Reinhard R. Baumann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Reinhard R. Baumann has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Enrico Sowade
Technische Universität Chemnitz (TUC), Digital Printing and Imaging Technology, 09126 Chemnitz, Germany
4 shared publications - Eloi Ramon
Institut de Microelectrònica de Barcelona, IMB-CNM (CSIC), 08193 Bellaterra, Spain
3 shared publications - Ammar Al-Hamry
Chemnitz University of Technology
2 shared publications - Carme Martínez-Domingo
Institut de Ciència de Materials de Barcelona (ICMAB‐CSIC) Cerdanyola del Vallès Spain
2 shared publications - Kalyan Yoti Mitra
Fraunhofer Institute for Electronic Nano Systems ENAS
2 shared publications Olfa Kanoun
2 shared publications
Latest Publications
- 3 January 2023
- Published by Elsevier in Chemical Engineering Journal
- Vol. 457
Inkjet-printed MoS2-based 3D-structured electrocatalysts on Cu films for ultra-efficient hydrogen evolution reaction
- 3 January 2023
- Published by Elsevier in Chemical Engineering Journal
- Vol. 457
Inkjet-printed MoS2-based 3D-structured electrocatalysts on Cu films for ultra-efficient hydrogen evolution reaction
- Open Access
- 20 March 2022
- Published by Elsevier in Green Analytical Chemistry
- Vol. 1, 100006
A fully-printed electrochemical platform for assisted colorimetric detection of phosphate in saliva: Greenness and whiteness quantification by the AGREE and RGB tools
- 20 March 2022
- Published by Elsevier in Green Analytical Chemistry
- Vol. 1, 100006
Open AccessA fully-printed electrochemical platform for assisted colorimetric detection of phosphate in saliva: Greenness and whiteness quantification by the AGREE and RGB tools
- 1 November 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 346
Functional aqueous-based polyaniline inkjet inks for fully printed high-performance pH-sensitive electrodes
- 1 November 2021
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 346
Functional aqueous-based polyaniline inkjet inks for fully printed high-performance pH-sensitive electrodes
- Open Access
- 26 January 2021
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 6 (1) , 015003
Large-scale fabrication of all-inkjet-printed resistors and WORM memories on flexible polymer films with high yield and stability
We report on the development of inkjet-printed thin-film resistors using both organic and inorganic ink formulations. The passive devices were manufactured on flexible polymer substrates in ambient condition without the need for a cleanroom environment or inert atmosphere and at a maximum temperature of 150 °C. By using the same manufacturing process, the rapid electrical sintering (RES) method is demonstrated as effective for the fabrication of inkjet-printed, programmable Write-Once-Read-Many (WORM) memories. Several hundred fully inkjet-printed resistors with different parameters were fabricated and subsequently morphologically and electrically characterized with the aim of obtaining statistically significant data. From a manufacturing process viewpoint, the procedures based on inkjet printing herein described are highly attractive: they do not require high temperatures, low pressures, special atmospheric conditions, and any masks, therefore providing a versatile low-cost approach to fabricate passive electrical components and simple circuits useful for the electronic industry. Printing can be carried out at a sufficiently low temperature to avoid damage to the fabric substrate and these devices can be used in a range of applications requiring flexible and conformal devices from embedded passive filters in PCBs to wearable electronics.
- 26 January 2021
- Published by IOP Publishing in Flexible and Printed Electronics
- Vol. 6 (1) , 015003
Open AccessLarge-scale fabrication of all-inkjet-printed resistors and WORM memories on flexible polymer films with high yield and stability
We report on the development of inkjet-printed thin-film resistors using both organic and inorganic ink formulations. The passive devices were manufactured on flexible polymer substrates in ambient condition without the need for a cleanroom environment or inert atmosphere and at a maximum temperature of 150 °C. By using the same manufacturing process, the rapid electrical sintering (RES) method is demonstrated as effective for the fabrication of inkjet-printed, programmable Write-Once-Read-Many (WORM) memories. Several hundred fully inkjet-printed resistors with different parameters were fabricated and subsequently morphologically and electrically characterized with the aim of obtaining statistically significant data. From a manufacturing process viewpoint, the procedures based on inkjet printing herein described are highly attractive: they do not require high temperatures, low pressures, special atmospheric conditions, and any masks, therefore providing a versatile low-cost approach to fabricate passive electrical components and simple circuits useful for the electronic industry. Printing can be carried out at a sufficiently low temperature to avoid damage to the fabric substrate and these devices can be used in a range of applications requiring flexible and conformal devices from embedded passive filters in PCBs to wearable electronics.
- Open Access
- 16 December 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (10) , 105708
Customizing hydrothermal properties of inkjet printed sensitive films by functionalization of carbon nanotubes
Multiwalled carbon nanotubes (MWCNTs) are attractive materials for realizing sensors, owing to their high aspect ratio associated with excellent mechanical, electronic, and thermal properties. Moreover, their sensing properties can be tuned by introducing functional groups on their framework and adjusting the processing conditions. In this paper, we investigate the potential of functionalized CNTs for humidity and temperature sensing by optimization of the functionalization, the processing conditions and the printing conditions. The morphology of the differently functionalized MWCNTs is investigated by infrared spectroscopy (IR), scanning electron microscopy, thermogravimetry (TG) and TG-coupled mass-spectrometric studies. Using the functionalized MWCNTs, films were fabricated with different numbers of layers (4, 6, 8, 10 layers) via inkjet printing on a flexible polyimide substrate containing an interdigital microelectrode. The influence of hydrothermal effects was investigated. The sensitivity to humidity is higher for films prepared with MWCNTs functionalized with a high sonication amplitude and a bigger number of layers due to enhancements of hydrophilicity and water mobility. A higher sensitivity to temperature is achieved by a low sonication amplitude and a small number of layers. For the encapsulation of the temperature sensor against humidity, a Bectron layer is proposed, which reduces also the hysteresis effect. This study demonstrates the efficiency of carboxylic functionalized MWCNTs deposit by inkjet printing for realization of sensitive and cost-effective humidity and temperature sensors. It provides a real example for the interesting contribution of functionalization procedures to the sensing properties of MWCNTs films.
- 16 December 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 32 (10) , 105708
Open AccessCustomizing hydrothermal properties of inkjet printed sensitive films by functionalization of carbon nanotubes
Multiwalled carbon nanotubes (MWCNTs) are attractive materials for realizing sensors, owing to their high aspect ratio associated with excellent mechanical, electronic, and thermal properties. Moreover, their sensing properties can be tuned by introducing functional groups on their framework and adjusting the processing conditions. In this paper, we investigate the potential of functionalized CNTs for humidity and temperature sensing by optimization of the functionalization, the processing conditions and the printing conditions. The morphology of the differently functionalized MWCNTs is investigated by infrared spectroscopy (IR), scanning electron microscopy, thermogravimetry (TG) and TG-coupled mass-spectrometric studies. Using the functionalized MWCNTs, films were fabricated with different numbers of layers (4, 6, 8, 10 layers) via inkjet printing on a flexible polyimide substrate containing an interdigital microelectrode. The influence of hydrothermal effects was investigated. The sensitivity to humidity is higher for films prepared with MWCNTs functionalized with a high sonication amplitude and a bigger number of layers due to enhancements of hydrophilicity and water mobility. A higher sensitivity to temperature is achieved by a low sonication amplitude and a small number of layers. For the encapsulation of the temperature sensor against humidity, a Bectron layer is proposed, which reduces also the hysteresis effect. This study demonstrates the efficiency of carboxylic functionalized MWCNTs deposit by inkjet printing for realization of sensitive and cost-effective humidity and temperature sensors. It provides a real example for the interesting contribution of functionalization procedures to the sensing properties of MWCNTs films.
- 5 June 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10246, 102460F
Inkjet-printed dissolved oxygen and pH sensors on flexible plastic substrates
There are a broad range of applications such as analytical sensors, biosensing and medical applications that require the monitoring of dissolved oxygen (DO) and pH using sensitive, stable, compact and low cost sensors. Here we develop full inkjet printing sensors to measure DO and pH. They have been fabricated using commercially available gold and platinum inks in plastic substrates. The inks are specially designed formulation which allows their sintering at temperatures as low as 150 and 190 °C for Au and Pt respectively. This is a key point in the development of low-cost sensors made on plastic and paper substrates. These sensors integrate in a single platform all the basic elements for pH and DO recording, allowing the measures without any external electrode. The DO is directly measured with a gold working electrode, and the pH sensors is achieved after electrodepositing iridium oxide film over platinum working electrode. The printed electrodes for DO sensing exhibits excellent linearity between 0 and 8 mg L _ 1 range, with correlation factors greater than 0.99, obtaining low limits of detection, 0.17 mgL _ 1 and a sensitivity of 0.06 A(mgL) _ 1. IrOx pH sensors exhibit a super-Nernstian response in sensitivity repeatedly and reversibly between 65 mV/pH in the pH range of 3 to 10. This work demonstrates that these sensors are suitable for the determination of DO and pH and provide a cost-effective solution for future electrochemical monitoring systems.
- 5 June 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10246, 102460F
Inkjet-printed dissolved oxygen and pH sensors on flexible plastic substrates
There are a broad range of applications such as analytical sensors, biosensing and medical applications that require the monitoring of dissolved oxygen (DO) and pH using sensitive, stable, compact and low cost sensors. Here we develop full inkjet printing sensors to measure DO and pH. They have been fabricated using commercially available gold and platinum inks in plastic substrates. The inks are specially designed formulation which allows their sintering at temperatures as low as 150 and 190 °C for Au and Pt respectively. This is a key point in the development of low-cost sensors made on plastic and paper substrates. These sensors integrate in a single platform all the basic elements for pH and DO recording, allowing the measures without any external electrode. The DO is directly measured with a gold working electrode, and the pH sensors is achieved after electrodepositing iridium oxide film over platinum working electrode. The printed electrodes for DO sensing exhibits excellent linearity between 0 and 8 mg L _ 1 range, with correlation factors greater than 0.99, obtaining low limits of detection, 0.17 mgL _ 1 and a sensitivity of 0.06 A(mgL) _ 1. IrOx pH sensors exhibit a super-Nernstian response in sensitivity repeatedly and reversibly between 65 mV/pH in the pH range of 3 to 10. This work demonstrates that these sensors are suitable for the determination of DO and pH and provide a cost-effective solution for future electrochemical monitoring systems.
- 1 March 2016
- Published by Elsevier in Organic Electronics
- Vol. 30, 237-246
Up-scaling of the manufacturing of all-inkjet-printed organic thin-film transistors: Device performance and manufacturing yield of transistor arrays
- 1 March 2016
- Published by Elsevier in Organic Electronics
- Vol. 30, 237-246
Up-scaling of the manufacturing of all-inkjet-printed organic thin-film transistors: Device performance and manufacturing yield of transistor arrays
- 1 January 1992
- Published by Springer Nature
- p. 419-423
Permanent Conductivity in Laser Converted Poly(Bis-Ethylthioacetylene) Using an Excimer and Ar+-Laser
- 1 January 1992
- Published by Springer Nature
- p. 419-423
Permanent Conductivity in Laser Converted Poly(Bis-Ethylthioacetylene) Using an Excimer and Ar+-Laser