of the exposure correction factor () for wind speeds requires reliable input of the local aerodynamic roughness length (). In this study, we evaluate the performance of an formula suggested by the World Meteorological Organization and the estimation of based on gustiness model. The estimation of will be more reasonable if local zero‐plane displacement () is considered under rough terrain conditions. An empirical linear relationship is introduced, and the ratio is recommended for meteorological stations under rough terrain conditions in China coastline. The incorporation of into the formula suggested by the World Meteorological Organization is further performed. Sensitivity analyses indicate that the estimates and values are highly sensitive to factors such as mean wind duration, gust duration and anemometer height. Finally, we conducted case studies across 15 meteorological stations in China coastline, which revealed that our proposed method enhances the accuracy of both estimation and calculation in comparison to the existing models.
- 30 January 2025
- Published by Wiley in Meteorological Applications
- Vol. 32 (1)
Open AccessIncorporating zero‐plane displacement in roughness length estimation and exposure correction factor calculation
Exposure correction is necessary for removing the distortion effects induced by nonstandard local exposure in raw near‐ground wind speed datasets. The accurate calculation of the exposure correction factor () for wind speeds requires reliable input of the local aerodynamic roughness length (). In this study, we evaluate the performance of an formula suggested by the World Meteorological Organization and the estimation of based on gustiness model. The estimation of will be more reasonable if local zero‐plane displacement () is considered under rough terrain conditions. An empirical linear relationship is introduced, and the ratio is recommended for meteorological stations under rough terrain conditions in China coastline. The incorporation of into the formula suggested by the World Meteorological Organization is further performed. Sensitivity analyses indicate that the estimates and values are highly sensitive to factors such as mean wind duration, gust duration and anemometer height. Finally, we conducted case studies across 15 meteorological stations in China coastline, which revealed that our proposed method enhances the accuracy of both estimation and calculation in comparison to the existing models.
- Open Access
- 1 September 2024
- Published by KEAI Publishing in Tropical Cyclone Research and Review
- Vol. 13 (3) , 161-174
A theoretical method to characterize the resistance effects of nonflat terrain on wind fields in a parametric wind field model for tropical cyclones
- 1 September 2024
- Published by KEAI Publishing in Tropical Cyclone Research and Review
- Vol. 13 (3) , 161-174
Open AccessA theoretical method to characterize the resistance effects of nonflat terrain on wind fields in a parametric wind field model for tropical cyclones
- Open Access
- 31 August 2024
- Published by KEAI Publishing in Tropical Cyclone Research and Review
- Vol. 13 (3) , 187-195
Study on the gust factors under onshore wind conditions based on the measurements from a coastal tower during three landfalling typhoons
Using high-frequency onshore wind data from four different heights of a coastal tower, the variations in gust factor with turbulence intensity, height and wind speed were studied under typhoon conditions. The gust factor increases with increasing turbulence intensity and, most often, can be described by a linear relationship with the turbulence intensity. The gust factor decreases with height and is relatively small compared with those presented in the national codes and other studies. A value of 2.5 is acceptable for the peak factor, which is close to the recommended value of the national code in China. The gust factor increases with increasing wind speed and is also affected by the wind direction. The gust factor has a value to that of previously published results when the wind flows roughly perpendicular to the shoreline, and has a smaller value when the wind flows roughly parallel to the shoreline. The phenomenon is caused by the confinement of shoreline on the sea wave development. Sea waves tend to propagate normal to the shoreline because of the refraction effect. As a result, a shorter roughness length exists in the parallel direction to the shoreline. It can be further explained by the weakness in the momentum flux exchange between the air and sea based on the wave form drag theory when the wind flows parallel to the shoreline.
- 31 August 2024
- Published by KEAI Publishing in Tropical Cyclone Research and Review
- Vol. 13 (3) , 187-195
Open AccessStudy on the gust factors under onshore wind conditions based on the measurements from a coastal tower during three landfalling typhoons
Using high-frequency onshore wind data from four different heights of a coastal tower, the variations in gust factor with turbulence intensity, height and wind speed were studied under typhoon conditions. The gust factor increases with increasing turbulence intensity and, most often, can be described by a linear relationship with the turbulence intensity. The gust factor decreases with height and is relatively small compared with those presented in the national codes and other studies. A value of 2.5 is acceptable for the peak factor, which is close to the recommended value of the national code in China. The gust factor increases with increasing wind speed and is also affected by the wind direction. The gust factor has a value to that of previously published results when the wind flows roughly perpendicular to the shoreline, and has a smaller value when the wind flows roughly parallel to the shoreline. The phenomenon is caused by the confinement of shoreline on the sea wave development. Sea waves tend to propagate normal to the shoreline because of the refraction effect. As a result, a shorter roughness length exists in the parallel direction to the shoreline. It can be further explained by the weakness in the momentum flux exchange between the air and sea based on the wave form drag theory when the wind flows parallel to the shoreline.
- Open Access
- 1 April 2020
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 199
A parametric wind field model and its application in simulating historical typhoons in the western North Pacific Ocean
- 1 April 2020
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 199
Open AccessA parametric wind field model and its application in simulating historical typhoons in the western North Pacific Ocean
- 1 April 2020
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 59 (4) , 637-650
Variations in Friction Velocity with Wind Speed and Height for Moderate-to-Strong Onshore Winds Based on Measurements from a Coastal Tower
Variations in friction velocity with wind speed and height are studied under moderate (≥9 m s−1)-to-strong onshore wind conditions caused by three landfalling typhoons. Wind data are from a coastal 100-m tower equipped with 20-Hz ultrasonic anemometers at three heights. Results show that wind direction affects variations in friction velocity with wind speed. A leveling off or decrease in friction velocity occurs at a critical wind speed of ~20 m s−1under strong onshore wind conditions. Friction velocity does not always decrease with height in the surface layer under typhoon conditions. Thus, height-based corrections on friction velocities using the model from Anctil and Donelan may not be reliable. Surface-layer heights predicted by the model that are based on Ekman dynamics are verified by comparing with those determined by a proposed method that is based on the idea of mean boundary layer using wind-profile data from one of the landfalling typhoons. Friction velocity at the top of the surface layer is then estimated. Results show that friction velocity decreases by about 20% from its surface value and agrees well with previous results of Tennekes.
- 1 April 2020
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 59 (4) , 637-650
Variations in Friction Velocity with Wind Speed and Height for Moderate-to-Strong Onshore Winds Based on Measurements from a Coastal Tower
Variations in friction velocity with wind speed and height are studied under moderate (≥9 m s−1)-to-strong onshore wind conditions caused by three landfalling typhoons. Wind data are from a coastal 100-m tower equipped with 20-Hz ultrasonic anemometers at three heights. Results show that wind direction affects variations in friction velocity with wind speed. A leveling off or decrease in friction velocity occurs at a critical wind speed of ~20 m s−1under strong onshore wind conditions. Friction velocity does not always decrease with height in the surface layer under typhoon conditions. Thus, height-based corrections on friction velocities using the model from Anctil and Donelan may not be reliable. Surface-layer heights predicted by the model that are based on Ekman dynamics are verified by comparing with those determined by a proposed method that is based on the idea of mean boundary layer using wind-profile data from one of the landfalling typhoons. Friction velocity at the top of the surface layer is then estimated. Results show that friction velocity decreases by about 20% from its surface value and agrees well with previous results of Tennekes.
- 11 November 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 705-720
Numerical and experimental study of the aerodynamic characteristics around two-dimensional terrain with different slope angles
- 11 November 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 705-720
Numerical and experimental study of the aerodynamic characteristics around two-dimensional terrain with different slope angles
- 25 October 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 848-858
Numerical investigation of the wind environment around tall buildings in a central business district
- 25 October 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 848-858
Numerical investigation of the wind environment around tall buildings in a central business district
- 24 August 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 744-757
Impact of physical representations in CALMET on the simulated wind field over land during Super Typhoon Meranti (2016)
- 24 August 2019
- Published by Springer Nature in Frontiers of Earth Science
- Vol. 13 (4) , 744-757
Impact of physical representations in CALMET on the simulated wind field over land during Super Typhoon Meranti (2016)
- Open Access
- 27 July 2018
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 123 (14) , 7340-7353
Effects of Wind Direction on Variations in Friction Velocity With Wind Speed Under Conditions of Strong Onshore Wind
The effects of wind direction on variations in friction velocity with wind speed are studied under moderate (≥9 m/s) to strong (≥22 m/s) onshore wind conditions using 20‐Hz ultrasonic wind data from a coastal tower at three different heights. The effects of different averaging time intervals of 20, 10, 2, and 1 min on the variations are also investigated. Three typhoons passed by the tower during the 150 hr of observations. Regardless of wind direction, friction velocity increases with increasing wind speed, and linear regression shows that the rate of increase is ~50% less than previously reported. However, a leveling‐off or decrease in friction velocity with increasing wind speed is found under strong wind conditions using a bin‐averaged method. Wind direction affects the variations in friction velocity with wind speed. Friction velocity increases with increasing wind speed at a similar growth rate to that of previously published results, with a leveling‐off or decrease at wind speeds higher than 22 m/s when the wind blows roughly normal to the shoreline. Form drag induced by sea waves with longer wavelengths is suggested to be responsible for the effects of wind direction on the variations in friction velocity with wind speed. An averaging time interval of 1 min yields representative variations in friction velocity with wind speed using the observations described in this study.
- 27 July 2018
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Atmospheres
- Vol. 123 (14) , 7340-7353
Open AccessEffects of Wind Direction on Variations in Friction Velocity With Wind Speed Under Conditions of Strong Onshore Wind
The effects of wind direction on variations in friction velocity with wind speed are studied under moderate (≥9 m/s) to strong (≥22 m/s) onshore wind conditions using 20‐Hz ultrasonic wind data from a coastal tower at three different heights. The effects of different averaging time intervals of 20, 10, 2, and 1 min on the variations are also investigated. Three typhoons passed by the tower during the 150 hr of observations. Regardless of wind direction, friction velocity increases with increasing wind speed, and linear regression shows that the rate of increase is ~50% less than previously reported. However, a leveling‐off or decrease in friction velocity with increasing wind speed is found under strong wind conditions using a bin‐averaged method. Wind direction affects the variations in friction velocity with wind speed. Friction velocity increases with increasing wind speed at a similar growth rate to that of previously published results, with a leveling‐off or decrease at wind speeds higher than 22 m/s when the wind blows roughly normal to the shoreline. Form drag induced by sea waves with longer wavelengths is suggested to be responsible for the effects of wind direction on the variations in friction velocity with wind speed. An averaging time interval of 1 min yields representative variations in friction velocity with wind speed using the observations described in this study.