Aniruddha Konar
Research Subjects
Aniruddha Konar has a total of 146 co-authors. Here are the top co-authors by number of shared publications:
Debdeep Jena
Department of Electrical Engineering, University of Notre Dame , Notre Dame, Indiana 46556, USA
13 shared publicationsTian Fang
University of Notre Dame
13 shared publications- Debdeep Jena
University of Notre Dame
7 shared publications Rajan K. Pandey
GLOBALFOUNDRIES , Bangalore 560045, India
5 shared publicationsHuili Xing
Department of Electrical Engineering, University of Notre Dame , Notre Dame, Indiana 46556, USA
4 shared publicationsK. V. R. M. Murali
4 shared publications
Latest Publications
- 29 March 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (13) , 133504
Surface roughness mediated specularity parameter of thin Cu films
Roughness-induced resistivity variation of thin metal films is conveniently described by the Fuchs–Sondheimer model, where the phenomenological parameter p is used to quantify the extent of specular scattering at surfaces. However, p is a lumped parameter and does not include microscopic information that characterizes roughness, viz., auto-correlation function, root-mean-square height, and correlation length. In this work, we extract these roughness parameters for Cu films of thickness ranging from 31 nm to 95 nm. We find that the roughness–roughness correlation function is an exponential with a characteristic correlation length that increases monotonically with the film thickness. Using this, we predict the roughness parameter-dependent specularity coefficient, which has an implicit thickness dependency. This alters the resistivity scaling compared to the prevailing model of resistivity scaling, where p is assumed to be a constant.
- 29 March 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (13) , 133504
Surface roughness mediated specularity parameter of thin Cu films
Roughness-induced resistivity variation of thin metal films is conveniently described by the Fuchs–Sondheimer model, where the phenomenological parameter p is used to quantify the extent of specular scattering at surfaces. However, p is a lumped parameter and does not include microscopic information that characterizes roughness, viz., auto-correlation function, root-mean-square height, and correlation length. In this work, we extract these roughness parameters for Cu films of thickness ranging from 31 nm to 95 nm. We find that the roughness–roughness correlation function is an exponential with a characteristic correlation length that increases monotonically with the film thickness. Using this, we predict the roughness parameter-dependent specularity coefficient, which has an implicit thickness dependency. This alters the resistivity scaling compared to the prevailing model of resistivity scaling, where p is assumed to be a constant.
- 10 November 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (18) , 185103
Non-specular scattering of carriers from surface defects in thin metal interconnects
Non-specular scattering of carriers, despite being one of the key contributors to metal film resistivity, is conveniently characterized by a single parameter (referred to as specularity parameter) in the literature without providing a means to separate out relative contributions of surface defects to it. In this work, we report a theoretical formalism to predict contributions to (non-specular) reflection (scattering) of carriers from different types of chemical and structural defects on the film surface. Establishing specular reflection as a special case of the more generalized reflection from the surface, we show that elastic scatterings contribute to the non-specular reflections by randomizing the forward momentum along the transport direction. We predict density and angle-dependent specularity coefficient for various types of defects and show that large angle reflections tend to be non-specular in the presence of isotropic surface defects. Using this formalism, we predict the probability of specular reflection for technologically relevant metal–metal and metal–insulator interfaces. Calculated specularity coefficients are in agreement with values obtained from experimental measurements. Our methodology will help in designing next generation interconnects and engineering the interfaces with minimal diffuse reflection.- 10 November 2020
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 128 (18) , 185103
Non-specular scattering of carriers from surface defects in thin metal interconnects
Non-specular scattering of carriers, despite being one of the key contributors to metal film resistivity, is conveniently characterized by a single parameter (referred to as specularity parameter) in the literature without providing a means to separate out relative contributions of surface defects to it. In this work, we report a theoretical formalism to predict contributions to (non-specular) reflection (scattering) of carriers from different types of chemical and structural defects on the film surface. Establishing specular reflection as a special case of the more generalized reflection from the surface, we show that elastic scatterings contribute to the non-specular reflections by randomizing the forward momentum along the transport direction. We predict density and angle-dependent specularity coefficient for various types of defects and show that large angle reflections tend to be non-specular in the presence of isotropic surface defects. Using this formalism, we predict the probability of specular reflection for technologically relevant metal–metal and metal–insulator interfaces. Calculated specularity coefficients are in agreement with values obtained from experimental measurements. Our methodology will help in designing next generation interconnects and engineering the interfaces with minimal diffuse reflection.- 31 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (10) , 4079-4084
Optimized Substrate for Improved Performance of Stacked Nanosheet Field-Effect Transistor
The recently proposed stacked nanosheet-field-effect transistor (SNSH-FET) is considered as a promising candidate for continued scaling with silicon. ,While using punchthrough-stopper-doped (or) ground-plane-doped silicon substrate (PTS-Si substrate) in which the top part of the substrate is doped heavily with the p-type (for nMOS) impurity to avoid punchthrough ,leakage between the source and the drain. The heavily doped p-n junction formed at the drain-substrate junction acts as a reverse-biased ,tunnel diode during VDS biasing, which leads to large substrate leakage current. We presented SuperSteep-Retrograde silicon substrate (SSR-Si substrate) configuration which reduces the tunneling current by increasing the tunnel barrier width and diminishing the peak electric field at the drain-substrate junction. The SSR-Si substrate is achieved by growing a lightly doped or undoped layer of silicon (SSR-buffer layer) on the PTS-doped substrate. The impact of SSR-buffer layer thickness is studied and the optimal thickness (12 nm) is presented. The vertically stacked channels' configuration leads to position-dependent current densities in different channels due to position-dependent series resistance. Herein, we present nanosheet width optimization as a solution to achieve homogeneous current ratio between all the channels thereby resulting in better linearity performance. The self-heating and RF performance of the presented SSR-Si substrate is compared with the silicon-on-insulator (SOI) substrate. The results show that SSR-Si substrate can be a better substrate for SNSH-FET because of better self-heating performance.
- 31 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 67 (10) , 4079-4084
Optimized Substrate for Improved Performance of Stacked Nanosheet Field-Effect Transistor
The recently proposed stacked nanosheet-field-effect transistor (SNSH-FET) is considered as a promising candidate for continued scaling with silicon. ,While using punchthrough-stopper-doped (or) ground-plane-doped silicon substrate (PTS-Si substrate) in which the top part of the substrate is doped heavily with the p-type (for nMOS) impurity to avoid punchthrough ,leakage between the source and the drain. The heavily doped p-n junction formed at the drain-substrate junction acts as a reverse-biased ,tunnel diode during VDS biasing, which leads to large substrate leakage current. We presented SuperSteep-Retrograde silicon substrate (SSR-Si substrate) configuration which reduces the tunneling current by increasing the tunnel barrier width and diminishing the peak electric field at the drain-substrate junction. The SSR-Si substrate is achieved by growing a lightly doped or undoped layer of silicon (SSR-buffer layer) on the PTS-doped substrate. The impact of SSR-buffer layer thickness is studied and the optimal thickness (12 nm) is presented. The vertically stacked channels' configuration leads to position-dependent current densities in different channels due to position-dependent series resistance. Herein, we present nanosheet width optimization as a solution to achieve homogeneous current ratio between all the channels thereby resulting in better linearity performance. The self-heating and RF performance of the presented SSR-Si substrate is compared with the silicon-on-insulator (SOI) substrate. The results show that SSR-Si substrate can be a better substrate for SNSH-FET because of better self-heating performance.
- 1 February 2020
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 115
Improved statistical variability and delay performance with junctionless inserted oxide FinFET
- 1 February 2020
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 115
Improved statistical variability and delay performance with junctionless inserted oxide FinFET
- 1 April 2019
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 93, 188-195
Impact of geometrical parameters and substrate on analog/RF performance of stacked nanosheet field effect transistor
- 1 April 2019
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 93, 188-195
Impact of geometrical parameters and substrate on analog/RF performance of stacked nanosheet field effect transistor
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Materials and Product Technology
- Vol. 59 (4) , 339
Random dopant fluctuations impact reduction in 7 nm bulk-FinFET by substrate engineering
Currently, fin-field-effect-transistors (FinFETs) are used at 7 nm technology node, in order to avoid parasitic leakage channel under the controlled channel punch-through-stopper (PTS) doping is used with the bulk Silicon substrate (PTS-Si substrate). The dopants from PTS doping enters into the channel during the annealing process and increases channel doping level. The increased doping concentration in channel causes undesirable effects such as reduction in channel mobility and increase in random-dopant-fluctuations (RDFs). Using a silicon-on-insulator (SOI) substrate is a costlier solution, this work presents super-steep-retrograde-silicon (SSR-Si) substrate as a better solution for this problem. In this work, the SSR-Si substrate is achieved by placing lightly doped 10 nm thick SSR-buffer layer (silicon) on top of PTS-Si substrate. This SSR-buffer layer captures dopants intruding from PTS doping into channel thereby achieves SSR doping profile in the channel. The results show SSR-Si substrate reduces the RDF induced threshold variations by 50%, it also provides better DC and RF/analogue metrics than PTS-Si substrate and comparable with SOI substrate.
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Materials and Product Technology
- Vol. 59 (4) , 339
Random dopant fluctuations impact reduction in 7 nm bulk-FinFET by substrate engineering
Currently, fin-field-effect-transistors (FinFETs) are used at 7 nm technology node, in order to avoid parasitic leakage channel under the controlled channel punch-through-stopper (PTS) doping is used with the bulk Silicon substrate (PTS-Si substrate). The dopants from PTS doping enters into the channel during the annealing process and increases channel doping level. The increased doping concentration in channel causes undesirable effects such as reduction in channel mobility and increase in random-dopant-fluctuations (RDFs). Using a silicon-on-insulator (SOI) substrate is a costlier solution, this work presents super-steep-retrograde-silicon (SSR-Si) substrate as a better solution for this problem. In this work, the SSR-Si substrate is achieved by placing lightly doped 10 nm thick SSR-buffer layer (silicon) on top of PTS-Si substrate. This SSR-buffer layer captures dopants intruding from PTS doping into channel thereby achieves SSR doping profile in the channel. The results show SSR-Si substrate reduces the RDF induced threshold variations by 50%, it also provides better DC and RF/analogue metrics than PTS-Si substrate and comparable with SOI substrate.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-88
Leakage aware Si/SiGe CMOS FinFET for low power applications
Leakage in Si/SiGe CMOS FinFET is examined. Si cap passivation effectively improves SiGe pFET Dit, subthreshold slope, and mobility, which improves pFET DC performance by 20%. SiGe GIDL is higher than Si by a factor of 9, though GIDL is limited to 50pA/um. SiGe GIDL reduction knobs to meet Si counterpart are demonstrated. The results open the door to the next stage of Si/SiGe CMOS FinFET such as low power and low leakage applications.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-88
Leakage aware Si/SiGe CMOS FinFET for low power applications
Leakage in Si/SiGe CMOS FinFET is examined. Si cap passivation effectively improves SiGe pFET Dit, subthreshold slope, and mobility, which improves pFET DC performance by 20%. SiGe GIDL is higher than Si by a factor of 9, though GIDL is limited to 50pA/um. SiGe GIDL reduction knobs to meet Si counterpart are demonstrated. The results open the door to the next stage of Si/SiGe CMOS FinFET such as low power and low leakage applications.
- 20 October 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (45) , 455103
How thin barrier metal can be used to prevent Co diffusion in the modern integrated circuits?
In modern integrated circuits (ICs), billions of transistors are connected to each other via thin metal layers (e.g. copper, cobalt, etc) known as interconnects. At elevated process temperatures, inter-diffusion of atomic species can occur among these metal layers, causing sub-optimal performance of interconnects, which may lead to the failure of an IC. Thus, typically a thin barrier metal layer is used to prevent the inter-diffusion of atomic species within interconnects. For ICs with sub-10 nm transistors (10 nm technology node), the design rule (thickness scaling) demands the thinnest possible barrier layer. Therefore, here we investigate the critical thickness of a titanium–nitride (TiN) barrier that can prevent the cobalt diffusion using multi-scale modeling and simulations. First, we compute the Co diffusion barrier in crystalline and amorphous TiN with the nudged elastic band method within first-principles density functional theory simulations. Later, using the calculated activation energy barriers, we quantify the Co diffusion length in the TiN metal layer with the help of kinetic Monte Carlo simulations. Such a multi-scale modelling approach yields an exact critical thickness of the metal layer sufficient to prevent the Co diffusion in IC interconnects. We obtain a diffusion length of a maximum of 2 nm for a typical process of thermal annealing at 400 °C for 30 min. Our study thus provides useful physical insights for the Co diffusion in the TiN layer and further quantifies the critical thickness (~2 nm) to which the metal barrier layer can be thinned down for sub-10 nm ICs.
- 20 October 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (45) , 455103
How thin barrier metal can be used to prevent Co diffusion in the modern integrated circuits?
In modern integrated circuits (ICs), billions of transistors are connected to each other via thin metal layers (e.g. copper, cobalt, etc) known as interconnects. At elevated process temperatures, inter-diffusion of atomic species can occur among these metal layers, causing sub-optimal performance of interconnects, which may lead to the failure of an IC. Thus, typically a thin barrier metal layer is used to prevent the inter-diffusion of atomic species within interconnects. For ICs with sub-10 nm transistors (10 nm technology node), the design rule (thickness scaling) demands the thinnest possible barrier layer. Therefore, here we investigate the critical thickness of a titanium–nitride (TiN) barrier that can prevent the cobalt diffusion using multi-scale modeling and simulations. First, we compute the Co diffusion barrier in crystalline and amorphous TiN with the nudged elastic band method within first-principles density functional theory simulations. Later, using the calculated activation energy barriers, we quantify the Co diffusion length in the TiN metal layer with the help of kinetic Monte Carlo simulations. Such a multi-scale modelling approach yields an exact critical thickness of the metal layer sufficient to prevent the Co diffusion in IC interconnects. We obtain a diffusion length of a maximum of 2 nm for a typical process of thermal annealing at 400 °C for 30 min. Our study thus provides useful physical insights for the Co diffusion in the TiN layer and further quantifies the critical thickness (~2 nm) to which the metal barrier layer can be thinned down for sub-10 nm ICs.
- 18 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (15)
Carrier transport in layered nanolaminated carbides
This paper summarizes the ab-initio electronic and phonon band structures and the temperature-dependent carrier transport in layered Ti2AlC. It is found that the cylindrical Fermi surface is the origin of the anisotropic carrier effective mass (infinite effective mass along the c axis), which leads to a strong anisotropic (insulator along the c axis and metallic along the layer) carrier transport in these films. Using electronic and phonon band structure calculations, we have developed an analytical model for the carrier-phonon interaction and the in-plane carrier conductivity originating from the strong inter-valley (s → d) scattering in Ti2AlC. The density functional theory is used to calculate the average deformation potential corresponding to the acoustic phonon vibrations. The calculated deformation potential is in good agreement with the extracted deformation potential from the transport data available in the literature. The extracted deformation potential will be useful for predicting the transport quantities of these metals at elevated temperatures.
- 18 October 2017
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 122 (15)
Carrier transport in layered nanolaminated carbides
This paper summarizes the ab-initio electronic and phonon band structures and the temperature-dependent carrier transport in layered Ti2AlC. It is found that the cylindrical Fermi surface is the origin of the anisotropic carrier effective mass (infinite effective mass along the c axis), which leads to a strong anisotropic (insulator along the c axis and metallic along the layer) carrier transport in these films. Using electronic and phonon band structure calculations, we have developed an analytical model for the carrier-phonon interaction and the in-plane carrier conductivity originating from the strong inter-valley (s → d) scattering in Ti2AlC. The density functional theory is used to calculate the average deformation potential corresponding to the acoustic phonon vibrations. The calculated deformation potential is in good agreement with the extracted deformation potential from the transport data available in the literature. The extracted deformation potential will be useful for predicting the transport quantities of these metals at elevated temperatures.