Audrey D. Scholz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Audrey D. Scholz has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
Amanda L. Stewart
Chemistry Department, Georgia Southern University, USA
1 shared publication- Brian V. Khau
School of Chemical and Biomolecular Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332, United States
1 shared publication - Elsa Reichmanis
Lehigh University
1 shared publication Michael A. Bachan
Chemistry Department, Georgia Southern University, USA
1 shared publication- Rafael Lopes Quirino
Chemistry Department, Georgia Southern University, Statesboro, GA 30458, USA
1 shared publication Russell L. Lewis
Chemistry Department, Georgia Southern University, USA
1 shared publication
Latest Publications
- 22 September 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (43) , 15067-15078
Advances and opportunities in development of deformable organic electrochemical transistors
Unlocking deformability in organic electrochemical transistors (OECTs) is critical for their integration into wearable or implantable electronics, necessitating technological advances at the component and transistor levels.
- 22 September 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 8 (43) , 15067-15078
Advances and opportunities in development of deformable organic electrochemical transistors
Unlocking deformability in organic electrochemical transistors (OECTs) is critical for their integration into wearable or implantable electronics, necessitating technological advances at the component and transistor levels.
- 2 May 2017
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 1 (9) , 1795-1803
Biocomposites from the reinforcement of a tung oil-based thermosetting resin with collagen
Collagen from three different sources has been added to a tung oil-based thermosetting resin in order to enhance its mechanical properties for possible applications in the biomedical field as materials directly derived from biological molecules. The thermosets prepared in this work are made using tung oil, divinylbenzene (DVB), n-butyl methacrylate (BMA), tert-butyl peroxide (TBPO), asolectin, and collagen types I and III. Composites containing up to 5.0 wt% of collagen have been successfully prepared and characterized by dielectric analysis (DEA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The structure of the collagen samples used in this work was investigated through circular dichroism (CD) spectroscopy. Dynamic mechanical analysis (DMA) was used to assess composites' mechanical properties and revealed an improvement in the storage modulus at room temperature with increasing amounts of collagen, reaching an impressive increase of ∼100% for composites containing 5.0 wt% of collagen extracted from beef tendons in comparison to the unreinforced resin. The results indicate that collagen exhibits a reinforcing behavior similar to that obtained with nanostructured materials, such as carbon nanotubes for instance, therefore working as an effective reinforcement for the preparation of biocomposites.
- 2 May 2017
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 1 (9) , 1795-1803
Biocomposites from the reinforcement of a tung oil-based thermosetting resin with collagen
Collagen from three different sources has been added to a tung oil-based thermosetting resin in order to enhance its mechanical properties for possible applications in the biomedical field as materials directly derived from biological molecules. The thermosets prepared in this work are made using tung oil, divinylbenzene (DVB), n-butyl methacrylate (BMA), tert-butyl peroxide (TBPO), asolectin, and collagen types I and III. Composites containing up to 5.0 wt% of collagen have been successfully prepared and characterized by dielectric analysis (DEA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The structure of the collagen samples used in this work was investigated through circular dichroism (CD) spectroscopy. Dynamic mechanical analysis (DMA) was used to assess composites' mechanical properties and revealed an improvement in the storage modulus at room temperature with increasing amounts of collagen, reaching an impressive increase of ∼100% for composites containing 5.0 wt% of collagen extracted from beef tendons in comparison to the unreinforced resin. The results indicate that collagen exhibits a reinforcing behavior similar to that obtained with nanostructured materials, such as carbon nanotubes for instance, therefore working as an effective reinforcement for the preparation of biocomposites.