Adam J. Morgan
Research Subjects
Research Interests
Adam J. Morgan has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Woongje Sung
College of Nanotechnology Science and Engineering, University at Albany, Albany, NY, USA
10 shared publications - Seung Yup Jang
College of Nanotechnology Science and Engineering, University at Albany, Albany, NY, USA
6 shared publications - Dongyoung Kim
College of Nanoscale Science and Engineering, State University of New York Polytechnic Institute, Albany, NY, USA
5 shared publications - Nick Yun
College of Nanoscale Science and Engineering, State University of New York Polytechnic Institute, Albany, NY, USA
4 shared publications - Skylar Deboer
College of Nanotechnology Science and Engineering, University at Albany, Albany, NY, USA
2 shared publications Aivars Lelis
U.S. Army Research Laboratory (ARL), Adelphi, MD 20783 USA
1 shared publication
Latest Publications
- Open Access
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 14, 204
Erratum to “Comprehensive Experimental and Simulation Study of Six 1.2kV SiC MOSFET Layout Topologies”
Presents corrections to the paper, (Comprehensive Experimental and Simulation Study of Six 1.2kV SiC MOSFET Layout Topologies).
- 17 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 14, 204
Open AccessErratum to “Comprehensive Experimental and Simulation Study of Six 1.2kV SiC MOSFET Layout Topologies”
Presents corrections to the paper, (Comprehensive Experimental and Simulation Study of Six 1.2kV SiC MOSFET Layout Topologies).
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (12) , 6906-6911
Static Electrothermal Study of >3 kV Co-Packaged MOSFETs and Monolithic BiDFETs
We report a comparison of the static electrothermal performance of SiC co-packaged MOSFETs and a monolithic bi-directional field effect transistor (BiDFET) fabricated in a commercial foundry from the same wafer. Both bi-directional switching solutions provide fully gate-controlled output characteristics in the first and third quadrants of operation, a specific on-resistance of ~50m $\Omega \cdot $ cm2 at room temperature, and a breakdown voltage that exceeds 3 kV. We demonstrate accurate extraction and monitoring of the junction temperature using variations in the on-resistance and validate this assertion through theoretical and experimental evidence. Our investigation reveals that the static electrical performance is identical and indicates the difference in thermal performance between the two bi-directional switching solutions is solely attributed to the arrangement of the chips within the package (i.e., an increased power density locally thermally saturates the package) instead of a fundamental property of the device architecture. To verify this, we present the results of an analytical heat flow model, which confirms that the increased rate of self-heating for the monolithically integrated BiDFET compared to two co-packaged MOSFETs is due to the increased heat flux density and limitation of the packaging thermals. This work demonstrates that the proximity of devices inherent to compact bi-directional SiC switches can lead to excessive device heating during extended states of conduction, emphasizing the need for advanced packaging.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (12) , 6906-6911
Static Electrothermal Study of >3 kV Co-Packaged MOSFETs and Monolithic BiDFETs
We report a comparison of the static electrothermal performance of SiC co-packaged MOSFETs and a monolithic bi-directional field effect transistor (BiDFET) fabricated in a commercial foundry from the same wafer. Both bi-directional switching solutions provide fully gate-controlled output characteristics in the first and third quadrants of operation, a specific on-resistance of ~50m $\Omega \cdot $ cm2 at room temperature, and a breakdown voltage that exceeds 3 kV. We demonstrate accurate extraction and monitoring of the junction temperature using variations in the on-resistance and validate this assertion through theoretical and experimental evidence. Our investigation reveals that the static electrical performance is identical and indicates the difference in thermal performance between the two bi-directional switching solutions is solely attributed to the arrangement of the chips within the package (i.e., an increased power density locally thermally saturates the package) instead of a fundamental property of the device architecture. To verify this, we present the results of an analytical heat flow model, which confirms that the increased rate of self-heating for the monolithically integrated BiDFET compared to two co-packaged MOSFETs is due to the increased heat flux density and limitation of the packaging thermals. This work demonstrates that the proximity of devices inherent to compact bi-directional SiC switches can lead to excessive device heating during extended states of conduction, emphasizing the need for advanced packaging.
- Open Access
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 1103-1111
Comprehensive Experimental and Simulation Study of Six 1.2 kV SiC MOSFET Layout Topologies
1.2 kV 4H-SiC MOSFETs with linear, hexagonal, square, and ladder topological layouts were designed with uniform design rules and fabricated simultaneously on the same wafer. These devices were then diced and packaged to conduct a comprehensive analysis between their static and dynamic electrical characteristics. 3D TCAD simulations for each device type were also conducted to further elucidate the trends observed with the experimental data. The ladder and hexagonal MOSFET designs both demonstrated the greatest improvement in specific on-resistance (Ron,sp) with no degradation in the breakdown voltage. However, 3D simulations of the blocking characteristics reveal that the maximum electric field in the oxide and 4H-SiC are greater in the hexagonal design due to the corner in the JFET region. Furthermore, the MOSFET with the ladder design demonstrates superior switching characteristics compared to the hexagonal design due to its large increase in channel density and minimal increase in JFET density, with a (FOMCiss/Crss) 2x greater than the Nominal MOSFET, where Ciss is the input capacitance and Cgd is the reverse transfer capacitance.
- 23 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 13, 1103-1111
Open AccessComprehensive Experimental and Simulation Study of Six 1.2 kV SiC MOSFET Layout Topologies
1.2 kV 4H-SiC MOSFETs with linear, hexagonal, square, and ladder topological layouts were designed with uniform design rules and fabricated simultaneously on the same wafer. These devices were then diced and packaged to conduct a comprehensive analysis between their static and dynamic electrical characteristics. 3D TCAD simulations for each device type were also conducted to further elucidate the trends observed with the experimental data. The ladder and hexagonal MOSFET designs both demonstrated the greatest improvement in specific on-resistance (Ron,sp) with no degradation in the breakdown voltage. However, 3D simulations of the blocking characteristics reveal that the maximum electric field in the oxide and 4H-SiC are greater in the hexagonal design due to the corner in the JFET region. Furthermore, the MOSFET with the ladder design demonstrates superior switching characteristics compared to the hexagonal design due to its large increase in channel density and minimal increase in JFET density, with a (FOMCiss/Crss) 2x greater than the Nominal MOSFET, where Ciss is the input capacitance and Cgd is the reverse transfer capacitance.
- 17 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7659-7665
Influence of P+ Body on Performance and Ruggedness of 1.2 kV 4H-SiC MOSFETs
This article reports an investigation into the impact of P $^{+}$ body design in 4H-silicon carbide (SiC) MOSFETs. Specifically, 1.2 kV SiC MOSFETs with various P $^{+}$ body designs were fabricated and analyzed. MOSFETs with stripe pattern P $^{+}$ body, orthogonal P $^{+}$ body, and without P $^{+}$ body were fabricated on the same wafer using the same mask set. A comprehensive comparison was conducted among the MOSFETs with different P $^{+}$ body designs, focusing on their static characteristics, switching characteristics, and avalanche ruggedness. Two-dimensional simulations were also performed to support experimental results. The orthogonal P $^{+}$ design was observed to provide improved conduction behaviors without adversely affecting the static characteristics, thanks to the reduced cell pitch. Conversely, MOSFETs without a P $^{+}$ body exhibited reduced breakdown voltage due to the inability to extract holes during avalanche conditions. The presence of a large area of P $^{+}$ body contact enhances the switching characteristics, whereas MOSFETs with a small area of P $^{+}$ body contact exhibit a slow change of potential within the p-well during switching. Additionally, similar results are observed in unclamped inductive switching (UIS). The small area of P $^{+}$ body contact causes a slow change of potential in the channel region during avalanche conditions. Consequently, the channel potential decreases, leading to higher avalanche current flow from the channel and a reduction in avalanche energy.
- 17 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7659-7665
Influence of P+ Body on Performance and Ruggedness of 1.2 kV 4H-SiC MOSFETs
This article reports an investigation into the impact of P $^{+}$ body design in 4H-silicon carbide (SiC) MOSFETs. Specifically, 1.2 kV SiC MOSFETs with various P $^{+}$ body designs were fabricated and analyzed. MOSFETs with stripe pattern P $^{+}$ body, orthogonal P $^{+}$ body, and without P $^{+}$ body were fabricated on the same wafer using the same mask set. A comprehensive comparison was conducted among the MOSFETs with different P $^{+}$ body designs, focusing on their static characteristics, switching characteristics, and avalanche ruggedness. Two-dimensional simulations were also performed to support experimental results. The orthogonal P $^{+}$ design was observed to provide improved conduction behaviors without adversely affecting the static characteristics, thanks to the reduced cell pitch. Conversely, MOSFETs without a P $^{+}$ body exhibited reduced breakdown voltage due to the inability to extract holes during avalanche conditions. The presence of a large area of P $^{+}$ body contact enhances the switching characteristics, whereas MOSFETs with a small area of P $^{+}$ body contact exhibit a slow change of potential within the p-well during switching. Additionally, similar results are observed in unclamped inductive switching (UIS). The small area of P $^{+}$ body contact causes a slow change of potential in the channel region during avalanche conditions. Consequently, the channel potential decreases, leading to higher avalanche current flow from the channel and a reduction in avalanche energy.
- Open Access
- 21 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 16659-16672
In Situ Detection of Bond Wire Lift-Off Events in Operational SiC MOSFETs
Bond wire lift-off is one of the main failure mechanisms for silicon carbide mosfet s. This occurs when the metallurgical weld between the bond-wire and the device source breaks creating an open circuit. The higher current on the remaining wires subjects them to additional thermal stress creating a positive feedback loop that can quickly lead to device failure if left unchecked. By detecting lift-off events during power converter operation damaged devices can be de-rated and equipment operators can be alerted to replace the power module before a failure occurs. This article presents an online, in situ monitoring circuit that can detect the incremental change in on-state inductance ( ${L_{\text{ds}}}$ ) caused by the redistribution of bond-wire current after a lift-off occurs. Unlike on-state resistance ( ${R_{\text{ds}}}$ ), the inductance does not depend on temperature, gate-oxide health, or gate-bias level. In addition, since the inductive impedance is frequency dependent, any bias related to converter operation can be suppressed by increasing the measurement frequency well above the switching frequency. Experimental results show that the proposed circuit can accurately measure inductive changes down to 10 pH, providing sufficient sensitivity to detect single wire lift-off events in test devices.
- 21 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (12) , 16659-16672
Open AccessIn Situ Detection of Bond Wire Lift-Off Events in Operational SiC MOSFETs
Bond wire lift-off is one of the main failure mechanisms for silicon carbide mosfet s. This occurs when the metallurgical weld between the bond-wire and the device source breaks creating an open circuit. The higher current on the remaining wires subjects them to additional thermal stress creating a positive feedback loop that can quickly lead to device failure if left unchecked. By detecting lift-off events during power converter operation damaged devices can be de-rated and equipment operators can be alerted to replace the power module before a failure occurs. This article presents an online, in situ monitoring circuit that can detect the incremental change in on-state inductance ( ${L_{\text{ds}}}$ ) caused by the redistribution of bond-wire current after a lift-off occurs. Unlike on-state resistance ( ${R_{\text{ds}}}$ ), the inductance does not depend on temperature, gate-oxide health, or gate-bias level. In addition, since the inductive impedance is frequency dependent, any bias related to converter operation can be suppressed by increasing the measurement frequency well above the switching frequency. Experimental results show that the proposed circuit can accurately measure inductive changes down to 10 pH, providing sufficient sensitivity to detect single wire lift-off events in test devices.
- 22 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (5) , 776-783
Package Design and Analysis of a 20-kV Double-Sided Silicon Carbide Diode Module With Polymer Nanocomposite Field-Grading Coating
To tackle the insulation challenges present in packaging medium-voltage silicon carbide power devices, we developed a package design for a 20-kV silicon carbide diode. This design incorporates a nonlinear resistive polymer-nanoparticle composite to boost insulation without compromising thermal performance. Employing a "sandwich" structure, where diodes are connected between direct-bonded copper substrates, our approach minimizes parasitic inductance (<4.5 nH) through a wire-bond-less design. According to thermal simulations, this configuration leads to a junction temperature reduction up to 53.5 oC. The submodule configuration not only cuts the total deformation by a factor of three but also enhances both reliability and manufacturability. By coating the electrode triple points with the resistive composite, electric field stress is diminished. Experimental tests indicated a 96% rise in the partial discharge inception voltage of substrates, increasing from 15.6 kV to 30.6 kV. For validation, scaled-down packages equipped with silicon carbide diodes exceeding 16 kV were fabricated and put through rigorous testing.
- 22 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 14 (5) , 776-783
Package Design and Analysis of a 20-kV Double-Sided Silicon Carbide Diode Module With Polymer Nanocomposite Field-Grading Coating
To tackle the insulation challenges present in packaging medium-voltage silicon carbide power devices, we developed a package design for a 20-kV silicon carbide diode. This design incorporates a nonlinear resistive polymer-nanoparticle composite to boost insulation without compromising thermal performance. Employing a "sandwich" structure, where diodes are connected between direct-bonded copper substrates, our approach minimizes parasitic inductance (<4.5 nH) through a wire-bond-less design. According to thermal simulations, this configuration leads to a junction temperature reduction up to 53.5 oC. The submodule configuration not only cuts the total deformation by a factor of three but also enhances both reliability and manufacturability. By coating the electrode triple points with the resistive composite, electric field stress is diminished. Experimental tests indicated a 96% rise in the partial discharge inception voltage of substrates, increasing from 15.6 kV to 30.6 kV. For validation, scaled-down packages equipped with silicon carbide diodes exceeding 16 kV were fabricated and put through rigorous testing.
- Open Access
- 2 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 989-995
The Effect of Deep JFET and P-Well Implant of 1.2kV 4H-SiC MOSFETs
1.2kV 4H-SiC MOSFETs with different junction depths of JFET and P-well regions were fabricated. For each JFET/P-well depth combination, channel lengths and JFET widths were also varied to compare specific on-resistance, breakdown voltage, and short-circuit withstand time. It was discovered that deep JFET structure provides low specific on-resistance (12% lower) with high breakdown voltage. On the other hand, MOSFETs with deep P-well result in high breakdown voltage with low leakage current even in shorter channel length (0.4 lm). Moreover, trade-off relationship between Ron,sp and short-circuit withstand time is discussed for MOSFETs with different JFET widths and channel lengths; the deep JFET implant provides better trade-off relationship due to the feasibility of narrow JFET width. For the further improvement of trade-off relationship, MOSFETs with deep JFET and P-well implant are proposed. Lastly, the importance of high channel mobility for not only static characteristics but also short-circuit characteristics was investigated. The in-depth understanding of measured electrical characteristics was supported by 2D-device simulations.
- 2 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 989-995
Open AccessThe Effect of Deep JFET and P-Well Implant of 1.2kV 4H-SiC MOSFETs
1.2kV 4H-SiC MOSFETs with different junction depths of JFET and P-well regions were fabricated. For each JFET/P-well depth combination, channel lengths and JFET widths were also varied to compare specific on-resistance, breakdown voltage, and short-circuit withstand time. It was discovered that deep JFET structure provides low specific on-resistance (12% lower) with high breakdown voltage. On the other hand, MOSFETs with deep P-well result in high breakdown voltage with low leakage current even in shorter channel length (0.4 lm). Moreover, trade-off relationship between Ron,sp and short-circuit withstand time is discussed for MOSFETs with different JFET widths and channel lengths; the deep JFET implant provides better trade-off relationship due to the feasibility of narrow JFET width. For the further improvement of trade-off relationship, MOSFETs with deep JFET and P-well implant are proposed. Lastly, the importance of high channel mobility for not only static characteristics but also short-circuit characteristics was investigated. The in-depth understanding of measured electrical characteristics was supported by 2D-device simulations.
- Open Access
- 22 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 495-503
Channel Design Optimization for 1.2-kV 4H-SiC MOSFET Achieving Inherent Unipolar Diode 3rd Quadrant Operation
SiC Schottky Barrier Diodes (SBDs) have been used in parallel with SiC MOSFETs as a freewheeling diode in power converter applications because the inherent PN body diode of the MOSFET has relatively high forward voltage drop, considerable reverse recovery current, and suffers from the expansion of stacking faults over the lifetime of the device [1] . However, an additional external diode requires extra space within a multi-chip package or power module, and adds undesirable parasitic inductance to the power loop during commutation events of the power converter. Alternatively, when the unipolar diode structure is integrated within the MOSFET, a significant reduction in wafer area is achieved by sharing active and edge termination areas. Monolithic integration of Schottky or JBS diode in a SiC MOSFET structure (JBSFET) and SiC MOSFET integrating the unipolar internal inverse channel diode were reported earlier [2] – [5] , respectively. However, JBSFET from [2] has higher specific on-resistance due to the larger cell pitch from the portion of JBS diode when compared with standalone MOSFET. For [5] , the fabrication of the proposed MOSFET requires a very thin and heavily doped epitaxial regrowth process, which may result in a complicated process.
- 22 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 495-503
Open AccessChannel Design Optimization for 1.2-kV 4H-SiC MOSFET Achieving Inherent Unipolar Diode 3rd Quadrant Operation
SiC Schottky Barrier Diodes (SBDs) have been used in parallel with SiC MOSFETs as a freewheeling diode in power converter applications because the inherent PN body diode of the MOSFET has relatively high forward voltage drop, considerable reverse recovery current, and suffers from the expansion of stacking faults over the lifetime of the device [1] . However, an additional external diode requires extra space within a multi-chip package or power module, and adds undesirable parasitic inductance to the power loop during commutation events of the power converter. Alternatively, when the unipolar diode structure is integrated within the MOSFET, a significant reduction in wafer area is achieved by sharing active and edge termination areas. Monolithic integration of Schottky or JBS diode in a SiC MOSFET structure (JBSFET) and SiC MOSFET integrating the unipolar internal inverse channel diode were reported earlier [2] – [5] , respectively. However, JBSFET from [2] has higher specific on-resistance due to the larger cell pitch from the portion of JBS diode when compared with standalone MOSFET. For [5] , the fabrication of the proposed MOSFET requires a very thin and heavily doped epitaxial regrowth process, which may result in a complicated process.
- 24 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (5) , 785-788
An Optimal Design for 1.2kV 4H-SiC JBSFET (Junction Barrier Schottky Diode Integrated MOSFET) With Deep P-Well
This letter reports the demonstration of 1.2 kV 4H-SiC Schottky-integrated MOSFETs (JBSFETs) achieving the same specific on-resistance as the pure MOSFET by using an innovative layout approach as well as novel deep P-well structure. The proposed JBSFET significantly reduces the specific on-resistance accomplishing 2x reduction in the chip size, when compared with the traditional, chip-to-chip parallel connection of separate MOSFET and JBS diode. Moreover, the leakage current originated from the Schottky contact was successfully suppressed by adopting a $1.8~\mu \text{m}$ deep P-well structure implemented by channeling implantation. Device design strategy with layout approach, fabrication, and static and short-circuit characteristics are discussed in this letter. In order to understand and clarify the experimental results, 2D simulations were conducted.
- 24 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (5) , 785-788
An Optimal Design for 1.2kV 4H-SiC JBSFET (Junction Barrier Schottky Diode Integrated MOSFET) With Deep P-Well
This letter reports the demonstration of 1.2 kV 4H-SiC Schottky-integrated MOSFETs (JBSFETs) achieving the same specific on-resistance as the pure MOSFET by using an innovative layout approach as well as novel deep P-well structure. The proposed JBSFET significantly reduces the specific on-resistance accomplishing 2x reduction in the chip size, when compared with the traditional, chip-to-chip parallel connection of separate MOSFET and JBS diode. Moreover, the leakage current originated from the Schottky contact was successfully suppressed by adopting a $1.8~\mu \text{m}$ deep P-well structure implemented by channeling implantation. Device design strategy with layout approach, fabrication, and static and short-circuit characteristics are discussed in this letter. In order to understand and clarify the experimental results, 2D simulations were conducted.
- Open Access
- 2 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 804-812
An Inclusive Structural Analysis on the Design of 1.2kV 4H-SiC Planar MOSFETs
A detailed structural analysis of 1.2 kV 4H-SiC MOSFETs with accumulation mode channel is reported in this paper. 1.2 kV SiC MOSFETs with a variety of cell designs were fabricated and compared with respect to the output and transfer characteristics, and blocking behaviors. All the design rules, such as channel length, JFET width, contact openings, gate-to-source overlap, and cell pitch were investigated to clearly provide the quantitative impact on the static performances. 2D-simulation was also conducted to support experimental results. As a result, it turned out that the channel length is the most determining factor for the specific on-resistance, resulting in 0.364$\text{m}\Omega $ -cm 2 increase per$0.1~ {\mu }\text{m}$ increase in the channel length. However, the channel potential is also largely dependent on the channel length such that the leakage current tends to increase with short channel design. The enhanced doping in the JFET region with a current spreading layer (CSL) is essential for achieving a narrower JFET width, which satisfies all static performances, as well as device reliability and ruggedness. Methods to further improve the trade-off characteristics using other design aspects are discussed in this paper.- 2 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 804-812
Open AccessAn Inclusive Structural Analysis on the Design of 1.2kV 4H-SiC Planar MOSFETs
A detailed structural analysis of 1.2 kV 4H-SiC MOSFETs with accumulation mode channel is reported in this paper. 1.2 kV SiC MOSFETs with a variety of cell designs were fabricated and compared with respect to the output and transfer characteristics, and blocking behaviors. All the design rules, such as channel length, JFET width, contact openings, gate-to-source overlap, and cell pitch were investigated to clearly provide the quantitative impact on the static performances. 2D-simulation was also conducted to support experimental results. As a result, it turned out that the channel length is the most determining factor for the specific on-resistance, resulting in 0.364$\text{m}\Omega $ -cm 2 increase per$0.1~ {\mu }\text{m}$ increase in the channel length. However, the channel potential is also largely dependent on the channel length such that the leakage current tends to increase with short channel design. The enhanced doping in the JFET region with a current spreading layer (CSL) is essential for achieving a narrower JFET width, which satisfies all static performances, as well as device reliability and ruggedness. Methods to further improve the trade-off characteristics using other design aspects are discussed in this paper.