Hangzhi Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Hangzhi Liu has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jun Wang
Hunan University
6 shared publications - Shiwei Liang
Hunan University
6 shared publications - Hengyu Yu
Department of Electrical & Computer Engineering, The Ohio State University, Columbus, OH 43210, USA
5 shared publications - Yuming Zhou
Anhui Provincial Key Laboratory for Power Electronics and Motion Control, Anhui University of Technology, Maanshan, China
4 shared publications - Gaoqiang Deng
Engineering Research Center of Advanced Power and RF Devices and Integration, Ministry of Education, University of Electronic Science and Technology of China, Chengdu, China
3 shared publications - Zheng John Shen
Simon Fraser University
3 shared publications
Latest Publications
- Open Access
- 1 March 2026
- Published by KEAI Publishing in Journal of Electronic Science and Technology
- Vol. 24 (1)
Comprehensive evaluation on Si/SiC hybrid switch including single-pulse avalanche and short-circuit robustness
- 1 March 2026
- Published by KEAI Publishing in Journal of Electronic Science and Technology
- Vol. 24 (1)
Open AccessComprehensive evaluation on Si/SiC hybrid switch including single-pulse avalanche and short-circuit robustness
- 3 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1023-1034
A Novel Full-Bridge Boost LCL-Type DC/DC Converter With a Constant Off-Time: Analysis, Design, and Experimental Results
This article presents a full-bridge boost LCL -type dc/ac/dc converter with an isolation transformer. In the proposed converter, the output voltage is regulated by controlling frequency with a constant turn- off time of the switches. Traditional capacitor works under resonant function so that the dc-bus capacitor is eliminated. Under this design, the converter works under zero voltage switching condition in the entire operation range without auxiliary circuits. To minimize the energy dissipation, the waveform of the tank voltage has been modulated. A Fourier's mathematical description is exploited to help the design, and detailed power simulation (PSIM) results are presented to verify the performance of the designed converter at varied input voltage. Additionally, a laboratory prototype converter with 50−162 V input and 200-V/400-W output is built to confirm the proposed design. The experimental results show that the converter has a wider input-voltage range with a narrow switching frequency range.
- 3 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1023-1034
A Novel Full-Bridge Boost LCL-Type DC/DC Converter With a Constant Off-Time: Analysis, Design, and Experimental Results
This article presents a full-bridge boost LCL -type dc/ac/dc converter with an isolation transformer. In the proposed converter, the output voltage is regulated by controlling frequency with a constant turn- off time of the switches. Traditional capacitor works under resonant function so that the dc-bus capacitor is eliminated. Under this design, the converter works under zero voltage switching condition in the entire operation range without auxiliary circuits. To minimize the energy dissipation, the waveform of the tank voltage has been modulated. A Fourier's mathematical description is exploited to help the design, and detailed power simulation (PSIM) results are presented to verify the performance of the designed converter at varied input voltage. Additionally, a laboratory prototype converter with 50−162 V input and 200-V/400-W output is built to confirm the proposed design. The experimental results show that the converter has a wider input-voltage range with a narrow switching frequency range.
- Open Access
- 8 May 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (7) , 878-889
Physical insight into turn‐on transient of silicon carbide gate turn‐off thyristor
Silicon Carbide (SiC) Gate Turn‐off (GTO) thyristor is regarded as a promising option for pulsed power applications; however, the formation of high di/dt has been constrained by the slow current rise transient phase and the turn‐on current heterogeneity over the chip device. In this paper, a practical integrated multi‐cell simulation is performed to physically characterize the turn‐on transient of SiC GTO thyristor. Through examining electrical coupling between adjacent cells caused by both parasitics of electrode metallization and carrier travelling via SiC, the current distributions are observed, and the carrier transport dynamics are analyzed in detail. Furthermore, physical mechanisms dominating the current heterogeneity among multi‐cells are discovered in depth. It is revealed that the current heterogeneity during the turn‐on transient is primarily resulted from the Gate signal delay caused by the Gate Runner metallization, and the lateral interaction from adjacent semiconductor regions adds to this inhomogeneity; however, this situation can be improved once the electrical distance between each Anode contact and the Anode electrode gets lowered. Design method for turn‐on performance improvement is also proposed accordingly. Besides, based on the analysis conducted on the multi‐cell simulation results, the possible reason of the extremely slow current rise transient phase is speculated and experimentally verified. The improvement in the comprehension of SiC GTO's turn‐on transient, which cannot be obtained from the traditional investigation from the viewpoint of one elementary cell, will provide guiding principles helping in directing future efforts to advance the improvement of device design technology.
- 8 May 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (7) , 878-889
Open AccessPhysical insight into turn‐on transient of silicon carbide gate turn‐off thyristor
Silicon Carbide (SiC) Gate Turn‐off (GTO) thyristor is regarded as a promising option for pulsed power applications; however, the formation of high di/dt has been constrained by the slow current rise transient phase and the turn‐on current heterogeneity over the chip device. In this paper, a practical integrated multi‐cell simulation is performed to physically characterize the turn‐on transient of SiC GTO thyristor. Through examining electrical coupling between adjacent cells caused by both parasitics of electrode metallization and carrier travelling via SiC, the current distributions are observed, and the carrier transport dynamics are analyzed in detail. Furthermore, physical mechanisms dominating the current heterogeneity among multi‐cells are discovered in depth. It is revealed that the current heterogeneity during the turn‐on transient is primarily resulted from the Gate signal delay caused by the Gate Runner metallization, and the lateral interaction from adjacent semiconductor regions adds to this inhomogeneity; however, this situation can be improved once the electrical distance between each Anode contact and the Anode electrode gets lowered. Design method for turn‐on performance improvement is also proposed accordingly. Besides, based on the analysis conducted on the multi‐cell simulation results, the possible reason of the extremely slow current rise transient phase is speculated and experimentally verified. The improvement in the comprehension of SiC GTO's turn‐on transient, which cannot be obtained from the traditional investigation from the viewpoint of one elementary cell, will provide guiding principles helping in directing future efforts to advance the improvement of device design technology.
- Open Access
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 369-380
Investigation on the Degradation Mechanism of Si/SiC Cascode Device Under Repetitive Short-Circuit Tests
The Si/SiC Cascode device has been widely accepted in various applications, however, its reliability issue still remains a major concern and needs to be extensively investigated. In this paper, the degradation of a 750 V Si/SiC Cascode device under repetitive short-circuit (SC) tests is investigated at 400 V DC-link voltage. Static and dynamic characteristics are measured before and after the repetitive SC cycles. As the SC cycle increases, the degradation of the device becomes gradually significant. By linking changes in electrical properties to metallization degradation, the physical mechanism of device degradation has been uncovered in depth. Experimental results show that the continuous stress under repetitive SC cycle leads to an increase in the on-state resistance of Si/SiC Cascode device. Finite-element-model (FEM) simulations show that due to the pad current crowding in the source region, the source Al metallization temperature of the SiC JFET rapidly increases to the melting point and undergoes reconstruction, resulting in a significant increase in the source Al metallization resistance. In addition, it is found by scanning electron microscopy (SEM) that the gate metal aluminum of SiC JFET chip also undergoes reconstruction, which is the reason for the degradation of the dynamic characteristics. The research in this paper will provide useful evidences for device manufactures to design Si/SiC Cascode device with high reliability.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 369-380
Open AccessInvestigation on the Degradation Mechanism of Si/SiC Cascode Device Under Repetitive Short-Circuit Tests
The Si/SiC Cascode device has been widely accepted in various applications, however, its reliability issue still remains a major concern and needs to be extensively investigated. In this paper, the degradation of a 750 V Si/SiC Cascode device under repetitive short-circuit (SC) tests is investigated at 400 V DC-link voltage. Static and dynamic characteristics are measured before and after the repetitive SC cycles. As the SC cycle increases, the degradation of the device becomes gradually significant. By linking changes in electrical properties to metallization degradation, the physical mechanism of device degradation has been uncovered in depth. Experimental results show that the continuous stress under repetitive SC cycle leads to an increase in the on-state resistance of Si/SiC Cascode device. Finite-element-model (FEM) simulations show that due to the pad current crowding in the source region, the source Al metallization temperature of the SiC JFET rapidly increases to the melting point and undergoes reconstruction, resulting in a significant increase in the source Al metallization resistance. In addition, it is found by scanning electron microscopy (SEM) that the gate metal aluminum of SiC JFET chip also undergoes reconstruction, which is the reason for the degradation of the dynamic characteristics. The research in this paper will provide useful evidences for device manufactures to design Si/SiC Cascode device with high reliability.
- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (3) , 1176-1180
Modeling Irradiation-Induced Degradation for 4H-SiC Power MOSFETs
In this article, we proposed a comprehensive model for predicting the degradation of SiC MOSFETs after gamma-ray irradiation. It is experimentally founded that SiC MOSFETs exhibit different degradation behaviors under gate bias (i.e.,${V}_{\text {GS}} =15$ V and${V}_{\text {DS}} $ = 0 V) and drain bias (i.e.,${V}_{\text {GS}} $ = 0 V and${V}_{\text {DS}} =400$ V) in terms of threshold voltage (${V}_{\text {TH}}$ ) and ON-resistance (${R}_{\text {ds}, \text{ON}}$ ). TCAD simulation shows that gate bias causes a high electric field in gate oxide above the MOS channel region, while drain bias generates relatively lower electric field in gate oxide around near-channel region. The differences in electric field under gate bias and drain bias lead to different hole yields and charge accumulation in gate oxide, which is the underlying physical mechanism for their different degradation behaviors.${V}_{\text {TH}}$ is chosen as the parameter to quantify the accumulated charges in gate oxide and further predict irradiation-induced degradation. The relationship between the variation of threshold voltage (${\Delta} {V}_{\text {TH}}$ ) and the total ionizing doses (TIDs) under both gate and drain bias is formulated and validated. Comparison among measured data, TCAD simulation, and model prediction shows that the maximum prediction error is lower than 0.08 V, which proves the rationale and accuracy of the proposed degradation model. In addition, the two submodels for gate bias and drain bias are unified as one according to the time dependence effect (TDE) for TID irradiation. The proposed model could be useful to predict the degradation and/or lifetime of SiC MOSFETs in irradiation environments.- 9 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (3) , 1176-1180
Modeling Irradiation-Induced Degradation for 4H-SiC Power MOSFETs
In this article, we proposed a comprehensive model for predicting the degradation of SiC MOSFETs after gamma-ray irradiation. It is experimentally founded that SiC MOSFETs exhibit different degradation behaviors under gate bias (i.e.,${V}_{\text {GS}} =15$ V and${V}_{\text {DS}} $ = 0 V) and drain bias (i.e.,${V}_{\text {GS}} $ = 0 V and${V}_{\text {DS}} =400$ V) in terms of threshold voltage (${V}_{\text {TH}}$ ) and ON-resistance (${R}_{\text {ds}, \text{ON}}$ ). TCAD simulation shows that gate bias causes a high electric field in gate oxide above the MOS channel region, while drain bias generates relatively lower electric field in gate oxide around near-channel region. The differences in electric field under gate bias and drain bias lead to different hole yields and charge accumulation in gate oxide, which is the underlying physical mechanism for their different degradation behaviors.${V}_{\text {TH}}$ is chosen as the parameter to quantify the accumulated charges in gate oxide and further predict irradiation-induced degradation. The relationship between the variation of threshold voltage (${\Delta} {V}_{\text {TH}}$ ) and the total ionizing doses (TIDs) under both gate and drain bias is formulated and validated. Comparison among measured data, TCAD simulation, and model prediction shows that the maximum prediction error is lower than 0.08 V, which proves the rationale and accuracy of the proposed degradation model. In addition, the two submodels for gate bias and drain bias are unified as one according to the time dependence effect (TDE) for TID irradiation. The proposed model could be useful to predict the degradation and/or lifetime of SiC MOSFETs in irradiation environments.- 3 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (11) , 6241-6248
Modeling and Analysis of SiC GTO Thyristor’s Dynamic Turn-On Transient
The fast turn-on speed of silicon carbide (SiC) gate-turn-off (GTO) thyristor is preferred for pulse power applications. However, the turn-on delay phenomenon hinders its improvement. In this article, the dynamic turn-on transient process of SiC GTO thyristor is investigated and analyzed extensively by means of both numerical simulation and physical modeling. The physical mechanism behind its turn-on transient process is discussed in detail. A physical model based on the charge-control theory is proposed to identify the dominant factors influencing the dynamic turn-on transient. Then the theoretical analysis is quantitatively made on the parameter design of GTO’s unit cell, and methods to increase the turn-on switch speed are extensively discussed. This study provides not only in-depth physical insights into the device’s turn-on characteristics, but also designs guidelines for the advancement of SiC GTO thyristor.
- 3 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (11) , 6241-6248
Modeling and Analysis of SiC GTO Thyristor’s Dynamic Turn-On Transient
The fast turn-on speed of silicon carbide (SiC) gate-turn-off (GTO) thyristor is preferred for pulse power applications. However, the turn-on delay phenomenon hinders its improvement. In this article, the dynamic turn-on transient process of SiC GTO thyristor is investigated and analyzed extensively by means of both numerical simulation and physical modeling. The physical mechanism behind its turn-on transient process is discussed in detail. A physical model based on the charge-control theory is proposed to identify the dominant factors influencing the dynamic turn-on transient. Then the theoretical analysis is quantitatively made on the parameter design of GTO’s unit cell, and methods to increase the turn-on switch speed are extensively discussed. This study provides not only in-depth physical insights into the device’s turn-on characteristics, but also designs guidelines for the advancement of SiC GTO thyristor.
- 25 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (9) , 5104-5109
A Novel 4H-SiC JBS-Integrated MOSFET With Self-Pinching Structure for Improved Short-Circuit Capability
Monolithic integration of junction barrier-controlled Schottky (JBS) diode with SiC MOSFET (termed JMOS) offers unique advantages. However, the short-circuit (SC) ruggedness issue stands in the way of the development of the conventional JMOS. The purpose of this numerical study is to investigate a new 4H-SiC JMOS with a self-pinching (SP) structure formed in the JFET region (termed SP-JMOS). The SP structure features that an N-type current spread layer is sandwiched between the P+ layer and the buried P-shield layer, forming a lateral JFET channel. In the forward conduction state, the lateral JFET channel self-pinches off and clamps the potential, thus limiting the saturation current of the device. In the blocking state, both the P+ layer and the buried P-shield layer collaboratively shield the Schottky contact and the SiC/SiO 2 interface from a high electric field for long-term reliable operation. Numerical simulation results show that the proposed SP-JMOS not only withstands a roughly $2.6\times $ longer SC withstanding time than that of the conventional JMOS, but also shows an ultralow oxide electric field in the SP-JMOS.
- 25 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (9) , 5104-5109
A Novel 4H-SiC JBS-Integrated MOSFET With Self-Pinching Structure for Improved Short-Circuit Capability
Monolithic integration of junction barrier-controlled Schottky (JBS) diode with SiC MOSFET (termed JMOS) offers unique advantages. However, the short-circuit (SC) ruggedness issue stands in the way of the development of the conventional JMOS. The purpose of this numerical study is to investigate a new 4H-SiC JMOS with a self-pinching (SP) structure formed in the JFET region (termed SP-JMOS). The SP structure features that an N-type current spread layer is sandwiched between the P+ layer and the buried P-shield layer, forming a lateral JFET channel. In the forward conduction state, the lateral JFET channel self-pinches off and clamps the potential, thus limiting the saturation current of the device. In the blocking state, both the P+ layer and the buried P-shield layer collaboratively shield the Schottky contact and the SiC/SiO 2 interface from a high electric field for long-term reliable operation. Numerical simulation results show that the proposed SP-JMOS not only withstands a roughly $2.6\times $ longer SC withstanding time than that of the conventional JMOS, but also shows an ultralow oxide electric field in the SP-JMOS.
- 10 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4757-4760
Exploration on Electrical Isolation Between High-Voltage SiC Thyristor and Small-Signal Devices for Smart Power Devices
The Smart Discrete concept which monolithically integrates a vertical high-voltage power device with low-voltage smart circuits has been widely adopted in silicon world for many years and may bring similar benefits to SiC world. For example, it is highly desirable to integrate a gate driver circuit onto a high-voltage SiC thyristor for ultra-fast turn-on. However, the electrical isolation between the vertical high-voltage power device and the low-voltage circuit elements remains a major technical challenge for silicon, and even more so for SiC due to the very limited processing options. In this article, we propose a combination of shallow junction isolation (JI) and partial dielectric isolation (DI) for high-voltage 4H-SiC smart thyristor, which is monolithically integrated with low-voltage nMESFET circuits. The characterization of fabricated devices and analysis of leakage currents across the isolation structure have been done to experimentally verify the feasibility of the isolation method. 8 V parasitic lateral NPNP thyristor between a 6.3 kV 4H-SiC thyristor and isolation moats, 175 V lateral PNP transistor between the passive resistor and isolation moats, and 10 V lateral reverse-biased p-n diode between nMESFET and isolation moats are experimentally demonstrated.
- 10 June 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (8) , 4757-4760
Exploration on Electrical Isolation Between High-Voltage SiC Thyristor and Small-Signal Devices for Smart Power Devices
The Smart Discrete concept which monolithically integrates a vertical high-voltage power device with low-voltage smart circuits has been widely adopted in silicon world for many years and may bring similar benefits to SiC world. For example, it is highly desirable to integrate a gate driver circuit onto a high-voltage SiC thyristor for ultra-fast turn-on. However, the electrical isolation between the vertical high-voltage power device and the low-voltage circuit elements remains a major technical challenge for silicon, and even more so for SiC due to the very limited processing options. In this article, we propose a combination of shallow junction isolation (JI) and partial dielectric isolation (DI) for high-voltage 4H-SiC smart thyristor, which is monolithically integrated with low-voltage nMESFET circuits. The characterization of fabricated devices and analysis of leakage currents across the isolation structure have been done to experimentally verify the feasibility of the isolation method. 8 V parasitic lateral NPNP thyristor between a 6.3 kV 4H-SiC thyristor and isolation moats, 175 V lateral PNP transistor between the passive resistor and isolation moats, and 10 V lateral reverse-biased p-n diode between nMESFET and isolation moats are experimentally demonstrated.
- 27 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4571-4576
Numerical Study of SiC MOSFET With Integrated n-/n-Type Poly-Si/SiC Heterojunction Freewheeling Diode
It is highly desirable to monolithically integrate a high-performance freewheeling diode (FWD) in both Si and SiC power MOSFETs for power electronic applications. This is especially true for a SiC MOSFET since its inherent body diode has a very large turn-on knee voltage (~2.7 V). The purpose of this numerical study is to investigate a new 1200 V SiC MOSFET structure with an integrated heterojunction diode formed between n-type polysilicon and n-type SiC (termed HJD-MOSFET). The proposed HJD-MOSFET uses a mesa structure to accommodate the heterojunction FWD without sacrificing any active area while leaving the split-gate planar MOSFET cells in the trench. A p-shield region surrounding the heterojunction, along with the p-base of the MOS cells, shields high electric fields and maintains a high breakdown voltage. Three key HJD-MOSFET device parameters are identified and optimized in this article. The HJD-MOSFET offers a turn-on knee voltage of 0.5 V, roughly five times lower than the intrinsic SiC body diode or two times lower than a typical SiC Schottky barrier diode due to the low barrier height of the n/n heterojunction (~0.68 eV). Finally, the gate charge of HJD-MOSFET is reduced by 42% compared with conventional MOSFET since the poly-Si gate electrode is significantly reduced to accommodate the heterojunction FWD.
- 27 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4571-4576
Numerical Study of SiC MOSFET With Integrated n-/n-Type Poly-Si/SiC Heterojunction Freewheeling Diode
It is highly desirable to monolithically integrate a high-performance freewheeling diode (FWD) in both Si and SiC power MOSFETs for power electronic applications. This is especially true for a SiC MOSFET since its inherent body diode has a very large turn-on knee voltage (~2.7 V). The purpose of this numerical study is to investigate a new 1200 V SiC MOSFET structure with an integrated heterojunction diode formed between n-type polysilicon and n-type SiC (termed HJD-MOSFET). The proposed HJD-MOSFET uses a mesa structure to accommodate the heterojunction FWD without sacrificing any active area while leaving the split-gate planar MOSFET cells in the trench. A p-shield region surrounding the heterojunction, along with the p-base of the MOS cells, shields high electric fields and maintains a high breakdown voltage. Three key HJD-MOSFET device parameters are identified and optimized in this article. The HJD-MOSFET offers a turn-on knee voltage of 0.5 V, roughly five times lower than the intrinsic SiC body diode or two times lower than a typical SiC Schottky barrier diode due to the low barrier height of the n/n heterojunction (~0.68 eV). Finally, the gate charge of HJD-MOSFET is reduced by 42% compared with conventional MOSFET since the poly-Si gate electrode is significantly reduced to accommodate the heterojunction FWD.
- 18 December 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 36 (2) , 025009
Physical modeling and design optimization of 4H-SiC insulated gate bipolar transistors for dv / dt reduction
The extremely high dv / dt of 4H-SiC insulated gate bipolar transistor (IGBT) becomes the major concern in its next-generation large-volume power conversion applications because severe electromagnetic interference (EMI) is induced. However, the root reason for its high dv / dt and the method of suppressing EMI have not been extensively investigated yet. In this paper, we proposed a novel physical model for SiC IGBT to identify the major limiting device design parameters of dv / dt during switching transients. The influences of SiC IGBT’s design parameters on its dv / dt and power dissipation are quantitatively analyzed by means of the physical model. Comparisons between the theoretical predictions and technology computer-aided design simulation results validate the physical model. The results on design optimization of a 18 kV n -channel SiC IGBT shows that 80% reduction of dv / dt and 60% reduction in turn-off power dissipation are achieved simultaneously without sacrificing its forward voltage drop.
- 18 December 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 36 (2) , 025009
Physical modeling and design optimization of 4H-SiC insulated gate bipolar transistors for dv / dt reduction
The extremely high dv / dt of 4H-SiC insulated gate bipolar transistor (IGBT) becomes the major concern in its next-generation large-volume power conversion applications because severe electromagnetic interference (EMI) is induced. However, the root reason for its high dv / dt and the method of suppressing EMI have not been extensively investigated yet. In this paper, we proposed a novel physical model for SiC IGBT to identify the major limiting device design parameters of dv / dt during switching transients. The influences of SiC IGBT’s design parameters on its dv / dt and power dissipation are quantitatively analyzed by means of the physical model. Comparisons between the theoretical predictions and technology computer-aided design simulation results validate the physical model. The results on design optimization of a 18 kV n -channel SiC IGBT shows that 80% reduction of dv / dt and 60% reduction in turn-off power dissipation are achieved simultaneously without sacrificing its forward voltage drop.