Hiroyasu Kifune
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hiroyasu Kifune has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Yoshihiro Hatanaka
Marine Technology Department, Tokyo University of Marine Science and Technology, 2–1-6, Etchujima, Koto-ku, Tokyo 135-8533, Japan
12 shared publicationsDaichi Yoshida
3 shared publications- Hiroaki Torii
Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and of Technology, Koto, Japan
2 shared publications Kohei Takashima
2 shared publicationsMasahiro Komatsu
2 shared publicationsMutsuo Nakaoka
2 shared publications
Latest Publications
- Open Access
- 19 July 2025
- Published by University of Split, Faculty of Maritime Studies in Transactions on Maritime Science
- Vol. 14 (02)
A Method for Estimating the Fuel Consumption Characteristics of Small Boats Sailing in Medium to High-Speed Range
This study aims to develop an application software to support energy-efficient operation for small boats of less than 20 tons. In order to develop this system, statistical surveys have been conducted on the relationship between ship speed, engine speed, and fuel consumption on a 19-ton small boat for several years. As a result, it was confirmed that fuel consumption does not necessarily increase monotonically with an increase in ship speed. Authors considered that this phenomenon can be utilised for saving fuel consumption in small boats effectively. In order to realise it, it is required to identify fuel consumption trends and compare the trends with the observed data. However, fuel consumption trends are affected by hull fouling, load weight and trim balance. For this reason, fuel consumption trend needs to be determined for each voyage. For the convenience of boat operators, it is desirable that fuel consumption trends are estimated by an easy, simple, and cost-effective method as soon as possible after leaving the port. The method proposed in the previous study was highly accurate, but it was not convenient due to two problems. This study proposes a new method for estimating fuel consumption trends that solves these issues. In order to develop a new estimation method, this study focuses on the hull frictional resistance. It was assumed that the effect of wave-making resistance on energy consumption in small boats saturates at medium to high speeds, and frictional resistance becomes the dominant factor. Thus, the fuel consumption trend of the boat was analysed on the assumption that it follows a fundamental physical law proportional to the cube of the ship's speed. Based on these assumptions, this study developed a new equation model that expresses the fuel consumption trend of small boats sailing in medium to high-speed range. The fuel consumption trend determined with the new model achieved proper performance. In addition, the method of estimating the fuel consumption trend using this model solves the two problems of the method of previous study.
- 19 July 2025
- Published by University of Split, Faculty of Maritime Studies in Transactions on Maritime Science
- Vol. 14 (02)
Open AccessA Method for Estimating the Fuel Consumption Characteristics of Small Boats Sailing in Medium to High-Speed Range
This study aims to develop an application software to support energy-efficient operation for small boats of less than 20 tons. In order to develop this system, statistical surveys have been conducted on the relationship between ship speed, engine speed, and fuel consumption on a 19-ton small boat for several years. As a result, it was confirmed that fuel consumption does not necessarily increase monotonically with an increase in ship speed. Authors considered that this phenomenon can be utilised for saving fuel consumption in small boats effectively. In order to realise it, it is required to identify fuel consumption trends and compare the trends with the observed data. However, fuel consumption trends are affected by hull fouling, load weight and trim balance. For this reason, fuel consumption trend needs to be determined for each voyage. For the convenience of boat operators, it is desirable that fuel consumption trends are estimated by an easy, simple, and cost-effective method as soon as possible after leaving the port. The method proposed in the previous study was highly accurate, but it was not convenient due to two problems. This study proposes a new method for estimating fuel consumption trends that solves these issues. In order to develop a new estimation method, this study focuses on the hull frictional resistance. It was assumed that the effect of wave-making resistance on energy consumption in small boats saturates at medium to high speeds, and frictional resistance becomes the dominant factor. Thus, the fuel consumption trend of the boat was analysed on the assumption that it follows a fundamental physical law proportional to the cube of the ship's speed. Based on these assumptions, this study developed a new equation model that expresses the fuel consumption trend of small boats sailing in medium to high-speed range. The fuel consumption trend determined with the new model achieved proper performance. In addition, the method of estimating the fuel consumption trend using this model solves the two problems of the method of previous study.
- Open Access
- 6 March 2024
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 29 (2) , 490
Correction to: Influence of propeller fouling on propulsion performance of an actual ship: a long-term analysis focusing on the power for keeping propeller’s rotation of a controllable pitch propeller
- 6 March 2024
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 29 (2) , 490
Open AccessCorrection to: Influence of propeller fouling on propulsion performance of an actual ship: a long-term analysis focusing on the power for keeping propeller’s rotation of a controllable pitch propeller
- Open Access
- 28 October 2023
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 28 (4) , 876-888
Influence of propeller fouling on propulsion performance of an actual ship: a long-term analysis focusing on the power for keeping propeller’s rotation of a controllable pitch propeller
This study focuses on the shaft power at the neutral angle of a controllable pitch propeller to analyze the change in the required power due to propeller fouling. It is named and defined as a power for keeping propeller’s rotation (RP) because a propeller does not generate the net thrust to push the hull but dissipates the power to keep its constant speed. Statistical analysis was conducted using a decade of the observed data from a research vessel. This study assumed that the change in RP can be considered as an indicator showing the state of propeller fouling. In addition, the state of fouling on the hull can be estimated indirectly based on RP because the data correlated the shaft power under several operating conditions with RP on the same voyage. The fouling state was classified into three conditions based on RP. The comparison of shaft power at the same ship speed between the clean condition and the serious fouled condition showed that the shaft power was increased by 35% on average due to fouling. When the ship navigates under 10 knots, propeller fouling has a larger impact on the increase in shaft power than hull fouling.
- 28 October 2023
- Published by Springer Nature in Journal of Marine Science and Technology
- Vol. 28 (4) , 876-888
Open AccessInfluence of propeller fouling on propulsion performance of an actual ship: a long-term analysis focusing on the power for keeping propeller’s rotation of a controllable pitch propeller
This study focuses on the shaft power at the neutral angle of a controllable pitch propeller to analyze the change in the required power due to propeller fouling. It is named and defined as a power for keeping propeller’s rotation (RP) because a propeller does not generate the net thrust to push the hull but dissipates the power to keep its constant speed. Statistical analysis was conducted using a decade of the observed data from a research vessel. This study assumed that the change in RP can be considered as an indicator showing the state of propeller fouling. In addition, the state of fouling on the hull can be estimated indirectly based on RP because the data correlated the shaft power under several operating conditions with RP on the same voyage. The fouling state was classified into three conditions based on RP. The comparison of shaft power at the same ship speed between the clean condition and the serious fouled condition showed that the shaft power was increased by 35% on average due to fouling. When the ship navigates under 10 knots, propeller fouling has a larger impact on the increase in shaft power than hull fouling.
- Open Access
- 23 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 195541-195550
Efficiency Estimation of Synchronous Generators for Marine Applications and Verification With Shop Trial Data and Real Ship Operation Data
Three methods were explored to estimate the efficiency for the conversion of mechanical power to electrical power using synchronous generators in ships at low power factors. Generally, the generator efficiency data is provided by manufacturers as shop trial data and is measured by operating generators under power factor of 0.8 and 1.0. However, the efficiency of synchronous generators is not measured under low power factor of less than 0.8. In practice, onboard generators occasionally operate at low power factor and it is desirable to clarify their characteristics for power system designers of large vessels. By substituting the shop trial data into the proposed efficiency estimation formulas, the generator efficiency at low power factor was extrapolated. To evaluate the validity of these methods, the fuel consumption characteristics of diesel engines as prime movers was focused. The estimation of the generator efficiency was indirectly validated using a statistical analysis of long-term observational data of the generator in operation. As a result, the efficiency estimation method based on a power loss mechanism gave the most reliable result among the three estimation methods. The root mean squared error of the calculated specific fuel consumption was 3.5 g/kWh, which is approximately 1.66 % error rate.
- 23 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 195541-195550
Open AccessEfficiency Estimation of Synchronous Generators for Marine Applications and Verification With Shop Trial Data and Real Ship Operation Data
Three methods were explored to estimate the efficiency for the conversion of mechanical power to electrical power using synchronous generators in ships at low power factors. Generally, the generator efficiency data is provided by manufacturers as shop trial data and is measured by operating generators under power factor of 0.8 and 1.0. However, the efficiency of synchronous generators is not measured under low power factor of less than 0.8. In practice, onboard generators occasionally operate at low power factor and it is desirable to clarify their characteristics for power system designers of large vessels. By substituting the shop trial data into the proposed efficiency estimation formulas, the generator efficiency at low power factor was extrapolated. To evaluate the validity of these methods, the fuel consumption characteristics of diesel engines as prime movers was focused. The estimation of the generator efficiency was indirectly validated using a statistical analysis of long-term observational data of the generator in operation. As a result, the efficiency estimation method based on a power loss mechanism gave the most reliable result among the three estimation methods. The root mean squared error of the calculated specific fuel consumption was 3.5 g/kWh, which is approximately 1.66 % error rate.
- 27 March 2019
- Published by Wiley in Electrical Engineering in Japan
- Vol. 207 (2) , 38-48
A coil layout of wireless power transfer systems based on multicoil arrangement for underwater vehicles
This paper proposes an optimal coil layout of wireless power transfer (WPT) systems for underwater vehicles (UVs). The power supply station adopts a multicoil arrangement with a double layer, and the UV also uses two receiving coils. The proposed WPT system for UVs has a reasonable advantage, where it does not request to adjust the relative position of coils. This paper experimentally discusses an optimal coil layout based on measurement results of a coupling coefficient. As a result, the proposed coil arrangement with the geometry rule realizes a certain power transfer under any positions and directions of UVs.
- 27 March 2019
- Published by Wiley in Electrical Engineering in Japan
- Vol. 207 (2) , 38-48
A coil layout of wireless power transfer systems based on multicoil arrangement for underwater vehicles
This paper proposes an optimal coil layout of wireless power transfer (WPT) systems for underwater vehicles (UVs). The power supply station adopts a multicoil arrangement with a double layer, and the UV also uses two receiving coils. The proposed WPT system for UVs has a reasonable advantage, where it does not request to adjust the relative position of coils. This paper experimentally discusses an optimal coil layout based on measurement results of a coupling coefficient. As a result, the proposed coil arrangement with the geometry rule realizes a certain power transfer under any positions and directions of UVs.
- 6 December 2012
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 7 (S1) , S167-S172
Optimal frequency tracking method for phase‐shift PWM inverter
- 6 December 2012
- Published by Wiley in IEEJ Transactions on Electrical and Electronic Engineering
- Vol. 7 (S1) , S167-S172
Optimal frequency tracking method for phase‐shift PWM inverter
- 1 January 2012
- Published by The Japan Institute of Marine Engineering in Marine Engineering
- Vol. 47 (2) , 243-248
Development of Diesel Particulate Filter Constructed from Nonwoven Fabric Metallic Fiber Filter Applying Induction Heating
Novel marine diesel particulate filter (DPF) which traps particulate matter (PM) exhausted from a marine diesel engine on the surface of a nonwoven fabric metallic filter has been developed. PM trapping characteristics in relation to the PM reduction ratio and pressure loss in the DPF unit have been investigated through experiments on a running diesel engine. Trapped PM was eliminated by high frequency induction heating, effectively regenerating the DPF. The experimental results which show the mutual relation between the pressure losses and PM reduction ratio in the DPF were investigated and estimated on the basis of the DPF unit’s construction.
- 1 January 2012
- Published by The Japan Institute of Marine Engineering in Marine Engineering
- Vol. 47 (2) , 243-248
Development of Diesel Particulate Filter Constructed from Nonwoven Fabric Metallic Fiber Filter Applying Induction Heating
Novel marine diesel particulate filter (DPF) which traps particulate matter (PM) exhausted from a marine diesel engine on the surface of a nonwoven fabric metallic filter has been developed. PM trapping characteristics in relation to the PM reduction ratio and pressure loss in the DPF unit have been investigated through experiments on a running diesel engine. Trapped PM was eliminated by high frequency induction heating, effectively regenerating the DPF. The experimental results which show the mutual relation between the pressure losses and PM reduction ratio in the DPF were investigated and estimated on the basis of the DPF unit’s construction.
- 1 January 2010
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 130 (10) , 1193-1194
Development of Marine Diesel Particulate Filter Using High frequency Induction Heating
- 1 January 2010
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 130 (10) , 1193-1194
Development of Marine Diesel Particulate Filter Using High frequency Induction Heating
- 1 January 2009
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 129 (10) , 1011-1012
Development of Frequency Doubler ZCS High Frequency Inverter
- 1 January 2009
- Published by Institute of Electrical Engineers of Japan (IEE Japan) in IEEJ Transactions on Industry Applications
- Vol. 129 (10) , 1011-1012
Development of Frequency Doubler ZCS High Frequency Inverter
- 1 January 2006
- Published by The Japan Institute of Marine Engineering in Marine Engineering
- Vol. 41 (6) , 889-894
Development of Marine Diesel Particulate Filter by means of High Frequency Induction Heating
- 1 January 2006
- Published by The Japan Institute of Marine Engineering in Marine Engineering
- Vol. 41 (6) , 889-894
Development of Marine Diesel Particulate Filter by means of High Frequency Induction Heating