Joel V. Bernier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Joel V. Bernier has a total of 114 co-authors. Here are the top co-authors by number of shared publications:
- Rachel E. Lim
Materials Science Division, Lawrence Livermore National Laboratory 1 , Livermore, California 94550
5 shared publications - Anthony D. Rollett
Carnegie Mellon University
3 shared publications - Federica Coppari
Lawrence Livermore National Laboratory
3 shared publications - Jon H. Eggert
Lawrence Livermore National Laboratory 1 , Livermore, California 94550
3 shared publications - Marius Millot
Lawrence Livermore National Laboratory 1 , Livermore, California 94550
3 shared publications - Amy Lazicki
Lawrence Livermore National Laboratory, Livermore, USA
2 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (1)
Time-resolved X-ray diffraction diagnostic development for the National Ignition Facility
We present the development of an experimental platform that can collect four frames of x-ray diffraction data along a single line of sight during laser-driven, dynamic-compression experiments at the National Ignition Facility. The platform is comprised of a diagnostic imager built around ultrafast sensors with a 2-ns integration time, a custom target assembly that serves also to shield the imager, and a 10-ns duration, quasi-monochromatic x-ray source produced by laser-generated plasma. We demonstrate the performance with diffraction data for Pb ramp compressed to 150 GPa and illuminated by a Ge x-ray source that produces ∼7 × 1011, 10.25-keV photons/ns at the 400 μm diameter sample.
- 1 January 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (1)
Open AccessTime-resolved X-ray diffraction diagnostic development for the National Ignition Facility
We present the development of an experimental platform that can collect four frames of x-ray diffraction data along a single line of sight during laser-driven, dynamic-compression experiments at the National Ignition Facility. The platform is comprised of a diagnostic imager built around ultrafast sensors with a 2-ns integration time, a custom target assembly that serves also to shield the imager, and a 10-ns duration, quasi-monochromatic x-ray source produced by laser-generated plasma. We demonstrate the performance with diffraction data for Pb ramp compressed to 150 GPa and illuminated by a Ge x-ray source that produces ∼7 × 1011, 10.25-keV photons/ns at the 400 μm diameter sample.
- Open Access
- 10 October 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-9
The influence of alloying on slip intermittency and the implications for dwell fatigue in titanium
Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti–7Al–O alloys. This shows that the detrimental effect of precipitation of ordered Ti3Al is to increase the magnitude of rare pri〈a〉 and bas〈a〉 slip bursts associated with slip localisation. By contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of slip bursts and promoting a higher frequency of smaller events. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.
- 10 October 2022
- Published by Springer Nature in Nature Communications
- Vol. 13 (1) , 1-9
Open AccessThe influence of alloying on slip intermittency and the implications for dwell fatigue in titanium
Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti–7Al–O alloys. This shows that the detrimental effect of precipitation of ordered Ti3Al is to increase the magnitude of rare pri〈a〉 and bas〈a〉 slip bursts associated with slip localisation. By contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of slip bursts and promoting a higher frequency of smaller events. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.
- Open Access
- 1 October 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (10) , 103302
X-ray source characterization and sample heating on x-ray diffraction experiments at the National Ignition Facility
X-ray diffraction is a powerful measurement technique for determining material properties, and it is now possible to perform these experiments at pressures exceeding 1 TPa [Rygg et al., Rev. Sci. Instrum. 91, 043902 (2020)] at the National Ignition Facility (NIF). The x-ray source for these experiments is the quasi-monochromatic Heα emission from metal foils heated to multi-keV temperatures. A critical aspect for understanding the sample's thermodynamic state is the amount of heating caused by absorption of the probe x-rays. In this work, we characterize the performance of the Ge foil x-ray source over more than 60 NIF x-ray diffraction experiments. We use this information to constrain the level of diffraction sample heating from the x-ray source and discuss the impact on the thermodynamic state.
- 1 October 2022
- Published by AIP Publishing in Physics of Plasmas
- Vol. 29 (10) , 103302
Open AccessX-ray source characterization and sample heating on x-ray diffraction experiments at the National Ignition Facility
X-ray diffraction is a powerful measurement technique for determining material properties, and it is now possible to perform these experiments at pressures exceeding 1 TPa [Rygg et al., Rev. Sci. Instrum. 91, 043902 (2020)] at the National Ignition Facility (NIF). The x-ray source for these experiments is the quasi-monochromatic Heα emission from metal foils heated to multi-keV temperatures. A critical aspect for understanding the sample's thermodynamic state is the amount of heating caused by absorption of the probe x-rays. In this work, we characterize the performance of the Ge foil x-ray source over more than 60 NIF x-ray diffraction experiments. We use this information to constrain the level of diffraction sample heating from the x-ray source and discuss the impact on the thermodynamic state.
- Open Access
The influence of alloying on slip intermittency and the implications for dwell fatigue in titanium
Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti-7Al-O alloys. This shows that the detrimental effect of precipitation of ordered Ti_3Al is to increase the magnitude of rare pri and bas slip bursts associated with slip localisation. In contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of bas slip bursts and increasing the homogeneity between basal and prismatic slip. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.
Open AccessThe influence of alloying on slip intermittency and the implications for dwell fatigue in titanium
Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti-7Al-O alloys. This shows that the detrimental effect of precipitation of ordered Ti_3Al is to increase the magnitude of rare pri and bas slip bursts associated with slip localisation. In contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of bas slip bursts and increasing the homogeneity between basal and prismatic slip. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.
- 1 March 2022
- Published by Elsevier in International Journal of Fatigue
- Vol. 156, 106614
Grain reorientation and stress-state evolution during cyclic loading of an -Ti alloy below the elastic limit- 1 March 2022
- Published by Elsevier in International Journal of Fatigue
- Vol. 156, 106614
Grain reorientation and stress-state evolution during cyclic loading of an -Ti alloy below the elastic limit- Top Cited Papers
- 14 January 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 375 (6577) , 202-205
Measuring the melting curve of iron at super-Earth core conditions
Terapascal iron-melting temperature: The pressure and temperature conditions at which iron melts are important for terrestrial planets because they determine the size of the liquid metal core, an important factor for understanding the potential for generating a radiation-shielding magnetic field. Kraus et al . used laser-driven shock to determine the iron-melt curve up to a pressure of 1000 gigapascals (see the Perspective by Zhang and Lin). This value is about three times that of the Earth’s inner core boundary. The authors found that the liquid metal core lasted the longest for Earth-like planets four to six times larger in mass than the Earth. —BG
- 14 January 2022
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 375 (6577) , 202-205
Top Cited PapersMeasuring the melting curve of iron at super-Earth core conditions
Terapascal iron-melting temperature: The pressure and temperature conditions at which iron melts are important for terrestrial planets because they determine the size of the liquid metal core, an important factor for understanding the potential for generating a radiation-shielding magnetic field. Kraus et al . used laser-driven shock to determine the iron-melt curve up to a pressure of 1000 gigapascals (see the Perspective by Zhang and Lin). This value is about three times that of the Earth’s inner core boundary. The authors found that the liquid metal core lasted the longest for Earth-like planets four to six times larger in mass than the Earth. —BG
- Open Access
- 1 November 2021
- Published by Elsevier in Materials & Design
- Vol. 210
Interpretation of intragranular strain fields in high-energy synchrotron X-ray experiments via finite element simulations and analysis of incompatible deformation
- 1 November 2021
- Published by Elsevier in Materials & Design
- Vol. 210
Open AccessInterpretation of intragranular strain fields in high-energy synchrotron X-ray experiments via finite element simulations and analysis of incompatible deformation
- Open Access
- 23 August 2021
- Published by Taylor & Francis in Materials Research Letters
- Vol. 9 (10) , 429-436
High speed synchrotron X-ray diffraction experiments resolve microstructure and phase transformation in laser processed Ti-6Al-4V
The microstructures of Ti-6Al-4V following laser processing depend primarily on the phase transformation of β to α, but their development is constrained by the rapidly changing temperature in the small fusion zone. In-situ synchrotron X-ray diffraction was utilized to probe the rapid phase evolution in single melt tracks with high angular and temporal resolution. Both fully martensitic and mixed α+α′+β microstructures were confirmed by microscopy. Cooling rates were inferred from the lattice parameter history and complementary thermal simulation. It was found that the threshold cooling rate for fully martensitic transformation is in the range between 2900 and 6500°C/s. IMPACT STATEMENT High-speed synchrotron X-ray diffraction during operando laser processing suggests a new threshold between martensitic and diffusional phase transformation in Ti-6Al-4V occurring at higher cooling rates than previously reported.
- 23 August 2021
- Published by Taylor & Francis in Materials Research Letters
- Vol. 9 (10) , 429-436
Open AccessHigh speed synchrotron X-ray diffraction experiments resolve microstructure and phase transformation in laser processed Ti-6Al-4V
The microstructures of Ti-6Al-4V following laser processing depend primarily on the phase transformation of β to α, but their development is constrained by the rapidly changing temperature in the small fusion zone. In-situ synchrotron X-ray diffraction was utilized to probe the rapid phase evolution in single melt tracks with high angular and temporal resolution. Both fully martensitic and mixed α+α′+β microstructures were confirmed by microscopy. Cooling rates were inferred from the lattice parameter history and complementary thermal simulation. It was found that the threshold cooling rate for fully martensitic transformation is in the range between 2900 and 6500°C/s. IMPACT STATEMENT High-speed synchrotron X-ray diffraction during operando laser processing suggests a new threshold between martensitic and diffusional phase transformation in Ti-6Al-4V occurring at higher cooling rates than previously reported.
- Open Access
- 1 January 2021
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 7 (1) , eabd3614
Exploring microstructures in lower mantle mineral assemblages with synchrotron x-rays
Understanding dynamics across phase transformations and the spatial distribution of minerals in the lower mantle is crucial for a comprehensive model of the evolution of the Earth’s interior. Using the multigrain crystallography technique (MGC) with synchrotron x-rays at pressures of 30 GPa in a laser-heated diamond anvil cell to study the formation of bridgmanite [(Mg,Fe)SiO3] and ferropericlase [(Mg,Fe)O], we report an interconnected network of a smaller grained ferropericlase, a configuration that has been implicated in slab stagnation and plume deflection in the upper part of the lower mantle. Furthermore, we isolated individual crystal orientations with grain-scale resolution, provide estimates on stress evolutions on the grain scale, and report {110} twinning in an iron-depleted bridgmanite, a mechanism that appears to aid stress relaxation during grain growth and likely contributes to the lack of any appreciable seismic anisotropy in the upper portion of the lower mantle.
- 1 January 2021
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 7 (1) , eabd3614
Open AccessExploring microstructures in lower mantle mineral assemblages with synchrotron x-rays
Understanding dynamics across phase transformations and the spatial distribution of minerals in the lower mantle is crucial for a comprehensive model of the evolution of the Earth’s interior. Using the multigrain crystallography technique (MGC) with synchrotron x-rays at pressures of 30 GPa in a laser-heated diamond anvil cell to study the formation of bridgmanite [(Mg,Fe)SiO3] and ferropericlase [(Mg,Fe)O], we report an interconnected network of a smaller grained ferropericlase, a configuration that has been implicated in slab stagnation and plume deflection in the upper part of the lower mantle. Furthermore, we isolated individual crystal orientations with grain-scale resolution, provide estimates on stress evolutions on the grain scale, and report {110} twinning in an iron-depleted bridgmanite, a mechanism that appears to aid stress relaxation during grain growth and likely contributes to the lack of any appreciable seismic anisotropy in the upper portion of the lower mantle.