Mushtaq F. Almensoury
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mushtaq F. Almensoury has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Atheer Saad Hashim
Department of Water Resources Management Engineering, College of Engineering Al‐Qasim Green University Babylon Iraq
2 shared publications - Farooq Hassan Ali
Mechanical Engineering Department, College of Engineering, University of Babylon
2 shared publications - Hameed Kadhem Hamzah
Mechanical Engineering Department, College of Engineering, University of Babylon
2 shared publications - Ahmed M. Hassan
Department of Mechanical Engineering University of Al‐Qadisiyah Al‐Qadisiyah Iraq
1 shared publication - Mohammad Ghalambaz
Department of Mathematics, Saveetha School of Engineering, SIMATS
1 shared publication Qusay Rasheed Al-Amir
1 shared publication
Latest Publications
- Open Access
- 23 July 2026
- Published by Elsevier in Next Energy
- Vol. 13
CPU thermal management using nano-encapsulated phase change material: Numerical investigation of orientation and magnetic field effects on heat transfer and entropy generation
- 23 July 2026
- Published by Elsevier in Next Energy
- Vol. 13
Open AccessCPU thermal management using nano-encapsulated phase change material: Numerical investigation of orientation and magnetic field effects on heat transfer and entropy generation
- 1 January 2021
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 7 (1) , 190-203
MULTISCALE APPROACH OF THE EQUIVALENT THERMAL CONDUCTIVITY OF MODIFIED FOAM-FILLED AND NON-FILLED HOLLOW BRICK AND A BRICK WALL
The energy loss through building components resulting in higher energy consumption, thus energy saving has become an essential aspect in design and comfort. This study aims to optimize the thermal insulation of red clay bricks used in the walls of buildings by using a multiscale method. The finite element approach in ABAQUS software has been used to simulate the bricks under different configurations and conditions. Due to cost and time challenges and difficulties in simulation and complex calculations, simplified and applicable equations have been derived to calculate thermal insulation properties. The results show that the paper’s brick design has a significant thermal conductivity reduction that could reach more than one-third of the other corresponding studies. The study goes to fill the hollow bricks by the insulation polyurethane foam (PUF) and comparing the results with air hollow bricks. Besides its other advantages, the outcomes reveal that using the PUF has a noticeable desired-influence in thermal insulation when considering the heat transfer by convection and radiation inside the air cavity of bricks.
- 1 January 2021
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 7 (1) , 190-203
MULTISCALE APPROACH OF THE EQUIVALENT THERMAL CONDUCTIVITY OF MODIFIED FOAM-FILLED AND NON-FILLED HOLLOW BRICK AND A BRICK WALL
The energy loss through building components resulting in higher energy consumption, thus energy saving has become an essential aspect in design and comfort. This study aims to optimize the thermal insulation of red clay bricks used in the walls of buildings by using a multiscale method. The finite element approach in ABAQUS software has been used to simulate the bricks under different configurations and conditions. Due to cost and time challenges and difficulties in simulation and complex calculations, simplified and applicable equations have been derived to calculate thermal insulation properties. The results show that the paper’s brick design has a significant thermal conductivity reduction that could reach more than one-third of the other corresponding studies. The study goes to fill the hollow bricks by the insulation polyurethane foam (PUF) and comparing the results with air hollow bricks. Besides its other advantages, the outcomes reveal that using the PUF has a noticeable desired-influence in thermal insulation when considering the heat transfer by convection and radiation inside the air cavity of bricks.
- 22 October 2020
- Published by Wiley in Heat Transfer
- Vol. 50 (3) , 2403-2426
Numerical investigation of natural convection of a non‐Newtonian nanofluid in an F‐shaped porous cavity
This study numerically investigates the free convective heat transfer of a non‐Newtonian nanofluid through an F‐shaped porous cavity. The thermal conditions of the walls of the cavity are assigned as TC and TH for the cold right wall and the hot left wall, respectively, and the remaining walls of the cavity are assigned as insulated walls. The model for this investigation is designed, implemented, and analyzed by COMSOL Multiphysics. The Galerkin finite element method is used to model and solve the governing equations of the flow and heat transfer process inside the porous media. Physical parameters are presented in the following order: and . The goal of this study is to study the influence of geometry configuration (F shape) and the above parameters on the flow structure, isotherms, and heat transfer. These parameters have been taken into account to investigate their effects on this kind of heat transfer mechanism. Results show that the addition of nanoparticles plays a significant role in changing heat transfer rates. In addition, an increase in the aspect ratio (AR) leads to create narrow areas, which promotes the stagnation zones, thus decreasing the distance between cold and hot walls. This, in turn, enhances the flow uniformity. Moreover, it has been generally concluded that the Nusselt number and velocity rates are directly proportional to the AR, Darcy number (Da), and Rayleigh number (Ra), and negatively proportional to the power‐law index (); however, there are some exceptions and unusual behaviors noticed and explained through the paper.
- 22 October 2020
- Published by Wiley in Heat Transfer
- Vol. 50 (3) , 2403-2426
Numerical investigation of natural convection of a non‐Newtonian nanofluid in an F‐shaped porous cavity
This study numerically investigates the free convective heat transfer of a non‐Newtonian nanofluid through an F‐shaped porous cavity. The thermal conditions of the walls of the cavity are assigned as TC and TH for the cold right wall and the hot left wall, respectively, and the remaining walls of the cavity are assigned as insulated walls. The model for this investigation is designed, implemented, and analyzed by COMSOL Multiphysics. The Galerkin finite element method is used to model and solve the governing equations of the flow and heat transfer process inside the porous media. Physical parameters are presented in the following order: and . The goal of this study is to study the influence of geometry configuration (F shape) and the above parameters on the flow structure, isotherms, and heat transfer. These parameters have been taken into account to investigate their effects on this kind of heat transfer mechanism. Results show that the addition of nanoparticles plays a significant role in changing heat transfer rates. In addition, an increase in the aspect ratio (AR) leads to create narrow areas, which promotes the stagnation zones, thus decreasing the distance between cold and hot walls. This, in turn, enhances the flow uniformity. Moreover, it has been generally concluded that the Nusselt number and velocity rates are directly proportional to the AR, Darcy number (Da), and Rayleigh number (Ra), and negatively proportional to the power‐law index (); however, there are some exceptions and unusual behaviors noticed and explained through the paper.