Jesús A. Sandoval-Robles
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jesús A. Sandoval-Robles has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Ciro Angel Rodriguez
Tecnologico de Monterrey, Monterrey, Mexico
3 shared publications - Erika García-López
Tecnologico de Monterrey, Monterrey, Mexico
3 shared publications - Elisa Vazquez-Lepe
Tecnologico de Monterrey, Monterrey, Mexico
2 shared publications - Luis D. Cedeño-Viveros
Tecnologico de Monterrey, Monterrey, Mexico
2 shared publications - Mariana Macías-Naranjo
Tecnologico de Monterrey, Monterrey, Mexico
2 shared publications - Ricardo Osorio
Tecnologico de Monterrey, Monterrey, Mexico
2 shared publications
Latest Publications
- Open Access
- 26 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 4579-4581
Publisher Correction: Laser polishing for surface enhancement of AISI 316 L parts fabricated by laser powder bed fusion
- 26 February 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (4) , 4579-4581
Open AccessPublisher Correction: Laser polishing for surface enhancement of AISI 316 L parts fabricated by laser powder bed fusion
- Open Access
- 14 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (3) , 2781-2799
Laser polishing for surface enhancement of AISI 316 L parts fabricated by laser powder bed fusion
- 14 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (3) , 2781-2799
Open AccessLaser polishing for surface enhancement of AISI 316 L parts fabricated by laser powder bed fusion
- Open Access
Laser Surface Texturing and Electropolishing of CoCr and Ti6Al4V-ELI Alloys for Biomedical Applications
The interplay between a prosthetic and tissue represents an important factor for the fixation of orthopedic implants. Laser texturing tests and electropolishing were performed on two materials used in the fabrication of medical devices, i.e., CoCr and Ti6Al4V-ELI alloys. The material surface was textured with a diode-pumped solid state (DPSS) laser and its effect on the surface quality and material modification, under different combinations of laser power and marking speed, were investigated. Our results indicate that an increment of energy per unit length causes an incremental trend in surface roughness parameters. Additionally, phase transformation on the surface of both alloys was achieved. Chemical analysis by energy dispersive X-ray spectrometer (EDX) shows the formation of (Co(Cr,Mo)) phase and the M23C6 precipitate on the CoCr surface; while quantitative analysis of the X-ray diffractometer (XRD) results demonstrates the oxidation of the Ti alloy with the formation of Ti2O and Ti6O from the reduction of the α-Ti phase. The behaviors were both related with an increase of the energy per unit length. Control of the final surface roughness was achieved by an electropolishing post-treatment, minimizing the as-treated values. After polishing, a reduction of surface roughness parameters was obtained in a range between 3% and 44%, while no changes in chemical composition or present phases were observed.
Open AccessLaser Surface Texturing and Electropolishing of CoCr and Ti6Al4V-ELI Alloys for Biomedical Applications
The interplay between a prosthetic and tissue represents an important factor for the fixation of orthopedic implants. Laser texturing tests and electropolishing were performed on two materials used in the fabrication of medical devices, i.e., CoCr and Ti6Al4V-ELI alloys. The material surface was textured with a diode-pumped solid state (DPSS) laser and its effect on the surface quality and material modification, under different combinations of laser power and marking speed, were investigated. Our results indicate that an increment of energy per unit length causes an incremental trend in surface roughness parameters. Additionally, phase transformation on the surface of both alloys was achieved. Chemical analysis by energy dispersive X-ray spectrometer (EDX) shows the formation of (Co(Cr,Mo)) phase and the M23C6 precipitate on the CoCr surface; while quantitative analysis of the X-ray diffractometer (XRD) results demonstrates the oxidation of the Ti alloy with the formation of Ti2O and Ti6O from the reduction of the α-Ti phase. The behaviors were both related with an increase of the energy per unit length. Control of the final surface roughness was achieved by an electropolishing post-treatment, minimizing the as-treated values. After polishing, a reduction of surface roughness parameters was obtained in a range between 3% and 44%, while no changes in chemical composition or present phases were observed.