SSSmitha Venu Sreekala

Smitha Venu Sreekala

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Smitha Venu Sreekala has a total of 27 co-authors. Here are the top co-authors by number of shared publications:

  • Resmi Thoppil Ramakrishnan

    Ecology and Environment Research Group, Centre for Water Resources Development and Management, Kunnamangalam P.O, Calicut, India

    5 shared publications
  • Balagopal N. Nair

    Materials Science and Technology Division, National Institute for Interdisciplinary Science and Technology, Industrial Estate P.O., Thiruvananthapuram695019, Kerala, India

    4 shared publications
  • Harikumar Puthenveedu Sadasivan Pillai

    Ecology and Environment Research Group, Centre for Water Resources Development and Management, Kunnamangalam P.O., Calicut, India

    4 shared publications
  • Athulya Parola

    Ecology and Environment Research Group, Centre for Water Resources Development and Management, Kunnamangalam P.O, Calicut, India

    3 shared publications
  • Unnikrishnan Nair Saraswathy Hareesh

    Chemical Sciences and Technology Division CSIR‐National Institute for Interdisciplinary Science and Technology (CSIR‐NIIST) Thiruvananthapuram India

    3 shared publications
  • Jayasooryan Kazhuthuttil Kochu

    Ecology and Environment Research Group, Centre for Water Resources Development and Management, Kunnamangalam P.O, Calicut, India

    2 shared publications

Latest Publications

  • Modified bentonite loaded with nonmetal doped titanium dioxide for the removal of heavy metal ions and dyes from wastewater

    by Smitha Venu Sreekala, Anu Sreeja Pramod, Athulya Parola, Jayasooryan Kazhuthuttil Kochu, Resmi Thoppil Ramakrishnan


  • Antifouling behavior of titania–silica-reduced graphene oxide nanocomposites as coatings for marine applications

    by Venu Sreekala Smitha, Anson Swargy, Malayil Digilarani, Thayumani Vimala, Thoppil Ramakrishnan Resmi

    Fouling, the unwanted accumulation of marine organisms and debris on submerged surfaces, is a pervasive problem in marine environments as it can have significant economic, environmental, and ecological consequences impacting marine industries. The present work offers a facile, low cost and eco-friendly method for developing antifouling coatings suitable for marine applications. A novel coating formulation based on reduced graphene oxide incorporated titania–silica nanocomposite (TS-RGO) was synthesized successfully using a sol–gel method. The structural, morphological, and functional features of the synthesized nanocomposites were evaluated using different characterization studies such as X-ray diffraction analysis, UV-visible spectral analysis, Fourier transform infrared spectral analysis, Raman analysis, BET surface area analysis, and scanning electron microscopy analysis. The functional nanocomposites were made into coatings of different compositions and their antifouling properties against E. coli, marine bacteria, marine algae, and freshwater algae were investigated in detail. Antifouling studies performed with freshwater and marine organisms show that the developed TS-RGO nanocomposite and its coating possess good antifouling properties. It was observed that the algal/bacterial colonies on the TS-RGO coated substrates were significantly less numerous than those on the uncoated substrates from the field experiments conducted at the Beypore Port, Calicut, Kerala. Swelling and degradation studies performed on the nanocomposite coatings in the presence of artificial seawater revealed the stability and durability of the functional coatings. Thus, the results obtained in the present work indicated the suitability of the synthesized graphene oxide incorporated titania–silica nanocomposites as antifouling agents for marine applications.


  • Novel ternary nanocomposite (TiO2@Fe3O4-chitosan) system for nitrate removal from water: an adsorption cum photocatalytic approach

    by Smitha Venu Sreekala, Jilsha George, Resmi Thoppil Ramakrishnan, Harikumar Puthenveedu Sadasivan Pillai

    Nitrate pollution of water emerging from various anthropogenic activities has become a major environmental concern because of its deleterious effects on natural water resources. The present work deals with the synthesis of the ternary nanocomposite based on chitosan, iron oxide (Fe3O4), and titanium dioxide (TiO2) and its application for the removal of nitrates from model-contaminated water. Fe3O4 derived through a coprecipitation method was incorporated into the chitosan matrix which was fabricated in the form of beads. The wet gel beads were then successfully coated with sol–gel-derived silver-doped titanium dioxide sol followed by drying under suitable conditions to get the functional nanocomposite beads. The synthesized functional materials were further characterized for their structural, morphological, and textural features using X-ray diffraction analysis, physical property measurement (PPMS), Fourier transform infrared (FTIR) analysis, UV visible spectroscopy analysis (UV–vis), BET surface area analysis (BET), field emission scanning electron microscopic (FESEM), and transmission electron microscopy (TEM) analysis. The ternary nanocomposites were further used for the removal of nitrates via adsorption cum photocatalytic reduction technique from the model contaminated water when subjected to an adsorption study under dark conditions and photocatalytic study under UV/visible/sunlight for a definite time. Fe3O4 in the nanocomposite provides enhanced adsorption features whereas the functional coating of titanium dioxide aids in the removal of nitrates through the photocatalytic reduction technique. The functional beads containing 3% Fe3O4 in the wet gel form (CTA-F3) have excellent nitrate removal efficiency of ~ 97% via adsorption cum solar photocatalysis towards the removal of nitrate ions from 50 ppm nitrate solution, whereas the dried nanocomposite beads have got a nitrate removal efficiency of ~ 68% in 1 h from 100 ppm nitrate solution. Continuous flow adsorption cum photocatalytic study was performed further using the oven-dried functional beads in which flow rate and bed height were varied while maintaining the concentration of feed solution as constant. A nitrate removal efficiency of 65% and an adsorption capacity of 4.1 mgg−1 were obtained for the CTA-F3 beads in the continuous flow adsorption cum photocatalysis experiment for up to 5 h when using an inlet concentration of 100 ppm, bed height 12 cm, and flow rate 5.0 ml min−1. A representative fixed-bed column adsorption experiment conducted using CTA-F3 beads for the treatment of a real groundwater sample shows reasonable results for nitrate removal (71.7% efficiency) along with a significant removal rate for the other anions as well. Thus, the novel adsorbent/photocatalyst developed is suitable for the removal of nitrates from water due to the synergistic effect between Fe3O4, chitosan, and titanium dioxide.


  • Open Access

    Fluorescent carbon dot embedded silica nanocomposites as tracers for hydrogeological investigations: a sustainable approach

    by Venu Sreekala Smitha, Parola Athulya, Kazhuthoottil Kochu Jayasooryan, Thoppil Ramakrishnan Resmi

    The injected tracer technique using nanoparticles has evoked a lot of research interest in hydrogeological research as it encompasses a broad spectrum of applications in water resource management.


  • Efficient nitrate reduction in water using an integrated photocatalyst adsorbent based on chitosan-titanium dioxide nanocomposite

    by Smitha Venu Sreekala, Athulya Parola, Vimala Thayumani, Harikumar Puthenveedu Sadasivan Pillai, Resmi Thoppil Ramakrishnan

    Globally, there exists a huge concern on the increased discharge of nitrates to the natural water resources out of various anthropogenic activities as it causes serious environmental pollution and associated harmful effects. In the present work, sol–gel-derived functional nanocomposites based on silver (Ag) and nitrogen (N)-doped titanium dioxide (TiO2)-coated chitosan nanocomposites were successfully synthesized in the form of beads, and their application for the reduction of nitrates in water was studied. The synthesized nanocomposite beads were characterized for their structural, textural, and morphological features using X-ray diffraction analysis, Fourier transform infrared spectroscopy, UV–visible spectroscopy, BET surface area analysis, Scanning electron microscopy, Transmission electron microscopy, and X-ray photoelectron spectroscopy. A uniform coating of doped titania species on the chitosan porous structure was achieved through electrostatic interaction. Adsorption/photocatalytic reduction of nitrates was further carried out using functional nanocomposite beads by monitoring the nitrate concentration of the model contaminated water, in an adsorption study under dark condition and photocatalytic study under UV/sunlight for a definite time period. Drying conditions of the nanocomposite beads were found to have a significant effect on the adsorption cum photocatalytic efficiencies of the nanocomposite. The freeze-dried chitosan-titania nanocomposite beads containing 0.5 mol% Ag exhibited an adsorption efficiency of ~ 43.5% (under dark for 30 min) and photocatalytic reduction capability of ~ 95% (under sunlight for 2 h), whereas the oven dried beads of the same composition exhibits adsorption and photocatalytic efficiencies of 40% (under dark for 30 min) and 70% (under UV light for 2 h) respectively, towards the reduction of nitrate ions in an aqueous solution. Continuous flow adsorption cum photocatalytic study using the oven-dried nanocomposite beads was also carried out with the help of an experimental setup fabricated in-house and under varying experimental conditions such as flow rate, bed height, and concentration of feed solution. Nitrate reduction efficiency of 87.6% and an adsorption capacity of 7.9 mg g−1 were obtained for the nanocomposite beads in the continuous flow adsorption cum photocatalysis experiment for up to 8 h when using an inlet concentration of 100 ppm, bed height 12 cm, and flow rate 5.0 mL min−1. A representative fixed-bed column adsorption experiment performed with oven dried nanocomposite beads in a real groundwater sample collected from the Palakkad District of Kerala shows promising results for nitrate reduction (85.9% efficiency) along with a significant removal rate for the other anions as well. Thus, the adsorption cum photocatalytic nitrate reduction efficiency of the functional nanocomposite material makes them suitable for the reduction of nitrates from water/wastewater through an integrated nanocomposite approach. Graphical Abstract


  • Open Access

    Efficient nitrate removal from water using an integrated photocatalyst-adsorbent based on chitosan-titanium dioxide nanocomposite

    by Smitha Venu Sreek, Athulya Parola, Vimala Thaimani, Harikumar Puthenveedu Sadasivan Pillai, Resmi Thoppil Ramakrishnan

    An increased discharge of nitrates to the natural water resources was observed across the globe due to various anthropogenic activities resulting in environmental pollution and associated harmful effects. In the present work, sol-gel-derived functional nanocomposites based on silver (Ag) doped titanium dioxide (TiO2) coated chitosan nanocomposites were successfully synthesized in the form of beads and their application for the removal of nitrates from the water was studied. The synthesized nanocomposite beads were further characterized for their structural, textural, and morphological features using X-ray Diffraction Analysis, Fourier Transform Infrared Spectroscopy, UV-Visible Spectroscopy, BET Surface Area analysis, Scanning Electron Microscopy, and Transmission Electron Microscopy. A uniform coating of doped titania species on the chitosan porous structure was achieved through electrostatic interaction. Adsorption/ photocatalytic reduction of nitrates was further monitored by measuring the concentration of nitrate ions in the model contaminated water in the presence of functional nanocomposite beads when subjected to an adsorption study under dark conditions and photocatalytic study under UV/sunlight for a definite time. Drying conditions of the nanocomposite beads were found to have a significant effect on the adsorption cum photocatalysis efficiencies of the nanocomposite. The freeze-dried chitosan-titania nanocomposite beads containing 0.5 mol% Ag exhibited an adsorption efficiency of ~ 43.5% (under dark for 30 min) and photocatalytic reduction capability of ~ 95% (under sunlight for 2 hours), whereas the adsorption and photocatalytic efficiencies were 40% (under dark for 30 min) and 70% (under UV light for 2 hours) respectively, in the case of oven-dried nanocomposite beads, towards the removal of nitrate ions in an aqueous solution. Continuous flow adsorption cum photocatalytic study using the oven-dried nanocomposite beads was carried out further with the help of an experimental setup fabricated in-house and under varying experimental conditions such as flow rate, bed height, and concentration of feed solution. A nitrate removal efficiency of 87.6% and an adsorption capacity of 7.9 mgg− 1were obtained for the nanocomposite beads in the continuous flow adsorption cum photocatalysis experiment for up to 8 hours when using an inlet concentration of 100 ppm, bed height 12 cm and flow rate 5.0 mlmin− 1. A representative fixed-bed column adsorption experiment using a real groundwater sample collected from the Palakkad District of Kerala was also performed using the oven-dried functional nanocomposite beads that show promising results for nitrate removal (85.9% efficiency) along with a significant removal rate for the other anions as well. Thus, the adsorption cum photocatalytic nitrate reduction ability of the synthesized functional material makes them suitable for the efficient removal of nitrates from water/wastewater through an integrated nanocomposite approach.


  • Bentonite-titanium dioxide functional nanocomposites suitable for wastewater treatment: an integrated photocatalyst-adsorbent system

    by Smitha Venu Sreekala, Athira Vayalveettil, Jayasooryan Kazhuthuttil Kochu, Resmi Thoppil Ramakrishnan, Harikumar Puthenveedu Sadasivan Pillai

    An integrated photocatalytic adsorbent system prepared from bentonite clay and titanium dioxide was used for the adsorption/degradation of model organic pollutants and adsorption of heavy metals from industrial wastewater. The functional nanocomposite system containing the photocatalyst and the adsorbent was synthesized via a sol–gel method followed by determining the physicochemical and morphological characteristics using XRD analysis, FTIR analysis, thermal analysis, SEM analysis, and nitrogen sorption analysis. The results obtained confirmed the successful formation of bentonite-titania nanocomposites. The effect of various parameters influencing the functional features of the developed material such as catalyst concentration, pH/temperature of the reaction, etc. was systematically investigated. The enhanced photocatalytic/adsorptive removal efficiencies of the synthesized nanocomposites are attributed to the smaller particle size (∼30–40 nm) and high surface area of the titania particles which enhanced the number of surface-active sites responsible for the degradation of model organic pollutants within a reasonable time. Moreover, the functional nanocomposite was suitable for the removal of heavy metals from model water/industrial wastewater due to its adsorption characteristics. Thus, the methodology adopted in the present work for the synthesis of low cost, recyclable bentonite-titania nanocomposites is a facile and eco-friendly method for wastewater treatment due to the synergistic effect of photocatalysis and adsorption.


  • Lanthanum Phosphate-Incorporated Organosilane Nanocomposites for Gas-Phase CO2 Detection

    by Smitha Venu Sreekala, Visakh Vijayan, Peer Mohamed Abdul Azeez, Balagopal N. Nair, Unnikrishnan Nair Saraswathy Hareesh


  • ORMOSIL–ZrO 2 hybrid nanocomposites and coatings on aluminium alloys for corrosion resistance; a sol–gel approach

    by V. S. Smitha, S. S. Syamili, A. Peer Mohamed, Balagopal N. Nair, U. S. Hareesh

    Sol–gel derived ORMOSIL–ZrO 2 hybrid nanocomposites as protective environment-resistant functional coatings on glass substrates and aluminium alloys.


  • Transparent and Hydrophobic MTMS/GPTMS Hybrid Aerogel Monoliths and Coatings by Sol‐Gel Method: A Viable Remedy for Oil‐Spill Cleanup

    by Venu Sreekala Smitha, Peer Mohamed Abdul Azeez, Krishna Gopakumar Warrier, Balagopal N. Nair, Unnikrishnan Nair Saraswathy Hareesh

    Sol‐gel derived hybrid aerogel monoliths and coatings of methyltrimethoxysilane (MTMS) and glycidoxypropyltrimethoxysilane (GPTMS) are prepared sucessfully. MTMS/GPTMS is hydrolyzed under acidic conditions and further condensed under basic conditions to generate a gel network followed by a sequential solvent exchange process and ambient drying to obtain aerogel monoliths. The as‐synthesized alcogel is homogenized in methanol and coatings are fabricated on glass substrates by dip coating method followed by controlled thermal treatment at 400 °C to get organically modified silica (ORMOSIL) based aerogel coatings. The transparent ORMOSIL aerogel coating made from the composition of MTMS/GPTMS ratio 1: 0.5 is found to be highly porous with an average pore size of ∼100 nm and hydrophobic coatings with water contact angle of ∼100 ° are obtained. The hybrid aerogel has ∼334 m 2 g −1 surface area (BET) with an average pore diameter of ∼2.7 nm, and the coating retains its hydrophobicity even after thermal treatment at 400 °C. Hybrid aerogel coatings were also made on cotton canvas fabrics which demonstrate oil adsorption‐desorption properties and is a viable remedy for oil‐spill cleanup.