Yusuke Kawai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yusuke Kawai has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Kiyoshi Ohishi
Nagaoka University of Technology
4 shared publications - Yuki Yokokura
Nagaoka University of Technology
4 shared publications - Tadashi Tsubone
Nagaoka University of Technology
2 shared publications Toshimasa Miyazaki
Nagaoka Univ. of Tech
2 shared publicationsAtsushi Shimamoto
Unipulse Corporation, 9-11 Nihonbashihisamatsucho, Chuo-ku, Tokyo, 103-0005, JAPAN
1 shared publication- Kotaro Saito
Access network service systems laboratories, NTT Corporation, 1-7-1, Hanabatake, Tsukuba, Ibaraki, 305-0805, Japan
1 shared publication
Latest Publications
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 511-516
Quick Torsion Torque Control Based on Model Error Compensator and Disturbance Observer with Torsion Torque Sensor
Conventionally, I-P-I-P torsion torque control has been proposed for realizing the load-side acceleration control that is a robust motion control for the flexible joint manipulator. However, conventional torsion torque control is designed as a 4th-order delay system and it is difficult to improve the control bandwidth. For this, reducing control-system-order is required. This paper proposes a quick torsion torque control based on a force and position sensors integrated disturbance observer (FPIDO) and a model error compensator (MEC) for improving the performance of human interaction in the flexible joint manipulator. The proposed approach that combines the FPIDO and MEC is capable of control the design of the torsion torque control at the 2 nd -order delay system. The proposed approach is verified through numerical simulation and experimental results.
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 511-516
Quick Torsion Torque Control Based on Model Error Compensator and Disturbance Observer with Torsion Torque Sensor
Conventionally, I-P-I-P torsion torque control has been proposed for realizing the load-side acceleration control that is a robust motion control for the flexible joint manipulator. However, conventional torsion torque control is designed as a 4th-order delay system and it is difficult to improve the control bandwidth. For this, reducing control-system-order is required. This paper proposes a quick torsion torque control based on a force and position sensors integrated disturbance observer (FPIDO) and a model error compensator (MEC) for improving the performance of human interaction in the flexible joint manipulator. The proposed approach that combines the FPIDO and MEC is capable of control the design of the torsion torque control at the 2 nd -order delay system. The proposed approach is verified through numerical simulation and experimental results.
- 21 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (1) , 850-860
High-Robust Force Control for Environmental Stiffness Variation Based on Duality of Two-Inertia System
The conventional force control has proposed load-side torque control based on the resonance ratio control (RRC) enhanced by an instantaneous state observer using the acceleration sensor; however, environmental stiffness variation ( $K_e$ variation) is not considered in such systems. This paper evaluates the robust stability of the conventional method based on open-loop characteristics and the stability analysis results indicate that the conventional method becomes unstable during $K_e$ variation. To realize superior high-robust stability, this paper proposes a high-robust force control based on the duality of the two-inertia system. This paper constructs an equivalent RRC (ERRC) combining the motor-side velocity control and the load-side velocity observer and demonstrates a torque-velocity duality. The results confirm that the load-side torque control based on ERRC is robust against $K_e$ variation through the analysis of open-loop characteristics, and illustrate that the ERRC the same as the conventional RRC proposed in position or velocity controls. The effectiveness of the proposed control method is validated through numerical simulations and experiments.- 21 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (1) , 850-860
High-Robust Force Control for Environmental Stiffness Variation Based on Duality of Two-Inertia System
The conventional force control has proposed load-side torque control based on the resonance ratio control (RRC) enhanced by an instantaneous state observer using the acceleration sensor; however, environmental stiffness variation ( $K_e$ variation) is not considered in such systems. This paper evaluates the robust stability of the conventional method based on open-loop characteristics and the stability analysis results indicate that the conventional method becomes unstable during $K_e$ variation. To realize superior high-robust stability, this paper proposes a high-robust force control based on the duality of the two-inertia system. This paper constructs an equivalent RRC (ERRC) combining the motor-side velocity control and the load-side velocity observer and demonstrates a torque-velocity duality. The results confirm that the load-side torque control based on ERRC is robust against $K_e$ variation through the analysis of open-loop characteristics, and illustrate that the ERRC the same as the conventional RRC proposed in position or velocity controls. The effectiveness of the proposed control method is validated through numerical simulations and experiments.- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 3659-3664
Wideband Load-Side Acceleration Control Based on Load-Side Acceleration Sensing of Two-Inertia System
Load-side acceleration sensing based on load-side acceleration control is proposed for a two-inertia resonance system. The proposed method is divided into two stages. In the first stage, the feedback component from the load-side is canceled using the estimated value of the instantaneous state observer and the load-side acceleration. The two-inertia resonance system is converted into a simple second-order system using this method. The proposed method configures a control system of cascaded loops for the second-order system. Therefore, the load-side acceleration control is achieved by two specified bandwidths. The proposed method is easy to implement for conventional robots and yields superior cost-savings compared with other types of load-side acceleration control. The effectiveness of the proposed load-side acceleration controller is verified by theoretical analysis, numerical simulations, and experiments.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 3659-3664
Wideband Load-Side Acceleration Control Based on Load-Side Acceleration Sensing of Two-Inertia System
Load-side acceleration sensing based on load-side acceleration control is proposed for a two-inertia resonance system. The proposed method is divided into two stages. In the first stage, the feedback component from the load-side is canceled using the estimated value of the instantaneous state observer and the load-side acceleration. The two-inertia resonance system is converted into a simple second-order system using this method. The proposed method configures a control system of cascaded loops for the second-order system. Therefore, the load-side acceleration control is achieved by two specified bandwidths. The proposed method is easy to implement for conventional robots and yields superior cost-savings compared with other types of load-side acceleration control. The effectiveness of the proposed load-side acceleration controller is verified by theoretical analysis, numerical simulations, and experiments.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 001424-001429
Equivalence of resonance ratio and I-PD controllers in zero stiffness torque control for soft robot
Recently, a soft robot considering the contact of the human has attracted attention, and the zero stiffness torque control is required. Because a soft robot causes vibration at the load side, vibration suppression control of a soft robot is required. In this paper, the authors discuss position control and torque control of a soft robot by using a torsion torque sensor based on a resonance ratio control. Position control can be used to design parameters. However, torque control cannot be used to design parameters because the proportional gain Kp and resonance ratio gain Kr are not independent with regard to integral-proportional differential(I-PD) torque control. Therefore, in the case of torque control, resonance ratio control is equivalent to I-PD control.
- 1 November 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 001424-001429
Equivalence of resonance ratio and I-PD controllers in zero stiffness torque control for soft robot
Recently, a soft robot considering the contact of the human has attracted attention, and the zero stiffness torque control is required. Because a soft robot causes vibration at the load side, vibration suppression control of a soft robot is required. In this paper, the authors discuss position control and torque control of a soft robot by using a torsion torque sensor based on a resonance ratio control. Position control can be used to design parameters. However, torque control cannot be used to design parameters because the proportional gain Kp and resonance ratio gain Kr are not independent with regard to integral-proportional differential(I-PD) torque control. Therefore, in the case of torque control, resonance ratio control is equivalent to I-PD control.
- 15 January 2014
- Published by Springer Nature
- p. 109-119
Stability Transformation Method for Unstable Periodic Orbits and Its Realization
- 15 January 2014
- Published by Springer Nature
- p. 109-119
Stability Transformation Method for Unstable Periodic Orbits and Its Realization
- 1 January 2012
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in Nonlinear Theory and Its Applications, IEICE
- Vol. 3 (2) , 246-256
Chaos control based on stability Transformation method for unstable periodic orbits
- 1 January 2012
- Published by Institute of Electronics, Information and Communications Engineers (IEICE) in Nonlinear Theory and Its Applications, IEICE
- Vol. 3 (2) , 246-256
Chaos control based on stability Transformation method for unstable periodic orbits