Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yuxiang Zhang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Damage Identification of Chemical Milling Stiffened Panel Based on Lamb Wave and Inception-Convolutional Neural Network

    by Xie Jiang, Xize Chen, Wensong Zhou, Xiaojun Jiang, Jiefeng Xie, Xin Zhang, Yuxiang Zhang, Zhengwei Yang

    Mode conversion and wave scattering will occur when ultrasonic guided wave (GW) propagates to the stiffener which makes the received signals complex and poorly interpretable, thus limiting the application of GW in damage detection of chemical milling stiffened panel (CMSP). This article proposes a deep learning (DL) model inception-convolutional neural network (Inception-CNN) to realize damage localization of CMSP. First, a model analysis was conducted to get the resonant frequency of the piezoelectric wafer, and the mode conversion at the stiffener was explored through numerical analysis. Then, the identification effect based on the conventional damage imaging method was discussed. Finally, for training the proposed DL model, the residual signals were collected as a dataset after setting damages in different zones of CMSP. The model was then trained and tested, and its performance was analyzed and demonstrated. The results indicate that S0 mode has a greater conversion degree than A0 mode at the stiffener; GWs do not propagate in the form of a uniform wavefront on CMSP and conventional damage imaging methods based on the wave propagation paths are not applicable to CMSP. The model proposed can automatically extract the signal spatial features, accurately identify the corresponding damage zone, and its accuracy reaches 94% in the testing set. As the input features increase, the classification ability of the model will be further improved. The noise interference experiment shows that the model has good noise resistance performance at noise levels below 15%, indicating the feasibility of the model for practical applications.


  • Open Access

    An Electromechanical Impedance‐Based Imaging Algorithm for Damage Identification of Chemical Milling Stiffened Panel

    by Xie Jiang, Wensong Zhou, Xize Chen, Xin Zhang, Jiefeng Xie, Tao Tang, Yuxiang Zhang, Zhengwei Yang

    The multiple intersecting stiffeners on the chemical milling stiffened panel (CMSP) limit the application of active health monitoring methods on it. An imaging algorithm based on electromechanical impedance (EMI) and probability‐weighting is proposed to achieve quantitative evaluation and localization of the damage on CMSP. The proposed algorithm compensates for the difference in sensor performance with coefficients and there is no need to determine the key parameters of the algorithm through prior experiments. In the paper, the applicability of ultrasonic guided wave (GW) and EMI on CMSP was first studied through the finite element method. Based on EMI and the mean absolute percentage deviation (MAPD), the selected damage indicator (DI), a probability‐weighted damage imaging algorithm are proposed and experimentally verified. The results indicate that due to the reflection and attenuation effects of stiffeners on GW, the signal characteristics of damage scattering waves are contaminated, making it difficult to quantitatively characterize the damage from GW signals through DIs. MAPD is positively correlated with the damage degree and has consistency in characterizing the signal of different PZTs under the same working condition. The feasibility and accuracy of the proposed algorithm are verified through experiments which show a strong engineering application capability.


  • Open Access

    Electrical admittance-based evaluation of piezoelectric active sensor condition using k-nearest neighbors and least-squares regression

    by Xie Jiang, Xin Zhang, Yuxiang Zhang

    In the electromechanical impedance-based health monitoring of structures, partial failure of piezoelectric lead zirconate titanate will result in signal changes, which may cause misjudgment of the structure state. Therefore, this paper proposes an evaluation method of the sensor condition based on k-nearest neighbors (kNNs) and least-squares regression (LSR) to make monitoring more reliable. After the analysis of the signal characteristics of three structural changes and four sensor faults, the principal components (PCs) of three indices are extracted by principal component analysis. Next, the kNN classifier is trained with the data represented by PCs and then tested by tenfold cross-validation. To determine the degree of sensor faults, LSR is used to fit the damage degree laws with multivariate nonlinear equations. The results show that the kNN model trained with three PCs has higher classification accuracy than the one trained with two PCs. The accuracy of the former reaches 100%. The R2 values of damage degree regressions of four sensor faults are all greater than 0.85, and the p-values are far less than 0.05, which denotes the effectiveness of the regression in the prediction of damage degree. This method has great application potential in evaluating sensor conditions accurately and quickly.


  • Open Access

    Electromechanical impedance based self-diagnosis of piezoelectric smart structure using principal component analysis and LibSVM

    by Xie Jiang, Xin Zhang, Tao Tang, Yuxiang Zhang

    The long-term use of a piezoelectric smart structure make it difficult to judge whether the structure or piezoelectric lead zirconate titanate (PZT) is damaged when the signal changes. If the sensor fault occurs, the cases and degrees of the fault are unknown based on the electromechanical impedance method. Therefore, after the principal component analysis (PCA) of six characteristic indexes, a two-component solution that could explain 99.2% of the variance in the original indexes was obtained to judge whether the damage comes from the PZT. Then LibSVM was used to make an effective identification of four sensor faults (pseudo soldering, debonding, wear, and breakage) and their three damage degrees. The result shows that the identification accuracy of damaged PZT reached 97.5%. The absolute scores of PCA comprehensive evaluation for structural damages are less than 0.5 while for sensor faults are greater than 0.6. By comparing the scores of the samples under unknown conditions with the set threshold, whether the sensor faults occur is effectively judged; the intact and 12 possible damage states of PZT can be all classified correctly with the model trained by LibSVM. It is feasible to use LibSVM to classify the cases and degrees of sensor faults.


  • Open Access

    Electromechanical Impedance Based Self-Diagnosis of Piezoelectric Smart Structure Using Principal Component Analysis and LibSVM

    by Xie Jiang, Xin Zhang, Tao Tang, Yuxiang Zhang

    The long-term use of a piezoelectric smart structure make it difficult to judge whether the structure or piezoelectric lead zirconate titanate (PZT) is damaged when the signal changes. If the sensor fault occurs, the cases and degrees of the fault are unknown based on the electromechanical impedance method. Therefore, after the principal component analysis (PCA) of six characteristic indexes, a two-component solution which could explain 99.2% of the variance in the original indexes was obtained to judge whether the damage comes from the PZT. Then LibSVM was used to make an effective identification of four sensor faults (pseudo soldering, debonding, wear, and breakage) and their three damage degrees. The result shows that the identification accuracy of damaged PZT reached 97.5%. The absolute scores of PCA comprehensive evaluation for structural damages are less than 0.5 while for sensor faults are greater than 0.6. By comparing the scores of the samples under unknown conditions with the set threshold, whether the sensor faults occur is effectively judged; the intact and 12 possible damage states of PZT can be all classified correctly with the model trained by LibSVM. It is feasible to use LibSVM to classify the cases and degrees of sensor faults.


  • Open Access

    Piezoelectric Active Sensor Self‐Diagnosis for Electromechanical Impedance Monitoring Using K‐Means Clustering Analysis and Artificial Neural Network

    by Xie Jiang, Xin Zhang, Yuxiang Zhang

    Piezoelectric sensor is a crucial part of electromechanical impedance technology whose state will directly affect the effectiveness and accuracy of structural health monitoring (SHM). So carrying out sensor self‐diagnosis is important and necessary. However, it is still difficult to distinguish sensor faults from structural damage as well as identify the cases and degrees of sensor faults. In the study, three characteristic indexes of admittance which have different indication intervals for damages of structure and sensors were selected from six indexes after comparison. To improve the discrimination effect, three principal components (PC) were extracted by principal component analysis (PCA). And the damage information represented by PCs was clustered by the K‐means algorithm to identify the cases of damage. Then, the degrees of sensor damages were classified with the artificial neural network (ANN). The results show that the K‐means clustering analysis based on admittance characteristics can accurately distinguish and identify the structural damage and four kinds of sensor damages, namely, pseudosoldering, debonding, wear, and breakage. The trained ANN model has a good recognition effect on the damage degrees and the accuracy of recognition reaches 100%. This study has a certain reference value for piezoelectric sensor self‐fault identification.


  • Open Access

    Evaluation of Characterization Indexes and Minor Looseness Identification of Flange Bolt Under Noise Influence

    by Xie Jiang, Xin Zhang, Yuxiang Zhang

    Based on electromechanical impedance (EMI) technology, we studied the indication effect of each characterization index on flange bolt looseness under different noise levels. A new evaluation index T is constructed to solve the problem that the minor looseness and noise under the actual monitoring environment cannot be distinguished with existing indexes. The results show that among the five characterization indexes, the root mean square deviation (RMSD) and the correlation coefficient deviation (CCD) can reflect the minor looseness sensitively and are positively correlated with the degree of looseness. They also have good performance of looseness identification under the noise of 30 dBW. However, the indexes’ indication range of the case under 1 dBW-6 dBW noise overlaps with the case under 36 N·m-39.5 N·m torque. So it is impossible to judge the structure state with mere characterization indexes. Evaluation index T can extract the correlation difference of the conductance spectrum under the noise conditions and looseness conditions with the benchmark respectively. And there are different indication ranges of T on the noise and minor looseness. By determining a threshold and comparing T with it, whether bolt looseness occurs in an unknown condition can be effectively judged. Finally, T is applied to other flange structure with 8 bolts to verify the effectiveness and general applicability of the method. The evaluation index plays an important role in avoiding misjudgment of flange bolt caused by noise influence on minor looseness and improving the ability of identification when the bolt is at the critical state.


  • New serum biomarkers for detection of tuberculosis using surface-enhanced laser desorption/ionization time-of-flight mass spectrometry

    by Ji-Yan Liu, Lei Jin, Meng-Yuan Zhao, Xin Zhang, Chi-Bo Liu, Yu-Xiang Zhang, Fu-Jian Li, Jian-Min Zhou, Hua-Jun Wang, Ji-Cheng Li

    New technologies for the early detection of tuberculosis (TB) are urgently needed. Pathological changes within an organ might be reflected in proteomic patterns in serum. The aim of the present study was to screen for the potential protein biomarkers in serum for the diagnosis of TB using proteomic fingerprint technology. Proteomic fingerprint technology combining protein chips with surface-enhanced laser desorption/ionization time-of-flight mass spectrometry (SELDI-TOF MS) was used to profile the serum proteins from 50 patients with TB, 25 patients with lung disease other than TB, and 25 healthy volunteers. The protein fingerprint expression of all the serum samples and the resulting profiles between TB and control groups were analyzed with the Biomarker Wizard system. A total of 30 discriminating m/z peaks were detected that were related to TB (p<0.01). The model of biomarkers constructed by the Biomarker Patterns Software based on the three biomarkers (2024, 8007, and 8598 Da) generated excellent separation between the TB and control groups. The sensitivity was 84.0% and the specificity was 86.0%. Blind test data indicated a sensitivity of 80.0% and a specificity of 84.2%. The data suggested a potential application of SELDI-TOF MS as an effective technology to profile serum proteome, and with pattern analysis, a diagnostic model comprising three potential biomarkers was indicated to differentiate people with TB and healthy controls rapidly and precisely.