Syed Wilayat Husain
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Syed Wilayat Husain has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Khaliq
College of Engineering, University of Ha’il, Ha’il P.O. Box 2440, Saudi Arabia
1 shared publication - Abdul Wadood
Department of Materials Science and Engineering, Institute of Space Technology Islamabad, Islamabad 44000, Pakistan
1 shared publication Aliya Zahid
Department of Chemistry, Government College University, Lahore, 54000, Pakistan
1 shared publication- Amtul Basit
Department of Materials Science and Engineering, Institute of Space Technology, Islamabad, 44000, Pakistan
1 shared publication - Anjum Tauqir
Dept. of Materials Science and Engineering Institute of Space Technology 44000 Islamabad Pakistan
1 shared publication Beenish Shoukat
Department of Materials Science and Engineering, Institute of Space Technology, Islamabad, 44000, Pakistan
1 shared publication
Latest Publications
- 1 January 2025
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 42, 239-250
Effect of double ageing heat treatment on microstructure of Cu-Cr-Zr alloy
In this study, the Cu-0.78Cr-0.18Zr alloy was investigated for microstructural features in as-forged, aged and double aged conditions. This alloy was characterized by optical emission spectroscopy (OES), optical microscopy (OM), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Formation of various phases and their morphology was studied using field emission scanning electron microscope (FE-SEM). Experimental results showed that the alloy in forged condition exhibited grain sizes ranging from 7.5-82 µm, with an average grain size of 33.05 µm. In aged condition, it mainly composed of four types of phases i.e. Cu-matrix, Zr rich (Cu-Zr) precipitates, Cr rich (Pure Cr and Cr-Cu) precipitates and Cu-Cr-Zr ternary precipitates. In single aged condition, Cu5CrZr precipitates were spotted with ellipsoidal morphology. Tiny pure Cr precipitates always showed spherical shape while Cr-rich precipitates appeared in spherical and ellipsoidal shape in single aged condition, while in double aged condition, in addition to these forms it also displayed elongated morphology. Zr rich precipitates always formed with nodular morphology.
- 1 January 2025
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 42, 239-250
Effect of double ageing heat treatment on microstructure of Cu-Cr-Zr alloy
In this study, the Cu-0.78Cr-0.18Zr alloy was investigated for microstructural features in as-forged, aged and double aged conditions. This alloy was characterized by optical emission spectroscopy (OES), optical microscopy (OM), scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Formation of various phases and their morphology was studied using field emission scanning electron microscope (FE-SEM). Experimental results showed that the alloy in forged condition exhibited grain sizes ranging from 7.5-82 µm, with an average grain size of 33.05 µm. In aged condition, it mainly composed of four types of phases i.e. Cu-matrix, Zr rich (Cu-Zr) precipitates, Cr rich (Pure Cr and Cr-Cu) precipitates and Cu-Cr-Zr ternary precipitates. In single aged condition, Cu5CrZr precipitates were spotted with ellipsoidal morphology. Tiny pure Cr precipitates always showed spherical shape while Cr-rich precipitates appeared in spherical and ellipsoidal shape in single aged condition, while in double aged condition, in addition to these forms it also displayed elongated morphology. Zr rich precipitates always formed with nodular morphology.
- Open Access
- 30 October 2020
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 38 (5) , 493-501
Optimization of Friction Stir Welding Parameters of AA2014-T6 Alloy using Taguchi Statistical Approach
In this study, the Taguchi Design of Experiment method was used to determine the optimal Friction Stir Welding (FSW) parameters for improving the mechanical properties of AA 2014-T6 alloy butt joints. The three most significant parameters-tool rotational speed, tool linear travel speed and tool tilt angle-were optimized using the L9 orthogonal array design. The optimal welding parameters for the maximum tensile strength were determined by analyzing the signal-to-noise (S/N) ratio. A regression model was developed for the desired responses. The optimal tensile strength was achieved at the 1000 rpm, rotational speed, 600 mm/rev welding speed, and 2 ° tool title angle. The results were confirmed using a steady-state heat transfer model generated from the COMSOL Multiphysics Finite Element software. The identified optimal conditions were verified by experimental validation tests. The experimental results were consistent with the predicted values. Analysis of variance (ANOVA) was conducted to determine the effects of individual parameters and to identify the most significant process parameter. ANOVA indicated that the most significant factor affecting the mechanical behavior of the joint was the tool rotation speed followed by the linear travel speed.
- 30 October 2020
- Published by The Korean Welding and Joining Society in Journal of Welding and Joining
- Vol. 38 (5) , 493-501
Open AccessOptimization of Friction Stir Welding Parameters of AA2014-T6 Alloy using Taguchi Statistical Approach
In this study, the Taguchi Design of Experiment method was used to determine the optimal Friction Stir Welding (FSW) parameters for improving the mechanical properties of AA 2014-T6 alloy butt joints. The three most significant parameters-tool rotational speed, tool linear travel speed and tool tilt angle-were optimized using the L9 orthogonal array design. The optimal welding parameters for the maximum tensile strength were determined by analyzing the signal-to-noise (S/N) ratio. A regression model was developed for the desired responses. The optimal tensile strength was achieved at the 1000 rpm, rotational speed, 600 mm/rev welding speed, and 2 ° tool title angle. The results were confirmed using a steady-state heat transfer model generated from the COMSOL Multiphysics Finite Element software. The identified optimal conditions were verified by experimental validation tests. The experimental results were consistent with the predicted values. Analysis of variance (ANOVA) was conducted to determine the effects of individual parameters and to identify the most significant process parameter. ANOVA indicated that the most significant factor affecting the mechanical behavior of the joint was the tool rotation speed followed by the linear travel speed.