Sophie Maricot
Research Subjects
Sophie Maricot has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
- Jean Pierre Vilcot
Institute of Electronics, Microelectronics and Nanotechnology (IEMN), UMR CNRS 8520, University of Sciences and Technologies of Lille, 1 Avenue Poincare, 60069, 59652 Villeneuve of Ascq, France
20 shared publications D. Decoster
8 shared publicationsB. Pinchemel
Laboratoire de Physique des Lasers, Atomes et Molécules
3 shared publicationsD. Rondi
3 shared publicationsJ.C. Renaud
3 shared publicationsM. Bouazaoui
Laboratoire de Physique des Lasers, Atomes et Molécules
3 shared publications
Latest Publications
- Open Access
Plasmonic Layer as a Localized Temperature Control Element for Surface Plasmonic Resonance-Based Sensors
Surface plasmon resonance (SPR) sensing is a well-established high-sensitivity, label-free and real-time detection technique for biomolecular interaction study. Its primary working principle consists of the measurement of the optical refractive index of the medium that is in close vicinity of the sensor surface. Bio-functionalization techniques allow biomolecular events to be located in such a way. Since optical refractive indices of any medium varies with the temperature, the place where the measurement takes place shall be within a temperature-controlled environment in order to ensure any temperature fluctuation is interpreted as a biomolecular event. Since the SPR measurement probes the sensed medium within the penetration depth of the plasmonic wave, which is less or in the order of 1 µm, we propose to use the metallic film constituting the detection surface as a localized heater aiming at controlling finely and quickly the temperature of the sensed medium. The Joule heating principle is then used and the modeling of the heater is reported as well as its validation by thermal IR imaging. Using water as a demonstration medium, SPR measurement results at different temperatures are successfully compared to the theoretical optical refractive index of water versus temperature.
Open AccessPlasmonic Layer as a Localized Temperature Control Element for Surface Plasmonic Resonance-Based Sensors
Surface plasmon resonance (SPR) sensing is a well-established high-sensitivity, label-free and real-time detection technique for biomolecular interaction study. Its primary working principle consists of the measurement of the optical refractive index of the medium that is in close vicinity of the sensor surface. Bio-functionalization techniques allow biomolecular events to be located in such a way. Since optical refractive indices of any medium varies with the temperature, the place where the measurement takes place shall be within a temperature-controlled environment in order to ensure any temperature fluctuation is interpreted as a biomolecular event. Since the SPR measurement probes the sensed medium within the penetration depth of the plasmonic wave, which is less or in the order of 1 µm, we propose to use the metallic film constituting the detection surface as a localized heater aiming at controlling finely and quickly the temperature of the sensed medium. The Joule heating principle is then used and the modeling of the heater is reported as well as its validation by thermal IR imaging. Using water as a demonstration medium, SPR measurement results at different temperatures are successfully compared to the theoretical optical refractive index of water versus temperature.
- Open Access
- 6 October 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (12) , 125003
Leak-free integrated microfluidic channel fabrication for surface plasmon resonance applications
In this paper, we describe a novel fabrication method of a microfluidic integrated surface plasmon resonance (SPR) gold chip based on a (3-mercaptopropyl) trimethoxy silane (MPTMS) self-assembled monolayer. This monolayer was formed at the surface of a microfluidic chip made of polydimethylsiloxane (PDMS). Its presence was confirmed by contact angle and Fourier transform infrared spectroscopy measurements on the modified PDMS surface. A basic, but nevertheless appropriate, 4-channel microfluidic system was made on PDMS and reported on a gold SPR sensor. Sealing tests were carried-out by injecting continuous flows of solutions under gradient pressure up to 1.8 bar. Bonding strength of chemical and corona binding were measured and compared. The test of the integrated microfluidic SPR sensor on an SPR bench validated its functionality and proved as well that no leakage is observed between the different microfluidic channels.
- 6 October 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (12) , 125003
Open AccessLeak-free integrated microfluidic channel fabrication for surface plasmon resonance applications
In this paper, we describe a novel fabrication method of a microfluidic integrated surface plasmon resonance (SPR) gold chip based on a (3-mercaptopropyl) trimethoxy silane (MPTMS) self-assembled monolayer. This monolayer was formed at the surface of a microfluidic chip made of polydimethylsiloxane (PDMS). Its presence was confirmed by contact angle and Fourier transform infrared spectroscopy measurements on the modified PDMS surface. A basic, but nevertheless appropriate, 4-channel microfluidic system was made on PDMS and reported on a gold SPR sensor. Sealing tests were carried-out by injecting continuous flows of solutions under gradient pressure up to 1.8 bar. Bonding strength of chemical and corona binding were measured and compared. The test of the integrated microfluidic SPR sensor on an SPR bench validated its functionality and proved as well that no leakage is observed between the different microfluidic channels.
- 9 March 2013
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 1203-1208
Substrate Mode-Integrated SPR Sensor
- 9 March 2013
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 1203-1208
Substrate Mode-Integrated SPR Sensor
- 18 September 2012
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 619-624
Comparison of Gold and Silver/Gold Bimetallic Surface for Highly Sensitive Near-infrared SPR Sensor at 1550 nm
- 18 September 2012
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 619-624
Comparison of Gold and Silver/Gold Bimetallic Surface for Highly Sensitive Near-infrared SPR Sensor at 1550 nm
- 30 April 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8424, 84240
Integrated prism-free coupled surface plasmon resonance biochemical sensor
We present the design, implementation and characterization of an integrated surface plasmon resonance biosensor chip involving diffractive optical coupling elements avoiding the need of prism coupling. The integrated sensor chip uses the angular interrogation principle and includes two diffraction gratings and the SPR sensing zone. The theoretical design is presented as well as the fabrication procedure. Experimental results, using reference index fluids, are compared to theoretical predictions and prism coupling experimental results. We believe that this architecture is perfectly suitable for low cost and reproducible SPR biochemical sensor chips since the sensing zone can be functionalized as any other one.© (2012) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- 30 April 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8424, 84240
Integrated prism-free coupled surface plasmon resonance biochemical sensor
We present the design, implementation and characterization of an integrated surface plasmon resonance biosensor chip involving diffractive optical coupling elements avoiding the need of prism coupling. The integrated sensor chip uses the angular interrogation principle and includes two diffraction gratings and the SPR sensing zone. The theoretical design is presented as well as the fabrication procedure. Experimental results, using reference index fluids, are compared to theoretical predictions and prism coupling experimental results. We believe that this architecture is perfectly suitable for low cost and reproducible SPR biochemical sensor chips since the sensing zone can be functionalized as any other one.© (2012) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is permitted for personal use only.
- 1 October 2011
- Published by Elsevier in Current Opinion in Solid State and Materials Science
- Vol. 15 (5) , 208-224
Surface plasmon resonance-based biosensors: From the development of different SPR structures to novel surface functionalization strategies
- 1 October 2011
- Published by Elsevier in Current Opinion in Solid State and Materials Science
- Vol. 15 (5) , 208-224
Surface plasmon resonance-based biosensors: From the development of different SPR structures to novel surface functionalization strategies
- 19 June 2009
- Published by Optica Publishing Group in Optics Letters
- Vol. 34 (13) , 1936-1938
Ultracompact optical filter based on a stub resonator in GaInAsP/InP optical wire technology
We report on the fabrication and characterization of a very compact filtering structure based on a resonant stub fabricated using optical wire technology in the InP material line. The stub length is close to and has been designed to get a resonance wavelength close to . The characterization showed a resonance frequency at with a resonance peak.- 19 June 2009
- Published by Optica Publishing Group in Optics Letters
- Vol. 34 (13) , 1936-1938
Ultracompact optical filter based on a stub resonator in GaInAsP/InP optical wire technology
We report on the fabrication and characterization of a very compact filtering structure based on a resonant stub fabricated using optical wire technology in the InP material line. The stub length is close to and has been designed to get a resonance wavelength close to . The characterization showed a resonance frequency at with a resonance peak.- 24 June 2008
- Published by Optica Publishing Group in Optics Letters
- Vol. 33 (13) , 1467-1469
Wide electrical tunability of a GaInAsP/InP microdisk resonator
We report on the characterization of an -material-based microdisk resonator optical filter. The originality here is constituted by the use of a localized control electrode that is used for the tuning of the resonance wavelength of the filter via the injection of a driving current. Tuning of the resonance wavelength close to has been experimentally achieved for a drive current of .- 24 June 2008
- Published by Optica Publishing Group in Optics Letters
- Vol. 33 (13) , 1467-1469
Wide electrical tunability of a GaInAsP/InP microdisk resonator
We report on the characterization of an -material-based microdisk resonator optical filter. The originality here is constituted by the use of a localized control electrode that is used for the tuning of the resonance wavelength of the filter via the injection of a driving current. Tuning of the resonance wavelength close to has been experimentally achieved for a drive current of .- 7 April 2008
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 2 (2) , 69-75
Passive photonic components using InP optical wire technology
The authors present the design, fabrication and characterisation of passive photonic components using InP optical wire technology. These components are straight and curved waveguides as well as Y-junctions. Their ultimate use is to be integrated within active nanophotonic functions and this is implicitly targeted in the different parts of this process work. First, propagation and excess losses because of a bend or Y-junction are modelled using a beam propagation method or a finite difference time domain method. Then, the technological process used to fabricate these components is presented; it is mainly based on e-beam direct writing and inductively coupled plasma deep etching. Finally, the different losses are measured and results are compared with the theory. The authors demonstrate, thus, that the use of submicron waveguides (or optical wire) can lead to very compact optical passive functions on InP since very small radius bends and wide angle Y-junctions showed almost low excess loss.
- 7 April 2008
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 2 (2) , 69-75
Passive photonic components using InP optical wire technology
The authors present the design, fabrication and characterisation of passive photonic components using InP optical wire technology. These components are straight and curved waveguides as well as Y-junctions. Their ultimate use is to be integrated within active nanophotonic functions and this is implicitly targeted in the different parts of this process work. First, propagation and excess losses because of a bend or Y-junction are modelled using a beam propagation method or a finite difference time domain method. Then, the technological process used to fabricate these components is presented; it is mainly based on e-beam direct writing and inductively coupled plasma deep etching. Finally, the different losses are measured and results are compared with the theory. The authors demonstrate, thus, that the use of submicron waveguides (or optical wire) can lead to very compact optical passive functions on InP since very small radius bends and wide angle Y-junctions showed almost low excess loss.