Yan Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yan Xu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Bingheng Lu
The State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an, China
4 shared publications - Jianping Zhou
School of Mechanical Engineering, Xinjiang University, Urumqi 830047, China
3 shared publications Zhengyang Jin
School of Mechanical Engineering , XinJiang University , Urumchi , 830017 , P.R. China
3 shared publications- Hongsheng Liu
School of Mechanical Engineering, Xinjiang University, Urumqi 830049, China
2 shared publications - Kai Li
School of Mechanical Engineering, Xinjiang University
2 shared publications - Ruilei Xue
School of Mechanical Engineering, Xinjiang University, Urumqi 830049, China
2 shared publications
Latest Publications
- Open Access
Gaussian Process-Based Multi-Fidelity Bayesian Optimization for Optimal Calibration Point Selection
Temperature and humidity calibration chambers, which provide controlled environments for instrument testing and validation, are widely applied in the aerospace and biomedicine fields. However, traditional fixed calibration points fail to adapt to complex operational requirements and exhibit problems including a limited coverage range and low efficiency. To address these challenges, this study develops a Gaussian Process-based Multi-Fidelity Bayesian Optimization (GP-MFBO) framework for optimal selection of temperature and humidity calibration points. The framework integrates the following three key components: (1) a three-layer progressive multi-fidelity modeling system comprising physical analytical models, computational fluid dynamics (CFD) numerical simulations, and experimental verification; (2) a systematic uncertainty quantification system covering model uncertainty, parameter uncertainty, and observation uncertainty; and (3) an adaptive acquisition function that balances uncertainty penalty mechanisms and multi-fidelity information gain evaluation. The experimental results demonstrate that the proposed GP-MFBO method achieves optimal calibration point combinations with a temperature uniformity score of 0.149 and humidity uniformity score of 2.38, approaching theoretical optimal solutions within 4.5% and 3.6%, respectively. Compared to standard Gaussian process, Co-Kriging, two-stage optimization, polynomial regression, and traditional single-fidelity methods, GP-MFBO achieves uniformity score improvements of up to 81.7% and 76.3% for temperature and humidity, respectively. The prediction confidence interval coverage reaches 94.2%, outperforming all comparative methods. This research provides a rigorous theoretical foundation and technical solution for the scientific design and reliable operation of large-space temperature and humidity calibration systems.
Open AccessGaussian Process-Based Multi-Fidelity Bayesian Optimization for Optimal Calibration Point Selection
Temperature and humidity calibration chambers, which provide controlled environments for instrument testing and validation, are widely applied in the aerospace and biomedicine fields. However, traditional fixed calibration points fail to adapt to complex operational requirements and exhibit problems including a limited coverage range and low efficiency. To address these challenges, this study develops a Gaussian Process-based Multi-Fidelity Bayesian Optimization (GP-MFBO) framework for optimal selection of temperature and humidity calibration points. The framework integrates the following three key components: (1) a three-layer progressive multi-fidelity modeling system comprising physical analytical models, computational fluid dynamics (CFD) numerical simulations, and experimental verification; (2) a systematic uncertainty quantification system covering model uncertainty, parameter uncertainty, and observation uncertainty; and (3) an adaptive acquisition function that balances uncertainty penalty mechanisms and multi-fidelity information gain evaluation. The experimental results demonstrate that the proposed GP-MFBO method achieves optimal calibration point combinations with a temperature uniformity score of 0.149 and humidity uniformity score of 2.38, approaching theoretical optimal solutions within 4.5% and 3.6%, respectively. Compared to standard Gaussian process, Co-Kriging, two-stage optimization, polynomial regression, and traditional single-fidelity methods, GP-MFBO achieves uniformity score improvements of up to 81.7% and 76.3% for temperature and humidity, respectively. The prediction confidence interval coverage reaches 94.2%, outperforming all comparative methods. This research provides a rigorous theoretical foundation and technical solution for the scientific design and reliable operation of large-space temperature and humidity calibration systems.
- 10 July 2025
- Published by Springer Nature in National Academy Science Letters
- Vol. 49 (6) , 889-894
A Methodological Study on the Construction of Piezoelectric-Conductive Composite Nanofibers Based on Structural Design
- 10 July 2025
- Published by Springer Nature in National Academy Science Letters
- Vol. 49 (6) , 889-894
A Methodological Study on the Construction of Piezoelectric-Conductive Composite Nanofibers Based on Structural Design
- Open Access
Preparation and Performance Study of Dual-Network Photo-Curable Conductive Silk Fibroin Composite Hydrogel
The printing precision of hydrogels directly determines the mechanical and electrical performance of scaffolds. In this study, poly(3,4-ethylenedioxythiophene)-poly (styrenesulfonate) (PEDOT:PSS) was directly compounded with glycidyl methacrylate-modified silk fibroin (Sil-MA) through a one-pot method to increase the solid content of the printing ink, enhancing its mechanical, electrical, and printability properties. A dual-network photo-curable conductive silk fibroin composite hydrogel (CDMA) was successfully prepared. The results show that the introduction of PEDOT:PSS significantly improved the conductivity of the hydrogel. (The bandgap decreased from 2.36 eV to 1.125 eV, and the maximum conductivity reached 0.534 S/m.) It also enhanced the microscopic 3D network density and mechanical properties of the hydrogel (compressive modulus up to 192 kPa). Moreover, the hydrogel demonstrated good stability during cyclic stability testing, providing a new approach to developing materials capable of high-precision printing with stable electrical performance.
Open AccessPreparation and Performance Study of Dual-Network Photo-Curable Conductive Silk Fibroin Composite Hydrogel
The printing precision of hydrogels directly determines the mechanical and electrical performance of scaffolds. In this study, poly(3,4-ethylenedioxythiophene)-poly (styrenesulfonate) (PEDOT:PSS) was directly compounded with glycidyl methacrylate-modified silk fibroin (Sil-MA) through a one-pot method to increase the solid content of the printing ink, enhancing its mechanical, electrical, and printability properties. A dual-network photo-curable conductive silk fibroin composite hydrogel (CDMA) was successfully prepared. The results show that the introduction of PEDOT:PSS significantly improved the conductivity of the hydrogel. (The bandgap decreased from 2.36 eV to 1.125 eV, and the maximum conductivity reached 0.534 S/m.) It also enhanced the microscopic 3D network density and mechanical properties of the hydrogel (compressive modulus up to 192 kPa). Moreover, the hydrogel demonstrated good stability during cyclic stability testing, providing a new approach to developing materials capable of high-precision printing with stable electrical performance.
- 21 October 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (11) , 115022
Force-extension and longitudinal response of wormlike chains with single cross-link
Certain important biopolymers, such as actin filaments, are known to have cross-links at their interfaces, which significantly influence their mechanical properties. To explore these effects, the force-extension and longitudinal response of wormlike chains (WLCs) with a single cross-link under tension in two-dimension are examined using both analytical methods and Brownian dynamics simulations. The cross-link is modeled as a spring in the analytical method, and mode analysis is used to calculate the path integrals associated with the partition function. These theoretical results are then validated through Brownian dynamics simulations. Final results indicate that the simulation results are consistent with the theoretical predictions, particularly for situations involving large tensile force and short chain, which are prerequisites for the application of the weak bending approximation.
- 21 October 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (11) , 115022
Force-extension and longitudinal response of wormlike chains with single cross-link
Certain important biopolymers, such as actin filaments, are known to have cross-links at their interfaces, which significantly influence their mechanical properties. To explore these effects, the force-extension and longitudinal response of wormlike chains (WLCs) with a single cross-link under tension in two-dimension are examined using both analytical methods and Brownian dynamics simulations. The cross-link is modeled as a spring in the analytical method, and mode analysis is used to calculate the path integrals associated with the partition function. These theoretical results are then validated through Brownian dynamics simulations. Final results indicate that the simulation results are consistent with the theoretical predictions, particularly for situations involving large tensile force and short chain, which are prerequisites for the application of the weak bending approximation.
- Open Access
Preparation and Structure–Property Relationship Study of Piezoelectric–Conductive Composite Polymer Nanofiber Materials for Bone Tissue Engineering
This study aimed to develop Janus-, cross-network-, and coaxial-structured piezoelectric–conductive polymer nanofibers through electrospinning to mimic the piezoelectricity of bone and facilitate the conduction of electrical signals in bone tissue repair. These nanofibers were constructed using the piezoelectric polymer polyvinylidene fluoride, and the conductive fillers reduced graphene oxide and polypyrrole. The influence of structural features on the electroactivity of the fibers was also explored. The morphology and components of the various structural samples were characterized using SEM, TEM, and FTIR. The electroactivity of the materials was assessed with a quasi-static d33 meter and the four-probe method. The results revealed that the piezoelectric–conductive phases were successfully integrated. The Janus-structured nanofibers demonstrated the best electroactivity, with a piezoelectric constant d33 of 24.5 pC/N and conductivity of 6.78 × 10−2 S/m. The tensile tests and MIP measurements showed that all samples had porosity levels exceeding 70%. The tensile strength of the Janus and cross-network structures exceeded that of the periosteum (3–4 MPa), with average pore sizes of 1194.36 and 2264.46 nm, respectively. These properties indicated good mechanical performance, allowing material support while preventing fibroblast invasion. The CCK-8 and ALP tests indicated that the Janus-structured samples were biocompatible and significantly promoted the proliferation of MC3T3-E1 cells.
Open AccessPreparation and Structure–Property Relationship Study of Piezoelectric–Conductive Composite Polymer Nanofiber Materials for Bone Tissue Engineering
This study aimed to develop Janus-, cross-network-, and coaxial-structured piezoelectric–conductive polymer nanofibers through electrospinning to mimic the piezoelectricity of bone and facilitate the conduction of electrical signals in bone tissue repair. These nanofibers were constructed using the piezoelectric polymer polyvinylidene fluoride, and the conductive fillers reduced graphene oxide and polypyrrole. The influence of structural features on the electroactivity of the fibers was also explored. The morphology and components of the various structural samples were characterized using SEM, TEM, and FTIR. The electroactivity of the materials was assessed with a quasi-static d33 meter and the four-probe method. The results revealed that the piezoelectric–conductive phases were successfully integrated. The Janus-structured nanofibers demonstrated the best electroactivity, with a piezoelectric constant d33 of 24.5 pC/N and conductivity of 6.78 × 10−2 S/m. The tensile tests and MIP measurements showed that all samples had porosity levels exceeding 70%. The tensile strength of the Janus and cross-network structures exceeded that of the periosteum (3–4 MPa), with average pore sizes of 1194.36 and 2264.46 nm, respectively. These properties indicated good mechanical performance, allowing material support while preventing fibroblast invasion. The CCK-8 and ALP tests indicated that the Janus-structured samples were biocompatible and significantly promoted the proliferation of MC3T3-E1 cells.
- Open Access
- 1 February 2024
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 24 (1) , 27-35
Design of Calibration System for Multi-Channel Thermostatic Metal Bath
The use of the thermostatic metal bath is becoming more and more extensive and the requirements for its precision and reliability are also increasing. To meet the needs of the metal bath calibration, a 12-channel thermostatic metal bath temperature field calibration system based on a four-wire PT100 has been designed. The system design includes a front-end temperature measurement component, which consists of a four-wire PT100 and a thermostatic block, and a signal processing component, which consists of a bidirectional constant current source excitation unit, a signal conditioning unit and a high-precision acquisition unit. The STM32f407 is used as the main control chip, and the analog channel selector is used for 12-channel selection. The constant current source is used for signal excitation, the proportional method is used to measure the PT100 resistance, and an acquisition circuit with a high-precision 32-bit ADS1263 analog-to-digital converter is used to amplify, filter and convert the analog signal. After piecewise linear fitting and system calibration, the temperature measurement accuracy can reach 0.4 mK, which meets the calibration requirements of the thermostatic metal bath.
- 1 February 2024
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 24 (1) , 27-35
Open AccessDesign of Calibration System for Multi-Channel Thermostatic Metal Bath
The use of the thermostatic metal bath is becoming more and more extensive and the requirements for its precision and reliability are also increasing. To meet the needs of the metal bath calibration, a 12-channel thermostatic metal bath temperature field calibration system based on a four-wire PT100 has been designed. The system design includes a front-end temperature measurement component, which consists of a four-wire PT100 and a thermostatic block, and a signal processing component, which consists of a bidirectional constant current source excitation unit, a signal conditioning unit and a high-precision acquisition unit. The STM32f407 is used as the main control chip, and the analog channel selector is used for 12-channel selection. The constant current source is used for signal excitation, the proportional method is used to measure the PT100 resistance, and an acquisition circuit with a high-precision 32-bit ADS1263 analog-to-digital converter is used to amplify, filter and convert the analog signal. After piecewise linear fitting and system calibration, the temperature measurement accuracy can reach 0.4 mK, which meets the calibration requirements of the thermostatic metal bath.
- 10 January 2024
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 39 (2) , 237-241
Preparation of PVDF/PVA composite films with micropatterned structures on light-cured 3D printed molds for hydrophilic modification of PVDF
Polyvinylidene fluoride (PVDF) is widely used in biotechnology due to its excellent biocompatibility, high temperature and pressure resistance, and outstanding mechanical properties. However, the hydrophobic nature of PVDF surface hinders the attachment of biological proteins. In order to enhance the wettability of PVDF surfaces, this study prepared composite films by blending PVDF with polyvinyl alcohol (PVA), and micro-patterned structures were fabricated on the material surface using a mold-replication method based on digital light processing (DLP) photopolymerization printing technology. A series of characterization techniques including surface morphology analysis, chemical composition analysis, and wettability testing were employed. The surface morphology analysis results indicated that the method of using DLP photopolymerization technology to print mold replicas and create micro-patterned structures was indeed effective in creating micro-patterned structures on both PVDF and PVDF/PVA composite films. The chemical composition analysis showed that the spin-coating of PVDF powder material resulted in PVDF β-phase crystalline structure, which has a positive effect on cell growth. Furthermore, the introduction of hydrophilic groups was achieved by mixing PVDF with PVA. Wetting test results indicate that the incorporation of the hydrophilic material PVA and micro-patterned surfaces both contribute to the improved hydrophilicity of the material. The water contact angle of the micro-patterned PVDF/PVA composite film reached 30.8°, exhibiting excellent hydrophilic properties. This study achieved the optimization of PVDF surface properties through micro-patterned surface modification and material composition design, providing novel insights for the further development of PVDF materials in the field of biotechnology.
- 10 January 2024
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 39 (2) , 237-241
Preparation of PVDF/PVA composite films with micropatterned structures on light-cured 3D printed molds for hydrophilic modification of PVDF
Polyvinylidene fluoride (PVDF) is widely used in biotechnology due to its excellent biocompatibility, high temperature and pressure resistance, and outstanding mechanical properties. However, the hydrophobic nature of PVDF surface hinders the attachment of biological proteins. In order to enhance the wettability of PVDF surfaces, this study prepared composite films by blending PVDF with polyvinyl alcohol (PVA), and micro-patterned structures were fabricated on the material surface using a mold-replication method based on digital light processing (DLP) photopolymerization printing technology. A series of characterization techniques including surface morphology analysis, chemical composition analysis, and wettability testing were employed. The surface morphology analysis results indicated that the method of using DLP photopolymerization technology to print mold replicas and create micro-patterned structures was indeed effective in creating micro-patterned structures on both PVDF and PVDF/PVA composite films. The chemical composition analysis showed that the spin-coating of PVDF powder material resulted in PVDF β-phase crystalline structure, which has a positive effect on cell growth. Furthermore, the introduction of hydrophilic groups was achieved by mixing PVDF with PVA. Wetting test results indicate that the incorporation of the hydrophilic material PVA and micro-patterned surfaces both contribute to the improved hydrophilicity of the material. The water contact angle of the micro-patterned PVDF/PVA composite film reached 30.8°, exhibiting excellent hydrophilic properties. This study achieved the optimization of PVDF surface properties through micro-patterned surface modification and material composition design, providing novel insights for the further development of PVDF materials in the field of biotechnology.
- 27 September 2023
- Published by Springer Nature in Chinese Journal of Polymer Science
- Vol. 42 (3) , 407-416
Spherical Confinement Generates Entropic Force to Accelerate Polymer Chain Detachment
- 27 September 2023
- Published by Springer Nature in Chinese Journal of Polymer Science
- Vol. 42 (3) , 407-416
Spherical Confinement Generates Entropic Force to Accelerate Polymer Chain Detachment
- Open Access
Numerical Simulations of the Driving Process of a Wheeled Machine Tire on a Snow-Covered Road
Wheeled machines, such as agricultural tractors, snowplows, and wheeled mobile robots, usually work on icy or snow-covered roads. Therefore, it is very important to study the driving and slip resistance of the tires of these machines. In this paper, we investigate the driving behavior of tires on snow-covered terrain by means of numerical simulations. A high-fidelity snow-covered road model is established, and smoothed particle hydrodynamics (SPH) and the finite element method (FEM) are employed to account for the behaviors of the snow layers and the pavement, respectively. We use the node-to-surface algorithm for the contact interactions between the snow and the pavement. The SPH parameters for the snow are calibrated by means of a triaxial compression experiment. A simplified tire model is established as well, using the FEM, and the effectiveness of the model is demonstrated via comparisons with the experimental data in terms of stiffness. Finally, the tire driving performance on the snow-covered road is simulated, and the influence of the tire surface configuration, external load, inflation pressure, and snowpack compression on the tire traction behaviors is systematically investigated.
Open AccessNumerical Simulations of the Driving Process of a Wheeled Machine Tire on a Snow-Covered Road
Wheeled machines, such as agricultural tractors, snowplows, and wheeled mobile robots, usually work on icy or snow-covered roads. Therefore, it is very important to study the driving and slip resistance of the tires of these machines. In this paper, we investigate the driving behavior of tires on snow-covered terrain by means of numerical simulations. A high-fidelity snow-covered road model is established, and smoothed particle hydrodynamics (SPH) and the finite element method (FEM) are employed to account for the behaviors of the snow layers and the pavement, respectively. We use the node-to-surface algorithm for the contact interactions between the snow and the pavement. The SPH parameters for the snow are calibrated by means of a triaxial compression experiment. A simplified tire model is established as well, using the FEM, and the effectiveness of the model is demonstrated via comparisons with the experimental data in terms of stiffness. Finally, the tire driving performance on the snow-covered road is simulated, and the influence of the tire surface configuration, external load, inflation pressure, and snowpack compression on the tire traction behaviors is systematically investigated.
- Open Access
- 3 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6801
Applying Statistical Models to Optimize the Weld Bead Geometry in the Vertical Oscillation Arc Narrow Gap All-Position GMAW
Vertical oscillation arc welding for narrow gap gas metal arc welding (NG-GMAW) has a relatively simple structure, and it is widely used in all-position pipeline field welding. However, it has some shortcomings, such as incomplete fusion defects on the sidewall and interlayer. Aiming at resolving these shortcomings, a mathematical model is proposed to obtain appropriate welding parameters in different positions. In this model, the response surface methodology (RSM) based on the central composite design (CCD) was developed to study the interactions between welding parameters and the weld bead geometry. Then the analysis of variance (ANOVA) was used to evaluate the accuracy and significance of the proposed model. Finally, experiments were carried out in flat, vertical, and overhead positions to obtain the optimal parameters. The macroscopic metallography of the transversal section of the weld bead under the optimizing welding parameters showed that the weld beads were free of defects in the sidewall and interlayers.
- 3 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6801
Open AccessApplying Statistical Models to Optimize the Weld Bead Geometry in the Vertical Oscillation Arc Narrow Gap All-Position GMAW
Vertical oscillation arc welding for narrow gap gas metal arc welding (NG-GMAW) has a relatively simple structure, and it is widely used in all-position pipeline field welding. However, it has some shortcomings, such as incomplete fusion defects on the sidewall and interlayer. Aiming at resolving these shortcomings, a mathematical model is proposed to obtain appropriate welding parameters in different positions. In this model, the response surface methodology (RSM) based on the central composite design (CCD) was developed to study the interactions between welding parameters and the weld bead geometry. Then the analysis of variance (ANOVA) was used to evaluate the accuracy and significance of the proposed model. Finally, experiments were carried out in flat, vertical, and overhead positions to obtain the optimal parameters. The macroscopic metallography of the transversal section of the weld bead under the optimizing welding parameters showed that the weld beads were free of defects in the sidewall and interlayers.