Ana Álvarez-García
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ana Álvarez-García has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Javier Tarrío-Saavedra
Grupo MODES, CITIC, Departamento de Matemáticas Escuela Politécnica de Enxeñaría de Ferrol Universidade da Coruña Ferrol Spain
3 shared publications - Ana María Díaz-Díaz
Centro de Investigación en Tecnoloxías Navais e Industriais (CITENI), Campus Industrial de Ferrol, Universidade da Coruña, 15403 Ferrol, Spain
2 shared publications - Jorge López-Beceiro
Department of Naval and Industrial Engineering, Campus Industrial de Ferrol, Escola Politécnica de Enxeñaría de Ferrol, Universidade da Coruña, CITENI, PROTERM group, Ferrol, Spain
2 shared publications - Ramón Artiaga
University of A Coruña Avda. Mendizábal s/n
2 shared publications - Salvador Naya
Grupo MODES, CITIC, Departamento de Matemáticas Escuela Politécnica de Enxeñaría de Ferrol Universidade da Coruña Ferrol Spain
2 shared publications Ana Díaz-Díaz
CITENI-Grupo de Propiedades Térmicas y Reológicas de materiales, Departamento Matemáticas, Escola Politécnica de Enxeñaría de Ferrol, Universidade da Coruña, Ferrol, Spain
1 shared publication
Latest Publications
- Open Access
Characterization of Epoxy Adhesive for Marine Applications
The shipping industry faces the challenge of expanding its capabilities and mitigating its environmental impact. The utilization of adhesive bonding techniques has the potential to facilitate the construction of lighter ships with a reduced carbon footprint. In this work, a complete methodology has been established to study the properties of an adhesive bond between naval steel and the behavior of the bulk adhesive when introduced into seawater. Thermogravimetric analysis (TGA) has been used to determine the thermal properties. Single-lap-joint and tensile tests have been performed showing the negative influence of temperature on the mechanical properties. Seawater absorption has been studied by gravimetric tests. Differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and mechanical bulk tests have been carried out before and after aging. The water absorption is Fickian, and when a constant load is applied, the absorption occurs faster and in greater quantity, decreasing the stiffness and strength. An increase in the glass transition temperature was observed in the absence of a load, with no discernible change upon the application of load condition. Also, aged specimens with constant load exhibited a reduction in water content. These phenomena may be attributed to several diffusion processes.
Open AccessCharacterization of Epoxy Adhesive for Marine Applications
The shipping industry faces the challenge of expanding its capabilities and mitigating its environmental impact. The utilization of adhesive bonding techniques has the potential to facilitate the construction of lighter ships with a reduced carbon footprint. In this work, a complete methodology has been established to study the properties of an adhesive bond between naval steel and the behavior of the bulk adhesive when introduced into seawater. Thermogravimetric analysis (TGA) has been used to determine the thermal properties. Single-lap-joint and tensile tests have been performed showing the negative influence of temperature on the mechanical properties. Seawater absorption has been studied by gravimetric tests. Differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and mechanical bulk tests have been carried out before and after aging. The water absorption is Fickian, and when a constant load is applied, the absorption occurs faster and in greater quantity, decreasing the stiffness and strength. An increase in the glass transition temperature was observed in the absence of a load, with no discernible change upon the application of load condition. Also, aged specimens with constant load exhibited a reduction in water content. These phenomena may be attributed to several diffusion processes.
- 22 December 2023
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 28 (4) , 2531-2552
The effect of marine ageing on the mechanical properties of a structural adhesive
- 22 December 2023
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 28 (4) , 2531-2552
The effect of marine ageing on the mechanical properties of a structural adhesive
- Open Access
The Complexity of Lignin Thermal Degradation in the Isothermal Context
Thermal degradation of lignin in nitrogen atmosphere is evaluated by linear heating and isothermal tests. While linear heating suggests that thermal decomposition in the 200–400 °C range mainly consists of a single step, a careful analysis of isothermal tests points to different lignin fractions having different stabilities. This is an important point for practical predictions, since kinetics obtained as if the degradations at different temperatures were the same would lack practical utility. Instead, stairway type tests are proposed to evaluate the degradation rates and sample quantities involved at the temperatures of interest.
Open AccessThe Complexity of Lignin Thermal Degradation in the Isothermal Context
Thermal degradation of lignin in nitrogen atmosphere is evaluated by linear heating and isothermal tests. While linear heating suggests that thermal decomposition in the 200–400 °C range mainly consists of a single step, a careful analysis of isothermal tests points to different lignin fractions having different stabilities. This is an important point for practical predictions, since kinetics obtained as if the degradations at different temperatures were the same would lack practical utility. Instead, stairway type tests are proposed to evaluate the degradation rates and sample quantities involved at the temperatures of interest.
- Open Access
A Logistic Approach for Kinetics of Isothermal Pyrolysis of Cellulose
A kinetic model is proposed to fit isothermal thermogravimetric data obtained from cellulose in an inert atmosphere at different temperatures. The method used here to evaluate the model involves two steps: (1) fitting of single time-derivative thermogravimetric curves (DTG) obtained at different temperatures versus time, and (2) fitting of the rate parameter values obtained at different temperatures versus temperature. The first step makes use of derivative of logistic functions. For the second step, the dependence of the rate factor on temperature is evaluated. That separation of the curve fitting from the analysis of the rate factor resulted to be very flexible since it proved to work for previous crystallization studies and now for thermal degradation of cellulose.
Open AccessA Logistic Approach for Kinetics of Isothermal Pyrolysis of Cellulose
A kinetic model is proposed to fit isothermal thermogravimetric data obtained from cellulose in an inert atmosphere at different temperatures. The method used here to evaluate the model involves two steps: (1) fitting of single time-derivative thermogravimetric curves (DTG) obtained at different temperatures versus time, and (2) fitting of the rate parameter values obtained at different temperatures versus temperature. The first step makes use of derivative of logistic functions. For the second step, the dependence of the rate factor on temperature is evaluated. That separation of the curve fitting from the analysis of the rate factor resulted to be very flexible since it proved to work for previous crystallization studies and now for thermal degradation of cellulose.