Werner Klaus
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Werner Klaus has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- Jun Sakaguchi
Photonic Network Laboratory, National Institute of Information and Communications Technology, Tokyo, Japan
9 shared publications - Jose Manuel Delgado Mendinueta
Photonic Network System Laboratory, National Institute of Information and Communication Technology (NICT), Tokyo, Japan
7 shared publications - Naoya Wada
National Institute of Information and Communications Technology, Tokyo, Japan
6 shared publications - Yoshinari Awaji
New generation network research center, National Institute of Information and Communications Technology, Tokyo, NA Japan 184-8795
6 shared publications Yoshinari Awaji
Photonic Network System Laboratory, National Institute of Information and Communication Technology (NICT), 4-2-1 Nukui-Kitamachi, Koganei, Tokyo 184-8795, Japan
5 shared publicationsBenjamin J. Puttnam
National Institute of Information and Communications Technology
4 shared publications
Latest Publications
- 1 January 2025
- Published by Optica Publishing Group
- p. FTu1E.2
Multicore vs. Hollow-Core Fibers: Capacity and Scalability in Ultra-Long-Haul Submarine Transmission Scenarios
We compare power-constrained submarine cable capacities of SMF, HCF, and MCF systems highlighting the capacity advantage of MCF. We also investigate the impact of spatial channels, attenuation, and power supply on ultra-long-haul transmission performance.
- 1 January 2025
- Published by Optica Publishing Group
- p. FTu1E.2
Multicore vs. Hollow-Core Fibers: Capacity and Scalability in Ultra-Long-Haul Submarine Transmission Scenarios
We compare power-constrained submarine cable capacities of SMF, HCF, and MCF systems highlighting the capacity advantage of MCF. We also investigate the impact of spatial channels, attenuation, and power supply on ultra-long-haul transmission performance.
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Crosstalk suppression by mid-span isolators in bidirectional multi-core fiber transmission systems
Isolators are common optical elements used in optical amplifiers. We investigate the effect of additional mid-span isolators on the various types of inter-core crosstalk in bidirectional MCF transmission systems and show how mid-span isolators can be used to mitigate crosstalk.
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Crosstalk suppression by mid-span isolators in bidirectional multi-core fiber transmission systems
Isolators are common optical elements used in optical amplifiers. We investigate the effect of additional mid-span isolators on the various types of inter-core crosstalk in bidirectional MCF transmission systems and show how mid-span isolators can be used to mitigate crosstalk.
- Top Cited PapersOpen Access
- 10 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Proceedings of the IEEE
- Vol. 110 (11) , 1619-1654
The Role of Parallelism in the Evolution of Optical Fiber Communication Systems
In order to overcome the capacity limitations of current lightwave systems based on the single-mode optical fiber, massively parallel transmission in the spatial domain [space-division multiplexing (SDM)] supported by extended parallelism in the frequency domain (ultrawideband (UWB) systems) must be used. This article reviews key aspects of parallel transmission systems as the only significant capacity scaling option going forward and discusses the various tradeoffs on an architectural level and a hardware integration level. In doing so, this article also serves as an introduction to the more detailed accounts of fiber-optic systems and their future scaling within this Special Issue of the Proceedings of the IEEE.
- 10 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Proceedings of the IEEE
- Vol. 110 (11) , 1619-1654
Top Cited PapersOpen AccessThe Role of Parallelism in the Evolution of Optical Fiber Communication Systems
In order to overcome the capacity limitations of current lightwave systems based on the single-mode optical fiber, massively parallel transmission in the spatial domain [space-division multiplexing (SDM)] supported by extended parallelism in the frequency domain (ultrawideband (UWB) systems) must be used. This article reviews key aspects of parallel transmission systems as the only significant capacity scaling option going forward and discusses the various tradeoffs on an architectural level and a hardware integration level. In doing so, this article also serves as an introduction to the more detailed accounts of fiber-optic systems and their future scaling within this Special Issue of the Proceedings of the IEEE.
- 1 January 2022
- Published by Optica Publishing Group
- p. M2C.4
Hollow-core fiber capacities with receiver noise limitations
Hollow-core fiber promises low loss and low nonlinearity over wide operational bandwidths. However, considering realistic transponder noise floors reveals much lower capacity gains over standard single-mode fiber than generally assumed, even for optimistic fiber designs.
- 1 January 2022
- Published by Optica Publishing Group
- p. M2C.4
Hollow-core fiber capacities with receiver noise limitations
Hollow-core fiber promises low loss and low nonlinearity over wide operational bandwidths. However, considering realistic transponder noise floors reveals much lower capacity gains over standard single-mode fiber than generally assumed, even for optimistic fiber designs.
- 29 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (22) , 1427-1430
Impulse Response Measurement of Spooled and Twisted Few-Mode Multi-Core Fiber for Short-Range Optical Links
The impact of bending and twisting on the impulse response matrix is investigated using optical vector network analysis. The heterogeneous 36-core 3-mode fiber under test is spooled at bending radii of 8 cm to 50 cm and additionally up to 4 twists per meter along the longitudinal direction are applied. The by-design large differential mode group delay of the fiber enables comprehensive measurement of the inter-mode-group cross-talk of the fiber impulse response matrix, which is directly measured with an optical vector network analyzer. A maximal inter-mode-group cross-talk of -28.1 dB is observed over all 36 cores. Furthermore, no significant changes related to the bending radii or additional strain by twisting the fiber were detected. These results demonstrate that the transmission characteristics of few-mode fibers with large differential mode group delay are fairly unaffected by bend- and twist-related perturbations which may prove beneficial for short-range mode-group multiplexed transmission systems using partial multiple-input multiple-output equalization in conjunction with mode-selective multiplexers.
- 29 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (22) , 1427-1430
Impulse Response Measurement of Spooled and Twisted Few-Mode Multi-Core Fiber for Short-Range Optical Links
The impact of bending and twisting on the impulse response matrix is investigated using optical vector network analysis. The heterogeneous 36-core 3-mode fiber under test is spooled at bending radii of 8 cm to 50 cm and additionally up to 4 twists per meter along the longitudinal direction are applied. The by-design large differential mode group delay of the fiber enables comprehensive measurement of the inter-mode-group cross-talk of the fiber impulse response matrix, which is directly measured with an optical vector network analyzer. A maximal inter-mode-group cross-talk of -28.1 dB is observed over all 36 cores. Furthermore, no significant changes related to the bending radii or additional strain by twisting the fiber were detected. These results demonstrate that the transmission characteristics of few-mode fibers with large differential mode group delay are fairly unaffected by bend- and twist-related perturbations which may prove beneficial for short-range mode-group multiplexed transmission systems using partial multiple-input multiple-output equalization in conjunction with mode-selective multiplexers.
- 20 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (4) , 1048-1055
Highly Spectral Efficient C + L-Band Transmission Over a 38-Core-3-Mode Fiber
High capacity transmission with a data rate over 10.66 Pb/s is demonstrated in a 13 km, 38-core-3-mode few-mode multi-core fiber. This was achieved with a single optical comb source to generate 368 x 24.5 GBaud 64- or 256-quadrature-amplitude-modulated signals in a 25 GHz wavelength channel spacing in combination with a few-mode multi-core fiber with high uniformity amongst cores. We investigated the essential transmission channel characteristics and found that mode-dependent loss strongly decreases the achievable data-rates in some cores, while we did not find a correlation between increased impulse response spread and data-rate. We further have found no influence of the (radial) position of a core within the cladding on the data-rate. We further explored the potential of multi-span transmission over the same fiber with transmission distances up to 65 km, showing a strong performance penalty from prototype components with sub-optimal transmission properties.
- 20 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (4) , 1048-1055
Highly Spectral Efficient C + L-Band Transmission Over a 38-Core-3-Mode Fiber
High capacity transmission with a data rate over 10.66 Pb/s is demonstrated in a 13 km, 38-core-3-mode few-mode multi-core fiber. This was achieved with a single optical comb source to generate 368 x 24.5 GBaud 64- or 256-quadrature-amplitude-modulated signals in a 25 GHz wavelength channel spacing in combination with a few-mode multi-core fiber with high uniformity amongst cores. We investigated the essential transmission channel characteristics and found that mode-dependent loss strongly decreases the achievable data-rates in some cores, while we did not find a correlation between increased impulse response spread and data-rate. We further have found no influence of the (radial) position of a core within the cladding on the data-rate. We further explored the potential of multi-span transmission over the same fiber with transmission distances up to 65 km, showing a strong performance penalty from prototype components with sub-optimal transmission properties.
- 14 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (1) , 123-130
High Data-Rate and Long Distance MCF Transmission With 19-Core C+L band Cladding-Pumped EDFA
We describe a series of optical transmission experiments based around single-mode multi-core fiber (MCF) amplified with 19-core, C + L band Erbium-doped fiber amplifier (EDFA). The cladding-pumped amplifier uses two fan-cooled multi-mode pumps in each of C and L band to provide gain bandwidth over more than 75 nm. For recirculating transmission of PDM-16QAM signals on 345 wavelength carriers between 1530.52 nm and 1605.52 nm, we measure 0.715 Pb/s transmission over a distance of 2009 km (64 recirculations), equivalent to a throughput-distance product of 1.44 exabit/s x km. Next, using PDM-QPSK modulation, we investigate trans-oceanic transmission distances, measuring throughputs of 18.6 Tb/s and 14.5 Tb/s in 2 cores after 255 recirculations, a distance of 8007 km. Further, we evaluate the combined EDFA and fiber crosstalk penalties showing a core and wavelength dependence in agreement with previous MCF crosstalk measurements. These results demonstrate the potential of high core-count EDFAs to combine both high capacity transmission over transoceanic distances with benefits of SDM integration.
- 14 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (1) , 123-130
High Data-Rate and Long Distance MCF Transmission With 19-Core C+L band Cladding-Pumped EDFA
We describe a series of optical transmission experiments based around single-mode multi-core fiber (MCF) amplified with 19-core, C + L band Erbium-doped fiber amplifier (EDFA). The cladding-pumped amplifier uses two fan-cooled multi-mode pumps in each of C and L band to provide gain bandwidth over more than 75 nm. For recirculating transmission of PDM-16QAM signals on 345 wavelength carriers between 1530.52 nm and 1605.52 nm, we measure 0.715 Pb/s transmission over a distance of 2009 km (64 recirculations), equivalent to a throughput-distance product of 1.44 exabit/s x km. Next, using PDM-QPSK modulation, we investigate trans-oceanic transmission distances, measuring throughputs of 18.6 Tb/s and 14.5 Tb/s in 2 cores after 255 recirculations, a distance of 8007 km. Further, we evaluate the combined EDFA and fiber crosstalk penalties showing a core and wavelength dependence in agreement with previous MCF crosstalk measurements. These results demonstrate the potential of high core-count EDFAs to combine both high capacity transmission over transoceanic distances with benefits of SDM integration.
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (16) , 4001-4007
Enhanced Modal Dispersion Estimation Enabled by Chromatic Dispersion Compensation in Optical Vector Network Analysis
Component characterization is fundamental for understanding the limits of optical devices, sub-systems and transmission systems. With the introduction of space division multiplexing in optical fiber transmission systems, new impairments such as mode dependent loss and differential mode dispersion arise. Spatially-diverse optical vector network analyzers are capable of measuring these characteristics in a fast single sweep over a very large bandwidth. As a result of this large bandwidth, these analyzers are sensitive to differential chromatic dispersion within the interferometric measurement setup. This work discusses the influence and compensation of differential chromatic dispersion in such systems. Partial chromatic dispersion compensation is demonstrated to improve the representation and accuracy of impulse response measurements obtained from optical vector network analyzers for fibers and components with large differential chromatic dispersion. Analysis of a 39 core few-mode multi-core fiber is discussed, reporting variances of -2.9 ps/nm to -0.1 ps/nm, and 0.6 ps/nm to 6.9 ps/nm for the two mode groups, respectively, between the few-mode cores. A correlation with the total impulse response is observed. Furthermore, a maximum propagation skew of 20 ns between cores is observed after 13.6 km.
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (16) , 4001-4007
Enhanced Modal Dispersion Estimation Enabled by Chromatic Dispersion Compensation in Optical Vector Network Analysis
Component characterization is fundamental for understanding the limits of optical devices, sub-systems and transmission systems. With the introduction of space division multiplexing in optical fiber transmission systems, new impairments such as mode dependent loss and differential mode dispersion arise. Spatially-diverse optical vector network analyzers are capable of measuring these characteristics in a fast single sweep over a very large bandwidth. As a result of this large bandwidth, these analyzers are sensitive to differential chromatic dispersion within the interferometric measurement setup. This work discusses the influence and compensation of differential chromatic dispersion in such systems. Partial chromatic dispersion compensation is demonstrated to improve the representation and accuracy of impulse response measurements obtained from optical vector network analyzers for fibers and components with large differential chromatic dispersion. Analysis of a 39 core few-mode multi-core fiber is discussed, reporting variances of -2.9 ps/nm to -0.1 ps/nm, and 0.6 ps/nm to 6.9 ps/nm for the two mode groups, respectively, between the few-mode cores. A correlation with the total impulse response is observed. Furthermore, a maximum propagation skew of 20 ns between cores is observed after 13.6 km.
- 24 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (8) , 1756-1763
228-Spatial-Channel Bi-Directional Data Communication System Enabled by 39-Core 3-Mode Fiber
We demonstrated simultaneous usage of 228 spatial channels (effectively) within a strand of fiber. We fabricated a 13- km 39-core 3-mode fiber and constructed a bi-directional SDM transmission setup by using cascaded spatial multiplexers on both fiber ends. Aggregated inter-core crosstalk and return loss of the system were below -35 dB and above 31 dB, respectively, over the C and L bands. The feasibility of using bi-directional SDM transmission was investigated using 10 GBaud, 37.38-Gb/s dualpolarization QPSK signals at 1550 nm and coherent detection with a 6 × 6 MIMO equalizer. Excellent transmission properties were obtained for most spatial channels.
- 24 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 37 (8) , 1756-1763
228-Spatial-Channel Bi-Directional Data Communication System Enabled by 39-Core 3-Mode Fiber
We demonstrated simultaneous usage of 228 spatial channels (effectively) within a strand of fiber. We fabricated a 13- km 39-core 3-mode fiber and constructed a bi-directional SDM transmission setup by using cascaded spatial multiplexers on both fiber ends. Aggregated inter-core crosstalk and return loss of the system were below -35 dB and above 31 dB, respectively, over the C and L bands. The feasibility of using bi-directional SDM transmission was investigated using 10 GBaud, 37.38-Gb/s dualpolarization QPSK signals at 1550 nm and coherent detection with a 6 × 6 MIMO equalizer. Excellent transmission properties were obtained for most spatial channels.