Jihun Mun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jihun Mun has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Sang-Woo Kang
Strategic Technology Research Institute Korea Research Institute of Standards and Science Daejeon Republic of Korea
6 shared publications - Euna Jung
Strategic Technology Research Institute Korea Research Institute of Standards and Science Daejeon South Korea
5 shared publications - Jae-Hyun Lee
SKKU Advanced Institute of Nanotechnology (SAINT) Sungkyunkwan University Suwon South Korea
5 shared publications - Taesung Kim
SKKU Advanced Institute of Nanotechnology (SAINT) Sungkyunkwan University Suwon South Korea
5 shared publications - Jeongin Song
Strategic Technology Research Institute Korea Research Institute of Standards and Science Daejeon South Korea
4 shared publications - Byeonghyeon Min
Strategic Technology Research Institute, Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea
3 shared publications
Latest Publications
- Open Access
- 11 November 2026
- Published by Wiley in Advanced Materials Interfaces
Gap‐Filling Stencil Lithography for Precise and High Yield Patterning of Two‐Dimensional Materials
Two‐dimensional materials (2DMs) are considered revolutionary candidates for manufacturing electronics because of their atomically thin nature and exceptional electrical properties. Lithography is essential for patterning 2DMs and fabricating electronic devices. However, conventional water‐based processes such as photolithography fail to achieve high‐yield production because of 2DM delamination from the substrate. Although non‐water‐based stencil lithography is an alternative, the inherent gap between the mask and substrate causes blurring, obscuring high‐precision definition. In this study, we present gap‐filling stencil lithography (GSL), which introduces a protective layer to eliminate this gap, thereby suppressing blurring and enabling precise patterning for 2DMs. Pattern arrays fabricated through multialignment GSL achieved an exceptional 100% yield, compared to the 79.2% yield obtained through photolithography. GSL was implemented on various 2DMs to validate its universality, demonstrating repeatability by maintaining consistent dimensions after consecutive GSL cycles without mask degradation. Finally, the electrical performance of edge‐contact field‐effect transistors fabricated using GSL was evaluated, which confirms GSL as a practical approach to manufacture electronic devices utilizing 2DM. Consequently, this GSL method is expected to emerge as a promising patterning candidate for 2DM because it can overcome the critical processing vulnerabilities of conventional lithography to ensure high‐yield production.
- 11 November 2026
- Published by Wiley in Advanced Materials Interfaces
Open AccessGap‐Filling Stencil Lithography for Precise and High Yield Patterning of Two‐Dimensional Materials
Two‐dimensional materials (2DMs) are considered revolutionary candidates for manufacturing electronics because of their atomically thin nature and exceptional electrical properties. Lithography is essential for patterning 2DMs and fabricating electronic devices. However, conventional water‐based processes such as photolithography fail to achieve high‐yield production because of 2DM delamination from the substrate. Although non‐water‐based stencil lithography is an alternative, the inherent gap between the mask and substrate causes blurring, obscuring high‐precision definition. In this study, we present gap‐filling stencil lithography (GSL), which introduces a protective layer to eliminate this gap, thereby suppressing blurring and enabling precise patterning for 2DMs. Pattern arrays fabricated through multialignment GSL achieved an exceptional 100% yield, compared to the 79.2% yield obtained through photolithography. GSL was implemented on various 2DMs to validate its universality, demonstrating repeatability by maintaining consistent dimensions after consecutive GSL cycles without mask degradation. Finally, the electrical performance of edge‐contact field‐effect transistors fabricated using GSL was evaluated, which confirms GSL as a practical approach to manufacture electronic devices utilizing 2DM. Consequently, this GSL method is expected to emerge as a promising patterning candidate for 2DM because it can overcome the critical processing vulnerabilities of conventional lithography to ensure high‐yield production.
- Open Access
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
An analytical framework for humidity-dependence in polymer-polymer triboelectric nanogenerators
Humidity degrades the output of triboelectric nanogenerators (TENGs) by anything from a few tens of percent to more than two orders of magnitude, and no single material property accounts for that spread. We present an analytical framework for polymer contact-separation TENGs in which the relative humidity reaches the device output through two measurable material descriptors. We obtain the effective permittivity from a three-phase Bruggeman relation that splits sorbed water into a rotationally hindered bound population and a free one, so that the polymers taking up the most water are those in which most of it is dielectrically inactive. We then treat moisture as removing charge that has already separated rather than preventing its separation, and place that removal at contact, where a mobile water film on either facing surface short-circuits the two charged faces. How much charge is lost depends on whether the wetted regions connect: isolated patches that drain only their own footprint and a spanning film the whole contact. The wetted area belongs to the two faces together, so the threshold is a property of the pair, and only free multilayer water can bridge a contact, which holds the loss down through the drier half of the range. Applying the descriptors to sixteen polymer pairs, we find that the retention of open-circuit voltage between 10 % and 90 % RH spans 0.7 to 65 %, and that the ranking of the pairs inverts between dry and humid operation. Measurements on five pairs place the half-points at 56 to 75 % RH, against 57 to 77 % predicted.
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAn analytical framework for humidity-dependence in polymer-polymer triboelectric nanogenerators
Humidity degrades the output of triboelectric nanogenerators (TENGs) by anything from a few tens of percent to more than two orders of magnitude, and no single material property accounts for that spread. We present an analytical framework for polymer contact-separation TENGs in which the relative humidity reaches the device output through two measurable material descriptors. We obtain the effective permittivity from a three-phase Bruggeman relation that splits sorbed water into a rotationally hindered bound population and a free one, so that the polymers taking up the most water are those in which most of it is dielectrically inactive. We then treat moisture as removing charge that has already separated rather than preventing its separation, and place that removal at contact, where a mobile water film on either facing surface short-circuits the two charged faces. How much charge is lost depends on whether the wetted regions connect: isolated patches that drain only their own footprint and a spanning film the whole contact. The wetted area belongs to the two faces together, so the threshold is a property of the pair, and only free multilayer water can bridge a contact, which holds the loss down through the drier half of the range. Applying the descriptors to sixteen polymer pairs, we find that the retention of open-circuit voltage between 10 % and 90 % RH spans 0.7 to 65 %, and that the ranking of the pairs inverts between dry and humid operation. Measurements on five pairs place the half-points at 56 to 75 % RH, against 57 to 77 % predicted.
- Open Access
- 4 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (55) , e74470
Scalable Synthesis of 3D Hierarchical MoS 2 as a Durable, High‐Charge‐Retention Friction Layer for the Facile Fabrication of High‐Power Triboelectric Nanogenerators
Given the increasing demand for sustainable energy and self‐powered devices, energy‐harvesting technologies, such as triboelectric nanogenerators (TENGs), are drawing attention. To address the short charge retention in conventional polymer materials, 2D materials with high surface areas and intrinsic charge‐trapping capabilities, such as MoS 2 , are being utilized as friction layers in TENGs. However, their power generation is too low for practical applications owing to their atomically thin nature, limiting their use as fillers in polymer‐based systems. We report a 2D‐material‐based high‐power TENG using 3D hierarchical MoS 2 (3DH‐MoS 2 ) as a primary friction material. The 3DH‐MoS 2 is synthesized via low‐temperature metal–organic chemical vapor deposition, enabling the direct growth of a uniform, large‐area, 3D‐nanostructured friction layer on a polymer substrate without additional processes. This 3D nanostructure increases the amount of charge‐trapping sites and significantly enhances the durability of the device. The 4 × 4 cm 2 3DH‐MoS 2 ‐based TENG produces a maximum output voltage of 320.1 V and a power density of 0.841 mW cm −2 , proving it can effectively power light‐emitting diodes and a calculator, maintaining its performance over 10 000 cycles. In addition, the device can generate electricity from gas and water flow and human motion, highlighting the potential and versatility of 2D‐material‐based energy‐harvesting systems.
- 4 August 2026
- Published by Wiley in Advanced Materials
- Vol. 38 (55) , e74470
Open AccessScalable Synthesis of 3D Hierarchical MoS 2 as a Durable, High‐Charge‐Retention Friction Layer for the Facile Fabrication of High‐Power Triboelectric Nanogenerators
Given the increasing demand for sustainable energy and self‐powered devices, energy‐harvesting technologies, such as triboelectric nanogenerators (TENGs), are drawing attention. To address the short charge retention in conventional polymer materials, 2D materials with high surface areas and intrinsic charge‐trapping capabilities, such as MoS 2 , are being utilized as friction layers in TENGs. However, their power generation is too low for practical applications owing to their atomically thin nature, limiting their use as fillers in polymer‐based systems. We report a 2D‐material‐based high‐power TENG using 3D hierarchical MoS 2 (3DH‐MoS 2 ) as a primary friction material. The 3DH‐MoS 2 is synthesized via low‐temperature metal–organic chemical vapor deposition, enabling the direct growth of a uniform, large‐area, 3D‐nanostructured friction layer on a polymer substrate without additional processes. This 3D nanostructure increases the amount of charge‐trapping sites and significantly enhances the durability of the device. The 4 × 4 cm 2 3DH‐MoS 2 ‐based TENG produces a maximum output voltage of 320.1 V and a power density of 0.841 mW cm −2 , proving it can effectively power light‐emitting diodes and a calculator, maintaining its performance over 10 000 cycles. In addition, the device can generate electricity from gas and water flow and human motion, highlighting the potential and versatility of 2D‐material‐based energy‐harvesting systems.
- Open Access
- 8 June 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (59) , e31664
3D Hierarchical MoS 2 ‐Based Piezoresistive Pressure Sensors With Ultrahigh Sensitivity and Wide Dynamic Range
The rapid advancements in artificial intelligence, wearable devices, and the Internet of Things underscore the growing importance of sensor technology, particularly pressure sensors, for driving innovation across various fields. Wide‐dynamic‐range pressure sensors that exhibit high sensitivity without being biased toward a specific range are therefore needed. We propose an ultrahigh‐sensitivity, wide‐dynamic‐range pressure sensor that integrates 3D hierarchical (3DH) MoS 2 as the sensing material with a polymer cavity structure. 3DH MoS 2 is directly synthesized on a polymer substrate using a low‐temperature metal–organic chemical vapor deposition process, eliminating the need for additional patterning. The fabricated pressure sensor, with a sensitivity of ∼23 000 kPa −1 , benefits from the hierarchical multiscale structure, and the polymer cavity enables detection across a broad range of 0.135–80 kPa. Furthermore, by optimizing the synthesis conditions, we demonstrate that the sensitivity and detection range of the sensor are influenced by the material composition. These studies not only lay the foundation for the development of next‐generation wearable electronics but also are expected to broaden the application scope of 3D‐structured transition‐metal dichalcogenides in sensor technologies.
- 8 June 2026
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (59) , e31664
Open Access3D Hierarchical MoS 2 ‐Based Piezoresistive Pressure Sensors With Ultrahigh Sensitivity and Wide Dynamic Range
The rapid advancements in artificial intelligence, wearable devices, and the Internet of Things underscore the growing importance of sensor technology, particularly pressure sensors, for driving innovation across various fields. Wide‐dynamic‐range pressure sensors that exhibit high sensitivity without being biased toward a specific range are therefore needed. We propose an ultrahigh‐sensitivity, wide‐dynamic‐range pressure sensor that integrates 3D hierarchical (3DH) MoS 2 as the sensing material with a polymer cavity structure. 3DH MoS 2 is directly synthesized on a polymer substrate using a low‐temperature metal–organic chemical vapor deposition process, eliminating the need for additional patterning. The fabricated pressure sensor, with a sensitivity of ∼23 000 kPa −1 , benefits from the hierarchical multiscale structure, and the polymer cavity enables detection across a broad range of 0.135–80 kPa. Furthermore, by optimizing the synthesis conditions, we demonstrate that the sensitivity and detection range of the sensor are influenced by the material composition. These studies not only lay the foundation for the development of next‐generation wearable electronics but also are expected to broaden the application scope of 3D‐structured transition‐metal dichalcogenides in sensor technologies.
- Open Access
- 8 April 2026
- Published by The Korean Vacuum Society in Applied Science and Convergence Technology
- Vol. 35 (3) , 108-114
Real-Time Particle Measurement and Artificial Intelligence-Based Correlation Analysis of Wafer Defect in Semiconductor Plasma-Enhanced Chemical Vapor Deposition Process
Euna Jung, Jeongin Song, Byeonghyeon Min, Minsu Jeon, Jong Moon Ha, Sang Hyun Park, Taesung Kim, Sang-Woo Kang, Jae-Hyun Lee, and Jihun Mun. Applied Science and Convergence Technology 2026;35:108-14. https://doi.org/10.5757/ASCT.2026.35.3.108
- 8 April 2026
- Published by The Korean Vacuum Society in Applied Science and Convergence Technology
- Vol. 35 (3) , 108-114
Open AccessReal-Time Particle Measurement and Artificial Intelligence-Based Correlation Analysis of Wafer Defect in Semiconductor Plasma-Enhanced Chemical Vapor Deposition Process
Euna Jung, Jeongin Song, Byeonghyeon Min, Minsu Jeon, Jong Moon Ha, Sang Hyun Park, Taesung Kim, Sang-Woo Kang, Jae-Hyun Lee, and Jihun Mun. Applied Science and Convergence Technology 2026;35:108-14. https://doi.org/10.5757/ASCT.2026.35.3.108
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (3) , 667-674
A Study on Particle Emission Efficiency of a Plasma Enhanced Chemical Vapor Deposition Chamber During Periodic Cycle Purge Process Using an Improved Single Particle Light Scattering Method
In this study, the periodic purge process of the silicon nitride oxide deposition chamber was quantitatively analyzed and optimized using a real-time contaminant particle sensor (RTCPS). The RTCPS can measure the particle number concentration emitted from the semiconductor process chamber at the foreline in real time. The previous periodic purge process, which used a cycle purge method alternating between showerhead flow on and off, only expelled the accumulated particles in the chamber during the early stages of each cycle. On the other hand, by adding heater movement during the cycle, continuous particle emission was achieved throughout the periodic purge, resulting in improved efficiency. Additionally, the purge time was reduced, leading to increased productivity.
- 21 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (3) , 667-674
A Study on Particle Emission Efficiency of a Plasma Enhanced Chemical Vapor Deposition Chamber During Periodic Cycle Purge Process Using an Improved Single Particle Light Scattering Method
In this study, the periodic purge process of the silicon nitride oxide deposition chamber was quantitatively analyzed and optimized using a real-time contaminant particle sensor (RTCPS). The RTCPS can measure the particle number concentration emitted from the semiconductor process chamber at the foreline in real time. The previous periodic purge process, which used a cycle purge method alternating between showerhead flow on and off, only expelled the accumulated particles in the chamber during the early stages of each cycle. On the other hand, by adding heater movement during the cycle, continuous particle emission was achieved throughout the periodic purge, resulting in improved efficiency. Additionally, the purge time was reduced, leading to increased productivity.
- Open Access
- 30 November 2024
- Published by The Korean Vacuum Society in Applied Science and Convergence Technology
- Vol. 33 (6) , 176-180
Methodology for Evaluating Turbo Molecular Pump Pumping Performance via Pressure Gauge Correction and Anomaly Detection
- 30 November 2024
- Published by The Korean Vacuum Society in Applied Science and Convergence Technology
- Vol. 33 (6) , 176-180
Open AccessMethodology for Evaluating Turbo Molecular Pump Pumping Performance via Pressure Gauge Correction and Anomaly Detection
- Open Access
- 13 November 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (22) , 2937
Selective Laser-Assisted Direct Synthesis of MoS2 for Graphene/MoS2 Schottky Junction
Implementing a heterostructure by vertically stacking two-dimensional semiconductors is necessary for responding to various requirements in the future of semiconductor technology. However, the chemical-vapor deposition method, which is an existing two-dimensional (2D) material-processing method, inevitably causes heat damage to surrounding materials essential for functionality because of its high synthesis temperature. Therefore, the heterojunction of a 2D material that directly synthesized MoS2 on graphene using a laser-based photothermal reaction at room temperature was studied. The key to the photothermal-reaction mechanism is the difference in the photothermal absorption coefficients of the materials. The device in which graphene and MoS2 were vertically stacked using a laser-based photothermal reaction demonstrated its potential application as a photodetector that responds to light and its stability against cycling. The laser-based photothermal-reaction method for 2D materials will be further applied to various fields, such as transparent display electrodes, photodetectors, and solar cells, in the future.
- 13 November 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (22) , 2937
Open AccessSelective Laser-Assisted Direct Synthesis of MoS2 for Graphene/MoS2 Schottky Junction
Implementing a heterostructure by vertically stacking two-dimensional semiconductors is necessary for responding to various requirements in the future of semiconductor technology. However, the chemical-vapor deposition method, which is an existing two-dimensional (2D) material-processing method, inevitably causes heat damage to surrounding materials essential for functionality because of its high synthesis temperature. Therefore, the heterojunction of a 2D material that directly synthesized MoS2 on graphene using a laser-based photothermal reaction at room temperature was studied. The key to the photothermal-reaction mechanism is the difference in the photothermal absorption coefficients of the materials. The device in which graphene and MoS2 were vertically stacked using a laser-based photothermal reaction demonstrated its potential application as a photodetector that responds to light and its stability against cycling. The laser-based photothermal-reaction method for 2D materials will be further applied to various fields, such as transparent display electrodes, photodetectors, and solar cells, in the future.
- Open Access
- 31 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 573
Effect of Measurement System Configuration and Operating Conditions on 2D Material-Based Gas Sensor Sensitivity
Gas sensors applied in real-time detection of toxic gas leakage, air pollution, and respiration patterns require a reliable test platform to evaluate their characteristics, such as sensitivity and detection limits. However, securing reliable characteristics of a gas sensor is difficult, owing to the structural difference between the gas sensor measurement platform and the difference in measurement methods. This study investigates the effect of measurement conditions and system configurations on the sensitivity of two-dimensional (2D) material-based gas sensors. Herein, we developed a testbed to evaluate the response characteristics of MoS2-based gas sensors under a NO2 gas flow, which allows variations in their system configurations. Additionally, we demonstrated that the distance between the gas inlet and the sensor and gas inlet orientation influences the sensor performance. As the distance to the 2D gas sensor surface decreased from 4 to 2 mm, the sensitivity of the sensor improved to 9.20%. Furthermore, when the gas inlet orientation was perpendicular to the gas sensor surface, the sensitivity of the sensor was the maximum (4.29%). To attain the optimum operating conditions of the MoS2-based gas sensor, the effects of measurement conditions, such as gas concentration and temperature, on the sensitivity of the gas sensor were investigated.
- 31 January 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (3) , 573
Open AccessEffect of Measurement System Configuration and Operating Conditions on 2D Material-Based Gas Sensor Sensitivity
Gas sensors applied in real-time detection of toxic gas leakage, air pollution, and respiration patterns require a reliable test platform to evaluate their characteristics, such as sensitivity and detection limits. However, securing reliable characteristics of a gas sensor is difficult, owing to the structural difference between the gas sensor measurement platform and the difference in measurement methods. This study investigates the effect of measurement conditions and system configurations on the sensitivity of two-dimensional (2D) material-based gas sensors. Herein, we developed a testbed to evaluate the response characteristics of MoS2-based gas sensors under a NO2 gas flow, which allows variations in their system configurations. Additionally, we demonstrated that the distance between the gas inlet and the sensor and gas inlet orientation influences the sensor performance. As the distance to the 2D gas sensor surface decreased from 4 to 2 mm, the sensitivity of the sensor improved to 9.20%. Furthermore, when the gas inlet orientation was perpendicular to the gas sensor surface, the sensitivity of the sensor was the maximum (4.29%). To attain the optimum operating conditions of the MoS2-based gas sensor, the effects of measurement conditions, such as gas concentration and temperature, on the sensitivity of the gas sensor were investigated.
- Open Access
- 1 November 2020
- Published by AIP Publishing in AIP Advances
- Vol. 10 (11) , 115108
Development of a calibration system for wafer-type temperature sensor
Wafer-type temperature sensors are widely used during semiconductor fabrication as integrated monitoring sensors for the real-time monitoring of wafer surface temperature, which affects the quality and yield of semiconductor devices. In recent years, various wafer-type temperature sensors have been developed according to the process type and temperature range for monitoring the temperature distribution. However, there is little research on the calibration system to ensure the accuracy and reliability of the developed wafer-type temperature sensor. In this study, we designed a system for the calibration of wafer-type temperature sensors. With this system, the traceability of the sensor can be guaranteed by calibrating the sensing characteristics, such as area uniformity, temperature stability, and accuracy. The conventional temperature calibration bath is calibrated by placing a wafer-type temperature sensor in a liquid-controlled system to have uniform temperature. This method is difficult to apply to the field because the wafer-type temperature sensor can be contaminated by liquids and can adversely affect semiconductor processes. For this reason, we used a heating chamber similar to chemical vapor deposition equipment for a calibration system. We evaluated the properties of the calibration system including the rising time (which means the time taken to reach the target temperature) and temperature stability according to the heat capacity. Moreover, we developed a measurement method that allows for the evaluation of the temperature of the wafer-type temperature sensor within 15 min at 150 °C. The calibration system and measurement method developed in this study are expected to improve the efficiency of semiconductor fabrication processes.
- 1 November 2020
- Published by AIP Publishing in AIP Advances
- Vol. 10 (11) , 115108
Open AccessDevelopment of a calibration system for wafer-type temperature sensor
Wafer-type temperature sensors are widely used during semiconductor fabrication as integrated monitoring sensors for the real-time monitoring of wafer surface temperature, which affects the quality and yield of semiconductor devices. In recent years, various wafer-type temperature sensors have been developed according to the process type and temperature range for monitoring the temperature distribution. However, there is little research on the calibration system to ensure the accuracy and reliability of the developed wafer-type temperature sensor. In this study, we designed a system for the calibration of wafer-type temperature sensors. With this system, the traceability of the sensor can be guaranteed by calibrating the sensing characteristics, such as area uniformity, temperature stability, and accuracy. The conventional temperature calibration bath is calibrated by placing a wafer-type temperature sensor in a liquid-controlled system to have uniform temperature. This method is difficult to apply to the field because the wafer-type temperature sensor can be contaminated by liquids and can adversely affect semiconductor processes. For this reason, we used a heating chamber similar to chemical vapor deposition equipment for a calibration system. We evaluated the properties of the calibration system including the rising time (which means the time taken to reach the target temperature) and temperature stability according to the heat capacity. Moreover, we developed a measurement method that allows for the evaluation of the temperature of the wafer-type temperature sensor within 15 min at 150 °C. The calibration system and measurement method developed in this study are expected to improve the efficiency of semiconductor fabrication processes.