Romualdas Kliukas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Romualdas Kliukas has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ali Lakirouhani
Department of Civil Engineering, Faculty of Engineering, University of Zanjan, Zanjan 45371-38791, Iran
2 shared publications - Afshin Zohdi
Department of Geology, Faculty of Sciences 2 Zanjan
1 shared publication - Andrius Čeponis
Institute of Mechanical Science, Faculty of Mechanics, Vilnius Gediminas Technical University, Vilnius, Lithuania
1 shared publication - Daiva Makuteniene
Vilnius Gediminas Technical University
1 shared publication - Farhad Asemi
Department of Civil Engineering School of Engineering Kharazmi University Postal Code 15719–14911 Tehran Iran khu.ac.ir
1 shared publication - Hirotaka Suzuki
Kobe University
1 shared publication
Latest Publications
- 27 September 2024
- Published by Springer Nature
- p. 215-222
Integrating Graphical Methods into Engineering Education: Enhancing Learning and Visualization Skills in University Curricula
- 27 September 2024
- Published by Springer Nature
- p. 215-222
Integrating Graphical Methods into Engineering Education: Enhancing Learning and Visualization Skills in University Curricula
- Open Access
- 24 May 2021
- Published by Vilnius Gediminas Technical University in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
- Vol. 27 (5) , 346-354
COMPARISON OF PREDICTED FAILURE AREA AROUND THE BOREHOLES IN THE STRIKE-SLIP FAULTING STRESS REGIME WITH HOEK-BROWN AND FAIRHURST GENERALIZED CRITERIA
Breakout is a shear failure due to compression that forms around the borehole due to stress concentration. In this paper, the breakout theory model is investigated by combining the equilibrium elasticity equations of stress around the borehole with two Hoek-Brown and Fairhurst generalized fracture criteria, both of which are based on the Griffith criterion. This theory model provides an explicit equation for the breakout failure width, but the depth of failure is obtained by solving a quartic equation. According to the results and in general, in situ stresses and rock strength characteristics are effective in developing the breakout failure area, As the ratio of in-situ stresses increases, the breakout area becomes deeper and wider. Because in the shear zone, the failure envelope of the Fairhurst criterion is lower than the Hoek-Brown failure criterion, the Fairhurst criterion provides more depth for breakout than the Hoek-Brown criterion. However, due to the same compressive strength of the rock in these two criteria, the same failure width for breakout is obtained from these two criteria. Also, the results obtained for the depth of failure from the theoretical model based on the Fairhurst criterion are in good agreement with the laboratory results on Westerly granite.
- 24 May 2021
- Published by Vilnius Gediminas Technical University in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
- Vol. 27 (5) , 346-354
Open AccessCOMPARISON OF PREDICTED FAILURE AREA AROUND THE BOREHOLES IN THE STRIKE-SLIP FAULTING STRESS REGIME WITH HOEK-BROWN AND FAIRHURST GENERALIZED CRITERIA
Breakout is a shear failure due to compression that forms around the borehole due to stress concentration. In this paper, the breakout theory model is investigated by combining the equilibrium elasticity equations of stress around the borehole with two Hoek-Brown and Fairhurst generalized fracture criteria, both of which are based on the Griffith criterion. This theory model provides an explicit equation for the breakout failure width, but the depth of failure is obtained by solving a quartic equation. According to the results and in general, in situ stresses and rock strength characteristics are effective in developing the breakout failure area, As the ratio of in-situ stresses increases, the breakout area becomes deeper and wider. Because in the shear zone, the failure envelope of the Fairhurst criterion is lower than the Hoek-Brown failure criterion, the Fairhurst criterion provides more depth for breakout than the Hoek-Brown criterion. However, due to the same compressive strength of the rock in these two criteria, the same failure width for breakout is obtained from these two criteria. Also, the results obtained for the depth of failure from the theoretical model based on the Fairhurst criterion are in good agreement with the laboratory results on Westerly granite.
- Open Access
- 5 November 2020
- Published by Vilnius Gediminas Technical University in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
- Vol. 26 (8) , 789-799
PHYSICAL PARAMETERS, TENSILE AND COMPRESSIVE STRENGTH OF DOLOMITE ROCK SAMPLES: INFLUENCE OF GRAIN SIZE
The purpose of this paper is to investigate the strength, physical and engineering index parameters of selected dolomitic rocks with emphasis on grain size. For this purpose, three groups of dolomite from north western Iran, with the same mineral composition but different grain size, were selected; fine grain, medium grain and coarse grain. Three sets of laboratory experiments are performed on 32 samples: first; petrography tests for determining mineral composition and their percentage, and microstructure of rock containing grain size and grain size distribution, second; experiments to determine the physical properties of the rocks included density, compressional and shear wave velocity, and the third category of experiments included uniaxial compressive strength test, Brazilian tensile strength and point load strength. According to the results; there are significant positive correlation between grain size and uniaxial compressive strength (r = 0.89), point load strength (r = 0.58), Brazilian strength (r = 0.69), and average Young’s modulus (r = 0.64). Also, with increasing grain size, density decreases (r = –0.77). There is strong correlation between compressional wave velocity and shear velocity (r = 0.88). There are also a strong correlation among the uniaxial compressive strength, Brazilian tensile strength and point load strength.
- 5 November 2020
- Published by Vilnius Gediminas Technical University in JOURNAL OF CIVIL ENGINEERING AND MANAGEMENT
- Vol. 26 (8) , 789-799
Open AccessPHYSICAL PARAMETERS, TENSILE AND COMPRESSIVE STRENGTH OF DOLOMITE ROCK SAMPLES: INFLUENCE OF GRAIN SIZE
The purpose of this paper is to investigate the strength, physical and engineering index parameters of selected dolomitic rocks with emphasis on grain size. For this purpose, three groups of dolomite from north western Iran, with the same mineral composition but different grain size, were selected; fine grain, medium grain and coarse grain. Three sets of laboratory experiments are performed on 32 samples: first; petrography tests for determining mineral composition and their percentage, and microstructure of rock containing grain size and grain size distribution, second; experiments to determine the physical properties of the rocks included density, compressional and shear wave velocity, and the third category of experiments included uniaxial compressive strength test, Brazilian tensile strength and point load strength. According to the results; there are significant positive correlation between grain size and uniaxial compressive strength (r = 0.89), point load strength (r = 0.58), Brazilian strength (r = 0.69), and average Young’s modulus (r = 0.64). Also, with increasing grain size, density decreases (r = –0.77). There is strong correlation between compressional wave velocity and shear velocity (r = 0.88). There are also a strong correlation among the uniaxial compressive strength, Brazilian tensile strength and point load strength.