Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Youxin Zhou has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Enhancing efficiency in CO 2 scroll compressors: A data-driven optimization approach incorporating clearance tolerance

    by Youxin Zhou, Bin Peng, Zhixiang Liao

    Traditional optimization of scroll compressors often focuses on geometric adjustments and overlooks the coupled effects of real-gas behavior and dynamic leakage, especially under the high-pressure conditions of CO 2 transcritical cycles. To address the computational challenges of high-dimensional collaborative optimization, this paper proposes an integrated optimization framework that combines physical modeling with data-driven approaches. The framework first constructs a thermodynamic model that couples transient leakage mechanisms with real-gas effects. On this basis, a neural network surrogate model is established to reduce computational load, and Sobol global sensitivity analysis based on response surfaces is employed to identify key design variables, thereby systematically overcoming the computational efficiency bottleneck in multi-parameter collaborative optimization. Under the high-pressure conditions of the CO 2 transcritical cycle, minute variations in clearances significantly influence leakage flow and overall efficiency. Consequently, this study treats radial and tangential clearances as active optimization variables and incorporates manufacturing tolerance perturbations into the optimization objectives. A multi-objective collaborative optimization of volumetric efficiency ( η v ), isentropic efficiency ( η s ), and robustness (R) is performed, where robustness is defined as performance degradation not exceeding 2% under ±5% manufacturing tolerance variations. The optimization results are ultimately synthesized into a piecewise functional design criterion. This criterion links manufacturing and assembly-controllable parameters (radial clearance, scroll wrap height, and rotational speed) to provide design rules for compressors operating across different speed ranges. The optimization results demonstrate that, while ensuring robustness greater than 0.95, the framework achieves average improvements of 9.56% in η v and 5.12% in η s .


  • Thermodynamics and performance analysis of a combined algebraic spiral CO2 scroll compressor

    by Zhixiang Liao, Bin Peng, Yubo Zhang, Youxin Zhou, Xiaoliang Yang, Jian Sun, Bingguo Zhu, Pengcheng Zhang


  • Open Access

    Research on High-Temperature Frictional Performance Optimization and Synergistic Effects of Phosphate-Based Composite Lubricating Coatings

    by Yong Ding, Shengjun Wang, Youxin Zhou, Hongmei Lv, Baoping Yang

    In high-temperature, high-pressure, and corrosive industrial environments, frictional wear of metallic components stands as a critical determinant governing the long-term operational reliability of mechanical systems. To address the challenge of traditional lubricating coating failure under a broad temperature range (−50 to 500 °C), this study developed a phosphate-based composite lubricating coating. Through air-spraying technology and orthogonal experimental optimization, the optimal formulation was determined as follows: binder/filler ratio = 6:4, 5% graphite, 15% MoS2, and 10% aluminum powder. Experimental results demonstrated that at 500 °C, the coating forms an Al–O–P cross-linked network structure, with MoS2 oxidation generating MoO3 and aluminum powder transforming into Al2O3, significantly enhancing density and oxidation resistance. Friction tests revealed that the composite coating achieves a friction coefficient as low as 0.12 at room temperature with a friction time of 260 min. At 500 °C, the friction coefficient stabilizes at 0.24, providing 40 min of effective protection. This technology not only resolves the high-temperature instability of traditional coatings but also ensures an environmentally friendly preparation process with no harmful emissions, offering a technical solution for the protection of high-temperature equipment such as thermal power plant boiler tubes and petrochemical reactors.


  • Dynamic model and characteristic analysis of a combined algebraic spiral scroll compressor

    by Zhixiang Liao, Bin Peng, Yubo Zhang, Xiaoliang Yang, Youxin Zhou, Pengcheng Zhang, Bingguo Zhu


  • Open Access

    Assessment of Optimal Operating Range and Case Verification of a Waste Heat Air-Source Heat Pump Water Heater Based on a Semiempirical Parametric Model

    by Youxin Zhou, Bin Peng, Bingguo Zhu

    Waste heat air-source heat pump water heater (WH-ASHPWH) systems have been widely used to provide water heating in buildings due to their advantages of high efficiency and low environmental impact. It is important to determine reasonable operating conditions for WH-ASHPWH systems to improve their heating efficiency, especially for systems using industrial waste heat. In this study, a semiempirical parametric model of a WH-ASHPWH system was established to simulate heating performance under different working conditions and determine the optimum operating range of the system. A new discrete model for a tube-in-tube condenser was also generated. Taking the equipment of a pharmaceutical factory as an example, the heat exchanger model was first calibrated; then, the global model was used to study the effects of different air-side and condenser-side waste heat conditions on the heating performance of the system. According to the simulation results, the coefficient of performance (COP) reached a maximum value of 4.5 under the optimum working conditions. The deviation between the COP simulation data and experimental values was less than 8.28%, and the simulation time was less than 8 min. These metrics indicate that the model is reasonable and efficient.


  • Open Access

    Phase field simulation of grain growth in Al2O3-based composite ceramic cutting tool materials containing second phase nanoparticles and pores

    by Youxin Zhou, Bin Peng

    A phase field model was established to simulate the grain growth of Al2O3-based composite ceramic tool materials containing second phase nanoparticles and pores. The free energy parameters of the model are directly related to the surface and grain boundary energies of Al2O3 such that the grain growth process can be quantitatively analysed. The model was used to investigate the effects of the volume fraction and size of second phase particles on grain growth in Al2O3 with a certain initial pore volume fraction. Findings show that pores and second phase particles jointly hinder grain growth. When the radii of second phase nanoparticles are the same, as the number of particles increase, most of the grain boundaries occur as straight lines in the microstructure, and grain size decreases. It is beneficial to obtain fine and uniform microstructure. However, when the particles content reaches a certain level, the second phase particles tend to agglomerate at the grain boundary of matrix grains, which will result in a decrease in the properties of nanocomposite ceramic tool materials. The study also found that, at a constant volume fraction of particles, with the decrease of particle radius, the grain size decreases. When the second phase particle size is reduced to 50 nm, relatively more intragranular microstructure was observed, which is considered to be the main reason for increasing the toughness of nano composite ceramic tool materials. Through analyzing the simulation results, the optimal combination of the content and size of the second phase particles can provide theoretical guidance for Al2O3 nano composite ceramic tool materials design and preparation.