Guosong Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guosong Zhang has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Geir Pedersen
Institute of Marine Research, Research Group Observation Methodologies and Acoustics
4 shared publications - Alessandro Cresci
Institute of Marine Research, Acoustics and Observation Methodologies Research Group Austevoll Research Station Storebø Norway
3 shared publications - Bjørn Arne Krafft
Institute of Marine Research (IMR), Norway
2 shared publications - Erik Rodriguez
DS LABS, 01015 Vitoria-Gasteiz, Spain
2 shared publications Hefeng Dong
Department of Electronic Systems Norwegian University of Science and Technology Trondheim Trøndelag Norway
2 shared publications- Henning Wehde
Institute of Marine Research, N-5817 Bergen, Norway
2 shared publications
Latest Publications
- Open Access
- 6 March 2026
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 83 (3)
A novel application of passive acoustic monitoring for detecting tidal constituents through low-frequency ambient noise variability
Understanding tidal variability is essential for safe navigation, coastal development, and environmental management. However, traditional tidal observations from tide gauges, pressure sensors, or satellite altimetry remain sparse in many remote polar regions. This study demonstrates that passive acoustic monitoring (PAM) systems, originally developed to record marine mammal vocalizations, can be repurposed as an effective supplementary source of tidal information. We analyzed low-frequency ambient noise (0.5–5 Hz) recorded by long-term PAM moorings in the Scotia and Lazarev Seas to investigate acoustic signatures associated with tidal influences. Noise levels exhibited significant temporal variability, and power spectral analysis revealed distinct cyclic patterns corresponding to major tidal constituents, including the luni-solar diurnal constituent (${{K}_1}$), the principal lunar diurnal constituent (${{O}_1}$), and the solar semidiurnal (${{S}_2}$) and lunar semidiurnal (${{M}_2}$) constituents. These acoustic detections were consistent with co-located conductivity–temperature–depth measurements and predictions from the TPXO tidal model. Our results highlight the potential of low-frequency ambient noise as a proxy for tidal dynamics and demonstrate the practicality, cost-effectiveness, and scientific value of reusing PAM datasets for oceanographic applications. This approach provides a novel and scalable method to augment tidal monitoring in data-sparse regions, particularly in the Southern Ocean.
- 6 March 2026
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 83 (3)
Open AccessA novel application of passive acoustic monitoring for detecting tidal constituents through low-frequency ambient noise variability
Understanding tidal variability is essential for safe navigation, coastal development, and environmental management. However, traditional tidal observations from tide gauges, pressure sensors, or satellite altimetry remain sparse in many remote polar regions. This study demonstrates that passive acoustic monitoring (PAM) systems, originally developed to record marine mammal vocalizations, can be repurposed as an effective supplementary source of tidal information. We analyzed low-frequency ambient noise (0.5–5 Hz) recorded by long-term PAM moorings in the Scotia and Lazarev Seas to investigate acoustic signatures associated with tidal influences. Noise levels exhibited significant temporal variability, and power spectral analysis revealed distinct cyclic patterns corresponding to major tidal constituents, including the luni-solar diurnal constituent (${{K}_1}$), the principal lunar diurnal constituent (${{O}_1}$), and the solar semidiurnal (${{S}_2}$) and lunar semidiurnal (${{M}_2}$) constituents. These acoustic detections were consistent with co-located conductivity–temperature–depth measurements and predictions from the TPXO tidal model. Our results highlight the potential of low-frequency ambient noise as a proxy for tidal dynamics and demonstrate the practicality, cost-effectiveness, and scientific value of reusing PAM datasets for oceanographic applications. This approach provides a novel and scalable method to augment tidal monitoring in data-sparse regions, particularly in the Southern Ocean.
- Open Access
- 7 November 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (11)
Behavioural responses of overwintering herring to candidate whale deterrent signals
Whales and fisheries targeting the same resources may have unfortunate consequences. Whales may become entangled in fishing gear and injured, or the gear may be damaged, and the catch lost. Acoustic signals can be used to deter whales from such interactions. However, to be efficient, the signals should not alter the behaviour of the target species and thereby reduce the catchability for the fishery. In this study, we examined the behavioural response of overwintering Atlantic herring (Clupea harengus) in a Norwegian fjord to acoustic signals under development for use in deterring humpback and killer whales during fishing operations. The signals were of 0.2 s duration, less than 0.005 s rise time and spanned frequencies from 200 to 3200 Hz. Volume backscattering strength (SV) versus depth (z) was measured before, during and after sound transmission. Herring density, abundance, location and dispersion, as estimated by SV, did not change significantly following the transmissions. This indicates that herring did not change their spatial distribution or orientation in response to the transmissions. We therefore conclude that the signals, at the levels tested, may be used without affecting the behaviour of overwintering herring.
- 7 November 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (11)
Open AccessBehavioural responses of overwintering herring to candidate whale deterrent signals
Whales and fisheries targeting the same resources may have unfortunate consequences. Whales may become entangled in fishing gear and injured, or the gear may be damaged, and the catch lost. Acoustic signals can be used to deter whales from such interactions. However, to be efficient, the signals should not alter the behaviour of the target species and thereby reduce the catchability for the fishery. In this study, we examined the behavioural response of overwintering Atlantic herring (Clupea harengus) in a Norwegian fjord to acoustic signals under development for use in deterring humpback and killer whales during fishing operations. The signals were of 0.2 s duration, less than 0.005 s rise time and spanned frequencies from 200 to 3200 Hz. Volume backscattering strength (SV) versus depth (z) was measured before, during and after sound transmission. Herring density, abundance, location and dispersion, as estimated by SV, did not change significantly following the transmissions. This indicates that herring did not change their spatial distribution or orientation in response to the transmissions. We therefore conclude that the signals, at the levels tested, may be used without affecting the behaviour of overwintering herring.
- Open Access
- 1 May 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (5)
Automated krill body length estimation based on stereo camera images
The fishery for Antarctic krill (Euphausia superba) is the largest by tonnage in the Southern Ocean, and understanding its population dynamics is essential for the sustainable management of this fishery. The standard method for calculating Antarctic krill biomass relies on hydroacoustic survey data and incorporates krill body length data collected concurrently. Traditional scientific acoustic surveys involve manually measuring the body lengths of individual krill caught using fine- meshed nets or trawls along acoustic transects. This work is resource-demanding and could represent a source of human error. To address these challenges, we develop and test an alternative, more automated method for estimating krill body length data by employing an in-trawl stereo camera system. This system collects images that are automatically processed by a custom-trained machine learning model. The results from the machine learning model are then compared to manually measured krill subsampled from the total catch of the corresponding trawl hauls. We demonstrated the ability to extract body lengths from underwater images. However, our results highlighted uncertainties, which we propose addressing by incorporating more advanced camera technology and optimizing the observation section of the small-meshed two-layer krill trawl.
- 1 May 2025
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (5)
Open AccessAutomated krill body length estimation based on stereo camera images
The fishery for Antarctic krill (Euphausia superba) is the largest by tonnage in the Southern Ocean, and understanding its population dynamics is essential for the sustainable management of this fishery. The standard method for calculating Antarctic krill biomass relies on hydroacoustic survey data and incorporates krill body length data collected concurrently. Traditional scientific acoustic surveys involve manually measuring the body lengths of individual krill caught using fine- meshed nets or trawls along acoustic transects. This work is resource-demanding and could represent a source of human error. To address these challenges, we develop and test an alternative, more automated method for estimating krill body length data by employing an in-trawl stereo camera system. This system collects images that are automatically processed by a custom-trained machine learning model. The results from the machine learning model are then compared to manually measured krill subsampled from the total catch of the corresponding trawl hauls. We demonstrated the ability to extract body lengths from underwater images. However, our results highlighted uncertainties, which we propose addressing by incorporating more advanced camera technology and optimizing the observation section of the small-meshed two-layer krill trawl.
- 22 February 2025
- Published by Wiley in Limnology and Oceanography: Methods
- Vol. 23 (6) , 425-437
Resolving acoustic azimuth using an accelerometer‐based underwater acoustic vector sensor
The performance of a single commercial accelerometer‐based underwater acoustic vector sensor (AVS) in resolving acoustic azimuth was evaluated. The method involves calculating the active intensity of an acoustic signal to determine the dominant directionality of an acoustic pressure field as a function of time and frequency. While this method efficiently displays azimuth bearings for specific frequencies, there are very few assessments of its performance in resolving all possible bearings using a single AVS. Field experiments were conducted with an AVS placed on the sea bottom and an active source suspended from a research vessel. A 600 Hz signal was transmitted from 16 positions covering a 360° azimuth to the AVS. During the transmissions, the vessel maintained its position and heading by using a dynamic positioning system. The acoustic azimuths were compared with the transmission bearings obtained via Global Positioning System. This study demonstrates that a commercial AVS system can effectively resolve acoustic bearings across a full 360° azimuth at high signal‐to‐noise ratios using the active intensity method. Our results support the use of AVS systems in research on sound directionality, including bioacoustics studies on how marine organisms respond to natural underwater sound and anthropogenic noise.
- 22 February 2025
- Published by Wiley in Limnology and Oceanography: Methods
- Vol. 23 (6) , 425-437
Resolving acoustic azimuth using an accelerometer‐based underwater acoustic vector sensor
The performance of a single commercial accelerometer‐based underwater acoustic vector sensor (AVS) in resolving acoustic azimuth was evaluated. The method involves calculating the active intensity of an acoustic signal to determine the dominant directionality of an acoustic pressure field as a function of time and frequency. While this method efficiently displays azimuth bearings for specific frequencies, there are very few assessments of its performance in resolving all possible bearings using a single AVS. Field experiments were conducted with an AVS placed on the sea bottom and an active source suspended from a research vessel. A 600 Hz signal was transmitted from 16 positions covering a 360° azimuth to the AVS. During the transmissions, the vessel maintained its position and heading by using a dynamic positioning system. The acoustic azimuths were compared with the transmission bearings obtained via Global Positioning System. This study demonstrates that a commercial AVS system can effectively resolve acoustic bearings across a full 360° azimuth at high signal‐to‐noise ratios using the active intensity method. Our results support the use of AVS systems in research on sound directionality, including bioacoustics studies on how marine organisms respond to natural underwater sound and anthropogenic noise.
- 2 July 2024
- Published by Taylor & Francis in Bioacoustics
- Vol. 33 (5) , 460-477
Characterisation of grunt sound pressure level from spawning Atlantic cod ( Gadus morhua )
- 2 July 2024
- Published by Taylor & Francis in Bioacoustics
- Vol. 33 (5) , 460-477
Characterisation of grunt sound pressure level from spawning Atlantic cod ( Gadus morhua )
- Open Access
- 11 May 2024
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (3)
Answering the key stakeholder questions about the impact of offshore wind farms on marine life using hypothesis testing to inform targeted monitoring
Stakeholders need scientific advice on the environmental impacts of offshore wind (OW) before the facilities are installed. The utility of conventional environmental monitoring methods as a basis for forecasting OW impacts is limited because they do not explain the causes of the observed effects. We propose a multistep approach, based on process-oriented hypothesis testing, targeted monitoring and numerical modeling, to answer key stakeholder questions about planning an OW facility: Q1—Where do we place future OW farms so that impacts on the ecosystem are minimized? Q2—Which species and ecosystem processes will be impacted and to what degree? Q3—Can we mitigate impacts and, if so, how? and Q4—What are the risks of placing an OW facility in one location vs. another? Hypothesis testing can be used to assess impacts of OW facilities on target species-ecological process. This knowledge is transferable and is broadly applicable, a priori, to assess suitable locations for OW (Q1). Hypothesis testing can be combined with monitoring methods to guide targeted monitoring. The knowledge generated can identify the species/habitats at risk (Q2), help selecting/developing mitigation measures (Q3), and be used as input parameters for models to forecast OW impacts at a large spatial scale (Q1; Q4).
- 11 May 2024
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 82 (3)
Open AccessAnswering the key stakeholder questions about the impact of offshore wind farms on marine life using hypothesis testing to inform targeted monitoring
Stakeholders need scientific advice on the environmental impacts of offshore wind (OW) before the facilities are installed. The utility of conventional environmental monitoring methods as a basis for forecasting OW impacts is limited because they do not explain the causes of the observed effects. We propose a multistep approach, based on process-oriented hypothesis testing, targeted monitoring and numerical modeling, to answer key stakeholder questions about planning an OW facility: Q1—Where do we place future OW farms so that impacts on the ecosystem are minimized? Q2—Which species and ecosystem processes will be impacted and to what degree? Q3—Can we mitigate impacts and, if so, how? and Q4—What are the risks of placing an OW facility in one location vs. another? Hypothesis testing can be used to assess impacts of OW facilities on target species-ecological process. This knowledge is transferable and is broadly applicable, a priori, to assess suitable locations for OW (Q1). Hypothesis testing can be combined with monitoring methods to guide targeted monitoring. The knowledge generated can identify the species/habitats at risk (Q2), help selecting/developing mitigation measures (Q3), and be used as input parameters for models to forecast OW impacts at a large spatial scale (Q1; Q4).
- Open Access
- 13 October 2023
- Published by EDP Sciences in Acta Acustica
- Vol. 7, 46
Determining the directionality of anthropogenic noise using an underwater acoustic vector sensor: a case study in a Norwegian fjord
Sources of anthropogenic noise in the ocean have temporal and directional characteristics. Characterizing the soundscape requires identifying the directionality of the sources of noise in addition to the non-directional sound pressure. An underwater acoustic vector sensor (AVS) can be used to provide the directionality of incoming noise, and the concomitant sound pressure. We present an analysis of measurements from an AVS deployed in a Norwegian fjord in which there is frequent commercial ship traffic. We assessed the directionality of various known and unknown noise sources and used it to interpret the associated sound pressure. The fjord soundscape consists of time-varying noise directionality and intensity from anthropogenic sources, especially shipping activity. This case study highlights the benefits of using information from an AVS to assess noise directionality in a soundscape.
- 13 October 2023
- Published by EDP Sciences in Acta Acustica
- Vol. 7, 46
Open AccessDetermining the directionality of anthropogenic noise using an underwater acoustic vector sensor: a case study in a Norwegian fjord
Sources of anthropogenic noise in the ocean have temporal and directional characteristics. Characterizing the soundscape requires identifying the directionality of the sources of noise in addition to the non-directional sound pressure. An underwater acoustic vector sensor (AVS) can be used to provide the directionality of incoming noise, and the concomitant sound pressure. We present an analysis of measurements from an AVS deployed in a Norwegian fjord in which there is frequent commercial ship traffic. We assessed the directionality of various known and unknown noise sources and used it to interpret the associated sound pressure. The fjord soundscape consists of time-varying noise directionality and intensity from anthropogenic sources, especially shipping activity. This case study highlights the benefits of using information from an AVS to assess noise directionality in a soundscape.
- Open Access
- 19 November 2020
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 77 (7-8) , 2954-2959
In situ calibration of observatory broadband echosounders
Today, numerous scientific echosounders are used as continuously monitoring systems in ocean observatories. These echosounders are usually calibrated in shallow water, either in laboratory tanks or at random ocean docks before deployments. If the systems are used for quantitative measurements by the observatories, they should be calibrated at the operating depths to consider the environmental effects on the calibration parameters. In this article, a simple in situ calibration method is presented, which was recently applied to one of the nodes of the Norwegian Lofoten-Vesterålen ocean observatory, when the research vessel with dynamic positioning system suspended and moved the calibration sphere between the vessel and the transducer. The calibration results of a 70-kHz split-beam echosounder demonstrate that this method can be applied to the cabled observatories.
- 19 November 2020
- Published by Oxford University Press (OUP) in ICES Journal of Marine Science
- Vol. 77 (7-8) , 2954-2959
Open AccessIn situ calibration of observatory broadband echosounders
Today, numerous scientific echosounders are used as continuously monitoring systems in ocean observatories. These echosounders are usually calibrated in shallow water, either in laboratory tanks or at random ocean docks before deployments. If the systems are used for quantitative measurements by the observatories, they should be calibrated at the operating depths to consider the environmental effects on the calibration parameters. In this article, a simple in situ calibration method is presented, which was recently applied to one of the nodes of the Norwegian Lofoten-Vesterålen ocean observatory, when the research vessel with dynamic positioning system suspended and moved the calibration sphere between the vessel and the transducer. The calibration results of a 70-kHz split-beam echosounder demonstrate that this method can be applied to the cabled observatories.
- Open Access
An Automated Pipeline for Image Processing and Data Treatment to Track Activity Rhythms of Paragorgia arborea in Relation to Hydrographic Conditions
Imaging technologies are being deployed on cabled observatory networks worldwide. They allow for the monitoring of the biological activity of deep-sea organisms on temporal scales that were never attained before. In this paper, we customized Convolutional Neural Network image processing to track behavioral activities in an iconic conservation deep-sea species—the bubblegum coral Paragorgia arborea—in response to ambient oceanographic conditions at the Lofoten-Vesterålen observatory. Images and concomitant oceanographic data were taken hourly from February to June 2018. We considered coral activity in terms of bloated, semi-bloated and non-bloated surfaces, as proxy for polyp filtering, retraction and transient activity, respectively. A test accuracy of 90.47% was obtained. Chronobiology-oriented statistics and advanced Artificial Neural Network (ANN) multivariate regression modeling proved that a daily coral filtering rhythm occurs within one major dusk phase, being independent from tides. Polyp activity, in particular extrusion, increased from March to June, and was able to cope with an increase in chlorophyll concentration, indicating the existence of seasonality. Our study shows that it is possible to establish a model for the development of automated pipelines that are able to extract biological information from times series of images. These are helpful to obtain multidisciplinary information from cabled observatory infrastructures.
Open AccessAn Automated Pipeline for Image Processing and Data Treatment to Track Activity Rhythms of Paragorgia arborea in Relation to Hydrographic Conditions
Imaging technologies are being deployed on cabled observatory networks worldwide. They allow for the monitoring of the biological activity of deep-sea organisms on temporal scales that were never attained before. In this paper, we customized Convolutional Neural Network image processing to track behavioral activities in an iconic conservation deep-sea species—the bubblegum coral Paragorgia arborea—in response to ambient oceanographic conditions at the Lofoten-Vesterålen observatory. Images and concomitant oceanographic data were taken hourly from February to June 2018. We considered coral activity in terms of bloated, semi-bloated and non-bloated surfaces, as proxy for polyp filtering, retraction and transient activity, respectively. A test accuracy of 90.47% was obtained. Chronobiology-oriented statistics and advanced Artificial Neural Network (ANN) multivariate regression modeling proved that a daily coral filtering rhythm occurs within one major dusk phase, being independent from tides. Polyp activity, in particular extrusion, increased from March to June, and was able to cope with an increase in chlorophyll concentration, indicating the existence of seasonality. Our study shows that it is possible to establish a model for the development of automated pipelines that are able to extract biological information from times series of images. These are helpful to obtain multidisciplinary information from cabled observatory infrastructures.
- Open Access
- 1 April 2020
- Published by Elsevier in Marine Pollution Bulletin
- Vol. 153, 110948
Measurements of underwater noise radiated by commercial ships at a cabled ocean observatory
- 1 April 2020
- Published by Elsevier in Marine Pollution Bulletin
- Vol. 153, 110948
Open AccessMeasurements of underwater noise radiated by commercial ships at a cabled ocean observatory