A.E. Igbayeva
Research Subjects
Research Interests
A.E. Igbayeva has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Dinara Baskanbayeva
Institute of Power Engineering and Mechanical Engineering Named After A. Burkitbaev, Satbayev University, Almaty 040714, Kazakhstan
3 shared publications - Kassym Yelemessov
Institute of Power Engineering and Mechanical Engineering Named After A. Burkitbaev, Satbayev University, Almaty 040714, Kazakhstan
2 shared publications - Leonid Krupnik
Satbayev Univ, Inst Met & Ind Engn, Alma Ata 50013, Kazakhstan
2 shared publications - Dilda Nаuryzbayeva
Satbayev Univ, Alma Ata 50013, Kazakhstan
1 shared publication S.A Bortebayev
1 shared publication- S.A. Bortebayev
Kazakh National Research Technical University named after K.I.Satpayev
1 shared publication
Latest Publications
- 2 August 2022
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(207),p. 35-39
Investigation of the operation of centrifugal pump housings made of fiber concrete under the influence of a water-sand mixture
Целью данной работы является определение изностойкости композитных материалов. При соответствии физико-химических свойств композиционных материалов металлическим аналогам дает существенное преимущество по себестоимости, трудоемкости изготовления и ремонтных работах. В машиностроении одним из путей совершенствования конструкции является переход от стальных и чугунных корпусов к корпусам из легких сплавов (алюминиевых, магниевых), неметаллических или композиционных материалов, что особенно важно в изготовлении корпусных деталей центробежных насосов малой мощности. В таких корпусах толщина стенки, определяемая технологическими возможностями литья, больше толщины стенки, необходимой из условия прочности. The purpose of this work is to determine the wear resistance of composite materials. When the physicochemical properties of composite materials correspond to metal analogues, it gives a significant advantage in terms of cost, complexity of manufacturing and repair work. In mechanical engineering, one of the ways to improve the design is the transition from steel and cast-iron housings to housings made of light alloys (aluminum, magnesium), non-metallic or composite materials, which is especially important in the manufacture of housing parts of low-power centrifugal pumps. In such cases, the wall thickness determined by the technological capabilities of casting is greater than the wall thickness required from the strength condition.
- 2 August 2022
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(207),p. 35-39
Investigation of the operation of centrifugal pump housings made of fiber concrete under the influence of a water-sand mixture
Целью данной работы является определение изностойкости композитных материалов. При соответствии физико-химических свойств композиционных материалов металлическим аналогам дает существенное преимущество по себестоимости, трудоемкости изготовления и ремонтных работах. В машиностроении одним из путей совершенствования конструкции является переход от стальных и чугунных корпусов к корпусам из легких сплавов (алюминиевых, магниевых), неметаллических или композиционных материалов, что особенно важно в изготовлении корпусных деталей центробежных насосов малой мощности. В таких корпусах толщина стенки, определяемая технологическими возможностями литья, больше толщины стенки, необходимой из условия прочности. The purpose of this work is to determine the wear resistance of composite materials. When the physicochemical properties of composite materials correspond to metal analogues, it gives a significant advantage in terms of cost, complexity of manufacturing and repair work. In mechanical engineering, one of the ways to improve the design is the transition from steel and cast-iron housings to housings made of light alloys (aluminum, magnesium), non-metallic or composite materials, which is especially important in the manufacture of housing parts of low-power centrifugal pumps. In such cases, the wall thickness determined by the technological capabilities of casting is greater than the wall thickness required from the strength condition.
- Open Access
- 1 January 2020
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 5,p. 68-74
Justification of rational parameters for manufacturing pump housings made of fibroconcrete
Justification of rational parameters for manufacturing pump housings made of fibroconcrete
- 1 January 2020
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 5,p. 68-74
Open AccessJustification of rational parameters for manufacturing pump housings made of fibroconcrete
Justification of rational parameters for manufacturing pump housings made of fibroconcrete