Piotr Mańkowski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Piotr Mańkowski has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Sławomir Krzosek
Institute of Wood Sciences and Furniture, Warsaw University of Life Sciences-SGGW, Nowoursynowska 159, 02-776 Warsaw, Poland
6 shared publications - Izabela Burawska-Kupniewska
Department of Technology and Entrepreneurship in Wood Industry, Institute of Wood Sciences and Furniture, Warsaw University of Life Sciences—SGGW, 159 Nowoursynowska St., 02-776 Warsaw, Poland
5 shared publications - Agnieszka Laskowska
Warsaw University of Life Sciences – SGGW Institute of Wood Sciences and Furniture Department of Wood Science and Wood Preservation
2 shared publications - Marek Grześkiewicz
Institute of Wood Sciences and Furniture, Warsaw University of Life Sciences-SGGW, Nowoursynowska 159, 02-776 Warsaw, Poland
2 shared publications - Bogusław Andres
Department of Wood Science and Wood Protection, Institute of Wood Sciences and Furniture, Warsaw University of Life Sciences—SGGW, 159 Nowoursynowska St., 02-776 Warsaw, Poland
1 shared publication - Joanna Wyleżałek
Szkoła Główna Gospodarstwa Wiejskiego w Warszawie
1 shared publication
Latest Publications
- Open Access
Assessment of the Modulus of Rupture and Modulus of Elasticity in Static Bending of Yellow Pine Earlywood and Latewood
The purpose of this research was to investigate the modulus of rupture (MOR) and modulus of elasticity (MOE) in the static bending of yellow pine (Pinus ponderosa Douglas ex C. Lawson) earlywood and latewood. The relationship between the properties of these wood zones and the MOR and MOE of yellow pine wood tested was determined with the methodology specified in the standards. An important element of the research was to verify the suitability of the developed method for testing the MOR and MOE of small wood samples obtained from the earlywood and latewood zone. The MOR of the earlywood was about 6% higher than the MOR of the pine wood determined using standard samples, and these differences were not statistically significant. However, the MOR of the latewood was approximately three times higher than the MOR of the pine wood determined using standard samples, and these differences were statistically significant. The MOR of the latewood was found to be 2.5 times higher than the MOR of the earlywood. The MOE of the latewood was found to be two times higher than the MOE of the earlywood. This was due to the density of particular wood zones and the dimensions of structural elements—tracheids. The maximum load (Fmax) transferred by latewood zones was four times higher than the Fmax transferred by earlywood zones. The deflection at the Fmax of the earlywood zone was 20% smaller than the deflection at the Fmax of the latewood zone.
Open AccessAssessment of the Modulus of Rupture and Modulus of Elasticity in Static Bending of Yellow Pine Earlywood and Latewood
The purpose of this research was to investigate the modulus of rupture (MOR) and modulus of elasticity (MOE) in the static bending of yellow pine (Pinus ponderosa Douglas ex C. Lawson) earlywood and latewood. The relationship between the properties of these wood zones and the MOR and MOE of yellow pine wood tested was determined with the methodology specified in the standards. An important element of the research was to verify the suitability of the developed method for testing the MOR and MOE of small wood samples obtained from the earlywood and latewood zone. The MOR of the earlywood was about 6% higher than the MOR of the pine wood determined using standard samples, and these differences were not statistically significant. However, the MOR of the latewood was approximately three times higher than the MOR of the pine wood determined using standard samples, and these differences were statistically significant. The MOR of the latewood was found to be 2.5 times higher than the MOR of the earlywood. The MOE of the latewood was found to be two times higher than the MOE of the earlywood. This was due to the density of particular wood zones and the dimensions of structural elements—tracheids. The maximum load (Fmax) transferred by latewood zones was four times higher than the Fmax transferred by earlywood zones. The deflection at the Fmax of the earlywood zone was 20% smaller than the deflection at the Fmax of the latewood zone.
- Open Access
- 1 January 2024
- Published by Wydawnictwo Adam Marszalek in The New Educational Review
- Vol. 2024 (Vol. 78) , 28-38
Institutional forms of support for the intergenerational transmission of traditional skills as an intangible cultural heritage
Intangible cultural heritage includes values and social tradition, customs and practices of human activity. In the context of preserving the intangible cultural heritage, the authors of the article were interested in traditional skills related to woodworking of not only functional but also symbolic importance in different cultures. Due to the risks associated with the disappearance of traditional manufacturing, the authors decided to focus on support programs for local creators and craftsmen. The source of data presented in the article was qualitative research carried out as part of a research and dissemination project implemented under the Science for Society Programme.
- 1 January 2024
- Published by Wydawnictwo Adam Marszalek in The New Educational Review
- Vol. 2024 (Vol. 78) , 28-38
Open AccessInstitutional forms of support for the intergenerational transmission of traditional skills as an intangible cultural heritage
Intangible cultural heritage includes values and social tradition, customs and practices of human activity. In the context of preserving the intangible cultural heritage, the authors of the article were interested in traditional skills related to woodworking of not only functional but also symbolic importance in different cultures. Due to the risks associated with the disappearance of traditional manufacturing, the authors decided to focus on support programs for local creators and craftsmen. The source of data presented in the article was qualitative research carried out as part of a research and dissemination project implemented under the Science for Society Programme.
- 26 December 2023
- Published by Index Copernicus in Annals of WULS, Forestry and Wood Technology
- Vol. 124, 111-123
Traditional craft – dilemmas and challenges on the example of woodworking occupations
Traditional craft – dilemmas and challenges on the example of woodworking occupationsThe article focuses on the social perception of woodworking, the knowledge Poles have on the related customs and occupations (in the past and at present), potential interest in workshops and training courses connected with woodworking, and the purchase of wood products manufactured in a traditional way. A quantitative study was prepared based on direct interviews which were conducted with the use of electronic equipment, the Computer Assisted Personal Interview (CAPI/MOBI) on a representative, random and quota sampling of adult Poles (N=1000). The research results showed that there is a significant social and cultural value in preserving traditional skills connected with woodworking, which translates into social readiness to support such traditions through education as well as buyer preferences. While a clear majority of respondents demonstrate a very low level of knowledge about woodworking occupations and related traditions (both about the past and present), being equipped with the same determines to a large extent individuals’ propensity to purchase wooden products traditionally made. Therefore, the social argument for educating about former occupations, customs, traditions and skills connected with woodworking is of crucial importance. The article was written under the Minister of Science and Education's Science for Society Programme as part of the project entitled “(Non-) Surviving occupations, skills and customs in rural communities of the Mazowsze Region and Eastern Poland” (NdS/536514/2021/2021)
- 26 December 2023
- Published by Index Copernicus in Annals of WULS, Forestry and Wood Technology
- Vol. 124, 111-123
Traditional craft – dilemmas and challenges on the example of woodworking occupations
Traditional craft – dilemmas and challenges on the example of woodworking occupationsThe article focuses on the social perception of woodworking, the knowledge Poles have on the related customs and occupations (in the past and at present), potential interest in workshops and training courses connected with woodworking, and the purchase of wood products manufactured in a traditional way. A quantitative study was prepared based on direct interviews which were conducted with the use of electronic equipment, the Computer Assisted Personal Interview (CAPI/MOBI) on a representative, random and quota sampling of adult Poles (N=1000). The research results showed that there is a significant social and cultural value in preserving traditional skills connected with woodworking, which translates into social readiness to support such traditions through education as well as buyer preferences. While a clear majority of respondents demonstrate a very low level of knowledge about woodworking occupations and related traditions (both about the past and present), being equipped with the same determines to a large extent individuals’ propensity to purchase wooden products traditionally made. Therefore, the social argument for educating about former occupations, customs, traditions and skills connected with woodworking is of crucial importance. The article was written under the Minister of Science and Education's Science for Society Programme as part of the project entitled “(Non-) Surviving occupations, skills and customs in rural communities of the Mazowsze Region and Eastern Poland” (NdS/536514/2021/2021)
- 29 March 2023
- Published by Index Copernicus in Annals of WULS, Forestry and Wood Technology
- Vol. 121, 135-141
Relationship between the compressive strength, density and the width of the annual rings in a high-guality part of timber of Scots pine (Pinus sylvestris L.) wood
Investigation of round Scots pine wood WC01 class using X-ray computer tomography. Scots pine is the most widespread type of wood in Poland with wide industrial use. The typical starting material used for the production of layered floor elements are logs of WC01 class (class according to the Polish Standard PN-D-95008: 1992 and Order no 72 - GM-900-5 / 2013 of General Director of the State Forests in Poland). Using X-ray computed tomography, tests of fresh wood in the bark were carried out, confirming the full suitability of this technique for the precise assessment of wood density as well as its grain and distribution of anatomical defects (knots). The different level of humidity of sapwood and heartwood in fresh wood is visible in tomographic images and translates into a much higher recorded density of the wetter zone of sapwood. Calibration of the tomograph used made it possible to convert the Hounsfield density scale into actual densities expressed in kg/m3.
- 29 March 2023
- Published by Index Copernicus in Annals of WULS, Forestry and Wood Technology
- Vol. 121, 135-141
Relationship between the compressive strength, density and the width of the annual rings in a high-guality part of timber of Scots pine (Pinus sylvestris L.) wood
Investigation of round Scots pine wood WC01 class using X-ray computer tomography. Scots pine is the most widespread type of wood in Poland with wide industrial use. The typical starting material used for the production of layered floor elements are logs of WC01 class (class according to the Polish Standard PN-D-95008: 1992 and Order no 72 - GM-900-5 / 2013 of General Director of the State Forests in Poland). Using X-ray computed tomography, tests of fresh wood in the bark were carried out, confirming the full suitability of this technique for the precise assessment of wood density as well as its grain and distribution of anatomical defects (knots). The different level of humidity of sapwood and heartwood in fresh wood is visible in tomographic images and translates into a much higher recorded density of the wetter zone of sapwood. Calibration of the tomograph used made it possible to convert the Hounsfield density scale into actual densities expressed in kg/m3.
- Open Access
Influence of Thermo-Mechanical Densification (TMD) on the Properties of Structural Sawn Timber (Pinus sylvestris L.)
The article presents the results of thermo-mechanical densification tests conducted on Scots pine timber. The densification process was carried out in industrial conditions with a high-pressure press, which allowed flat compression of boards that were up to 2.5 m long. A phenomenon of elastic redeformations was observed in the densified boards after each pulse of compression. As a result of thermo-mechanical compression, the average timber moisture content dropped to 9%, and the average density increased by 13.5%, from the level of 547 to 621 kg/m3. As a result of thermo-mechanical densification, the strength class C of most Scots pine timber pieces improved. Most timber pieces that were subjected to thermo-mechanical densification have improved their strength class, C, by one (72.7% of the tested batch) or two C classes (3.6% of the batch under study).
Open AccessInfluence of Thermo-Mechanical Densification (TMD) on the Properties of Structural Sawn Timber (Pinus sylvestris L.)
The article presents the results of thermo-mechanical densification tests conducted on Scots pine timber. The densification process was carried out in industrial conditions with a high-pressure press, which allowed flat compression of boards that were up to 2.5 m long. A phenomenon of elastic redeformations was observed in the densified boards after each pulse of compression. As a result of thermo-mechanical compression, the average timber moisture content dropped to 9%, and the average density increased by 13.5%, from the level of 547 to 621 kg/m3. As a result of thermo-mechanical densification, the strength class C of most Scots pine timber pieces improved. Most timber pieces that were subjected to thermo-mechanical densification have improved their strength class, C, by one (72.7% of the tested batch) or two C classes (3.6% of the batch under study).
- Open Access
Efficiency of Visual and Machine Strength Grading of Sawn Timber with Respect to Log Type
A batch of pine timber sawn from butt, middle and top logs was strength graded with the visual method (classification into grading classes KW—best quality, KS—medium quality, KG—inferior quality and Reject) and with the machine strength grading method—performed with the use of a mobile timber grader (classification into C strength classes). We compared the efficiency of grading classes and strength classes, depending on the type of log from which the material was obtained (butt, middle, top). Next, a strength grading machine was used to measure the modulus of elasticity in bending (MOE) and static bending strength (MOR). The ANOVA confirmed the influence of both the log type (butt, middle, top), the C strength class, and the visual strength grading class on the values of density (DEN) and MOR. Timber density and MOR decreased from the butt log section to the top log section. The ANOVA confirmed the influence of log type on MOE values, but only to a limited extent.
Open AccessEfficiency of Visual and Machine Strength Grading of Sawn Timber with Respect to Log Type
A batch of pine timber sawn from butt, middle and top logs was strength graded with the visual method (classification into grading classes KW—best quality, KS—medium quality, KG—inferior quality and Reject) and with the machine strength grading method—performed with the use of a mobile timber grader (classification into C strength classes). We compared the efficiency of grading classes and strength classes, depending on the type of log from which the material was obtained (butt, middle, top). Next, a strength grading machine was used to measure the modulus of elasticity in bending (MOE) and static bending strength (MOR). The ANOVA confirmed the influence of both the log type (butt, middle, top), the C strength class, and the visual strength grading class on the values of density (DEN) and MOR. Timber density and MOR decreased from the butt log section to the top log section. The ANOVA confirmed the influence of log type on MOE values, but only to a limited extent.
- Open Access
- 1 August 2021
- Published by Universidad del Bio Bio in Maderas. Ciencia y Tecnología
- Vol. 23
Compressive strength parallel to grain of earlywood and latewood of yellow pine
The compressive strength parallel to grain of earlywood and latewood from the yellow pine sapwood and heartwood areas was examined in the study. The structure of the basic anatomical elements of wood - tracheids, which conduct water and/or perform the mechanical function - was also characterized. The compressive strength parallel to grain of latewood in the sapwood area was found to be twice as high as the compressive strength parallel to grain of earlywood. The compressive strength parallel to grain of latewood in the heartwood area, on the other hand, was found to be 2,5 times higher than the compressive strength parallel to grain of earlywood. This was due to the density of particular areas of wood and the dimensions of structural elements - tracheids. In the sapwood area, the density of latewood was ca. twice as high as the density of earlywood. Similar relationships were found for heartwood. The thickness of latewood tracheids was found to be 1,5 times greater than the thickness of earlywood tracheids. These relationships were observed in sapwood and heartwood. The diameter of earlywood tracheids in radial direction was twice as large as the diameter of latewood tracheids. These relationships were observed in yellow pine sapwood and heartwood.
- 1 August 2021
- Published by Universidad del Bio Bio in Maderas. Ciencia y Tecnología
- Vol. 23
Open AccessCompressive strength parallel to grain of earlywood and latewood of yellow pine
The compressive strength parallel to grain of earlywood and latewood from the yellow pine sapwood and heartwood areas was examined in the study. The structure of the basic anatomical elements of wood - tracheids, which conduct water and/or perform the mechanical function - was also characterized. The compressive strength parallel to grain of latewood in the sapwood area was found to be twice as high as the compressive strength parallel to grain of earlywood. The compressive strength parallel to grain of latewood in the heartwood area, on the other hand, was found to be 2,5 times higher than the compressive strength parallel to grain of earlywood. This was due to the density of particular areas of wood and the dimensions of structural elements - tracheids. In the sapwood area, the density of latewood was ca. twice as high as the density of earlywood. Similar relationships were found for heartwood. The thickness of latewood tracheids was found to be 1,5 times greater than the thickness of earlywood tracheids. These relationships were observed in sapwood and heartwood. The diameter of earlywood tracheids in radial direction was twice as large as the diameter of latewood tracheids. These relationships were observed in yellow pine sapwood and heartwood.
- Open Access
Mechanical Properties of Machine Stress Graded Sawn Timber Depending on the Log Type
This article presents the results of tests conducted on Scots pine timber from three different kinds of logs: butt, middle and top. A planed pine timber batch composed of 510 pieces, dried to ca. 12% humidity, was machine-graded using a portable MTG device, and classified into the following classes: C18, C24, C30, C35 and C40 (according to EN 338:2016). During the second stage of the study, the timber was tested to determine its density, MOE and MOR, in accordance with EN 408:2012. We analyzed the impact of the timber’s log of origin on the results of machine strength grading and on the values of correlation coefficients between the tested properties. The results show, among others, that there is a correlation between the C classes and MOR of the tested timber, as well as its origin from butt, middle or top logs.
Open AccessMechanical Properties of Machine Stress Graded Sawn Timber Depending on the Log Type
This article presents the results of tests conducted on Scots pine timber from three different kinds of logs: butt, middle and top. A planed pine timber batch composed of 510 pieces, dried to ca. 12% humidity, was machine-graded using a portable MTG device, and classified into the following classes: C18, C24, C30, C35 and C40 (according to EN 338:2016). During the second stage of the study, the timber was tested to determine its density, MOE and MOR, in accordance with EN 408:2012. We analyzed the impact of the timber’s log of origin on the results of machine strength grading and on the values of correlation coefficients between the tested properties. The results show, among others, that there is a correlation between the C classes and MOR of the tested timber, as well as its origin from butt, middle or top logs.
- 31 December 2020
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
- Vol. 63 (206) , 63-76
THE SUSCEPTIBILITY OF SCOTS PINE HEARTWOOD FROM VARIOUS POLISH FORESTRY REGIONS TO THE BROWN ROT FUNGUS CONIOPHORA PUTEANA (SCHUMACH.) P. KARST.
- 31 December 2020
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
- Vol. 63 (206) , 63-76
THE SUSCEPTIBILITY OF SCOTS PINE HEARTWOOD FROM VARIOUS POLISH FORESTRY REGIONS TO THE BROWN ROT FUNGUS CONIOPHORA PUTEANA (SCHUMACH.) P. KARST.
- Open Access
The Influence of Scots Pine Log Type (Pinus sylvestris L.) on the Mechanical Properties of Lumber
The paper presents an analysis of the influence of geographical origin and Scots pine log type on the mechanical properties of the timber sawn from them. The tested timber was sawn from logs obtained from three different forestry regions in Poland, located in the western part of the country. A batch of 150 timber pieces was obtained from each region. The cross-section had the dimensions of 40 mm × 138 mm. The timber was sawn from logs of three different types: butt, middle and top, from a fresh, mixed forest around 120 years old. The timber was dried in industrial conditions and planed four times. The values determined for the timber under research were the static modulus of elasticity in bending (MOE), and the bending strength (MOR). Moreover, timber density (DEN) was determined with the stereometric method. For all three sites, the highest average values of the tested timber properties were obtained for timber made of butt logs, and the lowest for timber made of top logs. It was concluded that the tested Scots pine properties depended on the type of log, and to limited extent, on its geographic origin. The statistical analysis revealed that the geographic origin of the logs that the tested timber was made of had a statistically significant impact on the variance of all the tested timber properties. The type of log also had a statistically significant influence on the variance of all the tested properties.
Open AccessThe Influence of Scots Pine Log Type (Pinus sylvestris L.) on the Mechanical Properties of Lumber
The paper presents an analysis of the influence of geographical origin and Scots pine log type on the mechanical properties of the timber sawn from them. The tested timber was sawn from logs obtained from three different forestry regions in Poland, located in the western part of the country. A batch of 150 timber pieces was obtained from each region. The cross-section had the dimensions of 40 mm × 138 mm. The timber was sawn from logs of three different types: butt, middle and top, from a fresh, mixed forest around 120 years old. The timber was dried in industrial conditions and planed four times. The values determined for the timber under research were the static modulus of elasticity in bending (MOE), and the bending strength (MOR). Moreover, timber density (DEN) was determined with the stereometric method. For all three sites, the highest average values of the tested timber properties were obtained for timber made of butt logs, and the lowest for timber made of top logs. It was concluded that the tested Scots pine properties depended on the type of log, and to limited extent, on its geographic origin. The statistical analysis revealed that the geographic origin of the logs that the tested timber was made of had a statistically significant impact on the variance of all the tested timber properties. The type of log also had a statistically significant influence on the variance of all the tested properties.