EHEmad Hosseinpour

Emad Hosseinpour

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Emad Hosseinpour has a total of 44 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development of a Stress Block Model to Predict the Ultimate Bending Capacity of Rectangular Concrete-Filled Steel Tube Beams Strengthened with U-Shaped CFRP Sheets

    by Mohammad Ansari, Ahmed W. Al Zand, Emad Hosseinpour, Ali Joharchi, Masoud Abedini

    The prediction of the ultimate bending capacity of the rectangular concrete-filled steel tube (RCFST) beams strengthened with U-shaped carbon fiber reinforced polymer (CFRP) sheets is limited to using the existing empirical models. Thus, this study aims to develop a new theoretical model based on a stress block model to predict the ultimate bending capacity (Mu) of the RCFST beams strengthened with a U-shaped CFRP-wrapping scheme. For this purpose, 28 finite element (FE) models of CFRP-strengthened RCFST beams had been analyzed for further investigation of the flexural behavior and longitudinal stresses distributed along with the beam’s components (steel tube, concrete core, and CFRP layers). The main parameters investigated are concrete compressive strength, steel yield strength, number of CFRP layers, and CFRP-wrapping-depth ratio. In addition, the Mu values obtained from the FE models of the current study and those from the existing experimental tests performed by others are used to verify the corresponding values that are theoretically predicted by the new model. The comparison showed that the proposed model is moderately conservative, as the predicted values of Mu are, on average, up to 10% lower than those obtained from experimental tests and FE analysis.


  • Open Access

    A multidisciplinary engineering-based approach for tunnelling strengthening with a new fibre reinforced shotcrete technology

    by Joaquim Barros, Hugo Costelha, David Bento, Nelson Brites, Rui Luís, Hugo Patrício, Vitor Cunha, Luís Bento, Tiago Miranda, Paulo Coelho, et al.


  • Open Access

    Innovation of Shear Connectors in Slim Floor Beam Construction

    by Mohamed S. Majdub, Shahrizan Baharom, Ahmed W. Al Zand, Azrul A. Mutalib, Emad Hosseinpour

    Composite slim floor systems are increasingly applied in the construction industry. Therefore, several experimental and numerical studies have been conducted to investigate the composite flooring systems and examine the various details that may affect the production of composite floors. This review paper summarises some important developments of composite slim floor beams, such as the type of steel beam cross section and shear connectors used, presenting essential results and important notes from various studies. The fundamental structural elements and the contribution of conducted studies towards improving the shear capacity of composite beams in enhancing the general structural behaviour were also described. Finally, the paper concludes with the potential of a deeper investigation of some issues that accompany the application of certain types of shear connects or steel shapes used to improve the composite slim floor system so that the improvement construction industry may make the most out of using composite construction techniques.


  • Open Access

    Flexural Strength of Internally Stiffened Tubular Steel Beam Filled with Recycled Concrete Materials

    by Ahmed W. Al Zand, Mustafa M. Ali, Riyadh Al-Ameri, Wan Hamidon Wan Badaruzzaman, Wadhah M. Tawfeeq, Emad Hosseinpour, Zaher Mundher Yaseen

    The flexural strength of Slender steel tube sections is known to achieve significant improvements upon being filled with concrete material; however, this section is more likely to fail due to buckling under compression stresses. This study investigates the flexural behavior of a Slender steel tube beam that was produced by connecting two pieces of C-sections and was filled with recycled-aggregate concrete materials (CFST beam). The C-section’s lips behaved as internal stiffeners for the CFST beam’s cross-section. A static flexural test was conducted on five large scale specimens, including one specimen that was tested without concrete material (hollow specimen). The ABAQUS software was also employed for the simulation and non-linear analysis of an additional 20 CFST models in order to further investigate the effects of varied parameters that were not tested experimentally. The numerical model was able to adequately verify the flexural behavior and failure mode of the corresponding tested specimen, with an overestimation of the flexural strength capacity of about 3.1%. Generally, the study confirmed the validity of using the tubular C-sections in the CFST beam concept, and their lips (internal stiffeners) led to significant improvements in the flexural strength, stiffness, and energy absorption index. Moreover, a new analytical method was developed to specifically predict the bending (flexural) strength capacity of the internally stiffened CFST beams with steel stiffeners, which was well-aligned with the results derived from the current investigation and with those obtained by others.


  • Open Access

    PUSHOVER ANALYSIS OF REINFORCED CONCRETE BUILDING WITH VERTICAL SHEAR LINK STEEL BRACES

    by Seyed Hamed Hosseini, Suhaimi Abu Bakar, Kamyar Bagherinejad, Emad Hosseinpour

    In recent decades, steel cross bracing has been used as a conventional method to retrofit concrete buildings. Most of the cases utilized concentric steel braces system. However, studies concerning the behavior of RC frames with eccentricity steel bracing are quite limited. In this research, three types of structures incorporating special moment frames, RC structure with invert V braces and RC structures with vertical link beams with different stories were modeled through SAP 2000 and analyzed by considering nonlinear static analysis (pushover). Results revealed that invert Y steel braces (vertical shear links) system is an alternative way to construct a ductile structure with great lateral stiffness. It was also found that the axial force in braces is controlled by the behavior of the vertical link beam.


  • An Overview of Component Condition Assessment Systems (CCAS)

    by N. Amani, E. Hosseinpour

    Recent requirements in component management of building systems have focused on the need for improving methods and metric tools to support component condition assessment and appropriate decisions for infrastructure owned facilities. A range of research articles (1975-2009) covering infrastructure system of component condition assessment systems (CCAS) is discussed to provide a practical and theoretical overview of CCAS infrastructure systems in industry and research. This paper reviews much of the literature on CCAS infrastructure systems. The literature is collected from major books, journals, technical reports and conference proceedings, the period covered is from 1975 to 2009. This paper finds that the focus of CCAS, surveyed in several aspects during the 35 years that have been investigated, from technology to measurement and from assessment function to component maintenance as an integrated part of the infrastructure component management. The purpose of this paper is to provide an overview of CCAS infrastructure system in industry and research. This paper offers help to researchers in understanding the selection of suitable method for component condition assessment in infrastructure systems.