RTRamoon Barros Lovate Temporim

Ramoon Barros Lovate Temporim

*This is an algorithmically generated author record based on publicly available information.

Ramoon Barros Lovate Temporim has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Assessing the environmental impacts of livestock products in Europe: A consequential life cycle assessment

    by T.C. Ponsioen, P. Goglio, S. Moakes, R. Barros Lovate Temporim, C.P.A. Van Wagenberg, G. Nassy, L. Rocchi, M. Pauselli, B. Valenti

  • Open Access

    Energy and Environmental Valorisation of Residual Wood Pellet by Small Size Residential Heating Systems

    by Valentina Coccia, Ramoon Barros Lovate Temporim, Alessandro Paglianti, Alessia Di Giuseppe, Franco Cotana, Andrea Nicolini

    Particulate matter (PM) emissions from combustion-based heating systems have been identified as a major contributor to environmental issues and human health risks. Particularly, small-scale residential combustion was responsible for 58% of the total PM2.5 emissions in Europe in 2020, with domestic heating using wood-based fuels accounting for around 56% of soot emissions. Reducing PM2.5 emissions has become a major goal of European environmental policies, which have included it among the key targets of the Zero Pollution Action Plan. In this framework, this study presents a performance analysis of a newly developed PM abatement system consisting of a passive cyclone abatement system (PCAS) specifically designed for small residential pellet stoves. The system was tested under steady-state and non-steady-state operating conditions. The experimental results showed that the PCAS abatement system effectively captured PM at a rate of 10.64 mg/MJ, with great efficiency in capturing particles ≥ 10 µm. The heavy metal content in the captured material was below the limit values for agricultural application-destined soil. A Life Cycle Assessment showed that the PCAS could achieve net-zero PM emissions in 1 year and 8 months. Finally, the economic analysis revealed that the PCAS is significantly more cost-effective: over a 10-year period, it could save up to €4000 in installation, maintenance, and energy costs compared to conventional active systems. These findings highlight the effectiveness of this design of PCAS as in reducing PM emissions from residential heating systems and provide valuable insights for the development of future abatement systems.


  • Open Access

    Design and Performance Analysis of a Small-Scale Prototype Water Condensing System for Biomass Combustion Flue Gas Abatement

    by Valentina Coccia, Ramoon Barros Lovate Temporim, Leandro Lunghi, Oleksandra Tryboi, Franco Cotana, Anna Magrini, Daniele Dondi, Dhanalakshmi Vadivel, Marco Cartesegna, Andrea Nicolini

    This article outlines the design and performance of a flue gas condensation system integrated with a biomass combustion plant. The system comprises a biomass plant fuelled by wood chips, generating flue gases. These gases are condensed via a double heat exchanger set-up, extracting water and heat to reduce concentrations of CO, CO2, and NOx while releasing gases at a temperature close to ambient temperature. The 100 kW biomass plant operates steadily, consuming 50 kg of wood chips per hour with fuel energy of 18.98 MJ/kg. Post combustion, the gases exit at 430 °C and undergo two-stage cooling. In the first stage, gases are cooled in a high-temperature tube heat exchanger, transferring heat to air. They then enter the second stage, a flue gas/water heat exchanger, recovering sensible and latent thermal energy, which leads to water condensation. Flue gas is discharged at approximately 33 °C. Throughout, parameters like the flue gas temperatures, mass flow, fuel consumption, heat carrier temperatures, and water condensation rates were monitored. The test results show that the system can condense water from flue gas at 75 g/min at 22 °C while reducing pollutant emissions by approximately 20% for CO2, 19% for CO, 30% for NO, and 26% for NOx.


  • Open Access

    Assessing the environmental performance of optimized commercial refrigerators with alternative refrigerants and remote monitoring system: A cradle-to-grave life cycle assessment

    by Ramoon Barros Lovate Temporim, Alessia Di Giuseppe, Fabiana Frota de Albuquerque Landi, Andrea Nicolini


  • Open Access

    Life Cycle Assessment of Polyol Production from Lignin via Organosolv and Liquefaction Treatments

    by Gianluca Cavalaglio, Ippolita Mecca, Paola Iodice, Tommaso Giannoni, Mattia Gelosia, Andrea Nicolini, Ramoon Barros Lovate Temporim

    This study aimed to conduct a comprehensive Life Cycle Assessment (LCA) of lignin-based polyol production through organosolv fractionation of cardoon stalks and subsequent lignin liquefaction. The LCA employed a cradle-to-gate approach, encompassing cardoon cultivation and all processing steps leading to polyol production. The research involved laboratory-scale optimization of the organosolv and liquefaction processes, followed by industrial-scale implementation. The analysis revealed that all stages of the production chain, including crop cultivation, organosolv, and liquefaction, significantly influenced overall environmental impacts. Specific materials and processes played pivotal roles, such as harvesting machinery and fertilizers in crop production, γ-Valerolactone (GVL) as the primary contributor (72–100%) to environmental impacts in the organosolv phase, and materials like polyethylene glycol 400 (PEG 400) and glycerin in the liquefaction phase, accounting for the majority (96–100%) of environmental impacts in this stage. When considering endpoint damage categories, it became evident that this production chain had a notable impact on human health, primarily due to emissions in air, water, and soil from agricultural processes. Lignin-based polyols demonstrated a moderate improvement compared to their petroleum-based counterparts, with an approximate reduction of 3–16% in environmental impact.


  • Open Access

    Life Cycle Assessment of Cynara cardunculus L. -Based Polygeneration and Biodiesel Chains

    by Ramoon Barros Lovate Temporim, Gianluca Cavalaglio, Alessandro Petrozzi, Valentina Coccia, Franco Cotana, Andrea Nicolini

    Given the current scenario of increasing environmental problems associated with the need for rapid energy transition, this article aimed to investigate the implementation of Cynara cardunculus L. (cardoon), a plant with high environmental performance, as a source of energy resources. This study presented thLife Cycle Assessment of two energy production chains—for the polygeneration of power, heat, and cooling; and to produce biodiesel—fed with cardoon seeds, in addition to comparing these chains with the use of the traditional Italian grids (power and gas) and with the production of diesel based on palm, soybean, and rapeseed. Approximately 49 t of seeds were cultivated and processed, yielding 8.5 t of oil. The system boundaries encompass three main macro-phases, cardoon production, oil extraction, and, depending on the application, energy generation (polygeneration) or transesterification (biodiesel). The models were developed using the software SimaPro V9.3.0.2, and the inventory was based on the database ecoinvent V3.8. The Life Cycle Impact Assessment was performed using the ReCiPe V1.06 method at the midpoint (H) and endpoint (H/A) levels. Crude cardoon oil showed a global warming of 20–55% lower than other vegetable oils (palm, soybean, and rapeseed). In the case of biodiesel production, cardoon-based biodiesel presented a reduction in the impact burden by 12–57% compared to biodiesel based on palm, soybean, and rapeseed. With the use of oil in Polygeneration, a subtle increase in the impact burden was observed, with 13% more impact than the use of Italian power and gas grids.


  • Open Access

    Life Cycle Assessment and Energy Balance of a Polygeneration Plant Fed with Lignocellulosic Biomass of Cynara cardunculus L.

    by Ramoon Barros Lovate Temporim, Gianluca Cavalaglio, Alessandro Petrozzi, Valentina Coccia, Paola Iodice, Andrea Nicolini, Franco Cotana

    This article aims to present an evaluation of the environmental performance of a combustion polygeneration plant fed with lignocellulosic material from cardoon (Cynara cardunculus L.) through the technique of Life Cycle Assessment (LCA). The system boundaries encompassed macro-phases of crop production, transportation, and polygeneration processes that were able to produce 100 kW of electricity, a residual thermal energy recovery system and district heating and cooling with 270 kW of heating, and a 140 kW of cooling. The LCA was performed using Cumulative Energy Demand and ReCiPe Life Cycle Impact Assessment methods through midpoint and endpoint indicators. From 2000 h/year, 165.92 GJ of electricity and 667.23 GJ of primary energy were consumed, and 32.82 tCO2eq were emitted. The rates of Greenhouse Gas (GHG) and energy demand per MJ produced were 0.08 MJSE/MJPD, 0.30 MJPE/MJPD, and 0.01 kgCO2eq/MJPD. According to the ReCiPe method, the impact categories with the highest impact loads were Terrestrial ecotoxicity (2.44%), Freshwater ecotoxicity (32.21%), Marine ecotoxicity (50.10%), Human carcinogenic toxicity (8.75%), and Human non-carcinogenic toxicity (4.76%). Comparing the same energy outputs produced by Italian power and gas grids, the proposed polygeneration plant was able to reduce primary energy demand and GHG emissions by 80 and 81%, respectively, in addition to reducing the emissions of the five main categories of impacts by between 25 and 73%.


  • Open Access

    A Prototype Plant for Oilseed Extraction: Analysis of Mass and Energy Flows

    by Ramoon B. L. Temporim, Alessandro Petrozzi, Valentina Coccia, Franco Cotana, Gianluca Cavalaglio

    The focus of this study is to analyze the energy flows related to cardoon oil processing based on the estimated electricity consumption. It was carried out in a prototype oilseed extraction plant located in Umbria Region, Italy. This installation consists of the following processes: seed weight-storage, transportation, sifting, milling, filtering, and oil storage. Approximately 49,000 kg dry basis (DB) of cardoon seeds (Cynara cardunculus) were processed. Cardoon seeds were chosen as a feedstock due to their sustainability characteristics. Before processing, samples of raw material were analyzed in terms of moisture, oil content, impurity, density, and lower heating value. The input–output flows were measured in terms of weight and energy consumption. Its data were used to perform the mass-energy balance and estimate the efficiency of processes. About 8505 kg of filtered oil was obtained from raw material. The efficiency of the process chain was 84.42% concerning the oil content in the seeds. For the same period, the plant required a total of 17,556 MJ of electric energy from the grid for its operation. 321,507 MJ were obtained from oil and 688,875 MJ from oilcake. About 5.48% of the energy produced by oil extraction was virtually used in the process.