Zuyao Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Zuyao Liu has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Yunqi Liu
Shanghai University
16 shared publications - Chengbo Mou
Shanghai University, Shanghai Institute for Advanced Communication and Data Science, Key Laboratory of Specialty Fiber Optics and Optical Access Networks, Joint International Research Laboratory of Specialty Fiber Optics and Advanced Communication, S
11 shared publications Chengbo Mou
6 shared publicationsXinyi Zhao
6 shared publications- Yunhe Zhao
Institute of Logistics Science and Engineering, Shanghai Maritime University, Shanghai 201306, China
6 shared publications - Xinyi Zhao
College of Electronic and Electrical Engineering, Henan Normal University, Xinxiang, China
5 shared publications
Latest Publications
- 8 September 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (18) , 5113-5116
Dual dispersion turning-points-enabled highly sensitive refractive index detection using tri-core fiber helical long-period gratings
This paper proposes a dual dispersion turning points (DTPs) enabled tri-core-fiber (TCF) helical long-period gratings (HLPGs) sensor, which is experimentally investigated for the first time, to the best of our knowledge. Numerical simulations and analysis show that dual DTP-related resonances can be generated within a single grating by optimizing the grating period and that the 2nd DTP-related resonance can be excited by increasing the surrounding RI. Subsequently, TCF-HLPGs samples were fabricated using a CO 2 laser and the RI sensing behaviors are experimentally investigated, confirming the realization of dual-DTPs, thereby enabling dual-region RI detection. The sensor achieves a maximum wavelength-separation sensitivity of 6653.9 nm/RIU and a transmission-contrast sensitivity of −139.1 dB/RIU, with a low temperature cross-sensitivity of 0.00017 RIU/°C. The proposed TCF-HLPGs can realize dual-DTPs-enhanced RI sensing within a single grating, providing a compact and reproducible structure for high-sensitivity and wide-range RI detection.
- 8 September 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (18) , 5113-5116
Dual dispersion turning-points-enabled highly sensitive refractive index detection using tri-core fiber helical long-period gratings
This paper proposes a dual dispersion turning points (DTPs) enabled tri-core-fiber (TCF) helical long-period gratings (HLPGs) sensor, which is experimentally investigated for the first time, to the best of our knowledge. Numerical simulations and analysis show that dual DTP-related resonances can be generated within a single grating by optimizing the grating period and that the 2nd DTP-related resonance can be excited by increasing the surrounding RI. Subsequently, TCF-HLPGs samples were fabricated using a CO 2 laser and the RI sensing behaviors are experimentally investigated, confirming the realization of dual-DTPs, thereby enabling dual-region RI detection. The sensor achieves a maximum wavelength-separation sensitivity of 6653.9 nm/RIU and a transmission-contrast sensitivity of −139.1 dB/RIU, with a low temperature cross-sensitivity of 0.00017 RIU/°C. The proposed TCF-HLPGs can realize dual-DTPs-enhanced RI sensing within a single grating, providing a compact and reproducible structure for high-sensitivity and wide-range RI detection.
- 7 February 2026
- Published by Elsevier in Infrared Physics & Technology
- Vol. 155
Torsion-insensitive long-period fiber gratings via pre-twist assisted CO2 laser inscription
- 7 February 2026
- Published by Elsevier in Infrared Physics & Technology
- Vol. 155
Torsion-insensitive long-period fiber gratings via pre-twist assisted CO2 laser inscription
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 19250-19257
Torsion-Insensitive Curvature Sensing via Azimuthal-Order-Controlled Cladding Mode Coupling in Long-Period Fiber Gratings
We proposed a novel long-period fiber grating (LPFG) capable of simultaneously coupling cladding modes with different azimuthal orders. A theoretical model of an LPFG with asymmetric refractive index modulation (RIM) was developed in a single-mode fiber to investigate the effects of cross-sectional distribution and modulation depth on the coupling efficiency of cladding modes. Unlike conventional fabrication methods, a novel CO2 laser-based point-shaped exposure technique was introduced to induce asymmetric RIM, enabling the simultaneous coupling of the LP15 and LP06 mode within a single grating. The proposed LPFG leverages the resonance wavelength difference between the two cladding modes for sensing applications. Experimental results demonstrated effective suppression of torsion sensitivity, achieving a minimal value of 1.2 pm/(rad/m) over a twist rate range of –34.5 rad/m to 34.5 rad/m. Additionally, the LPFG reduced sensitivity to temperature and refractive index while exhibiting a high curvature sensitivity of 13.34 nm/m-1 over a curvature range of 0 to 3.88 m-1. The combination of reduced cross-sensitivities, high curvature sensitivity, and compact structure highlights the potential of the proposed LPFG for practical sensing applications in complex environments.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 19250-19257
Torsion-Insensitive Curvature Sensing via Azimuthal-Order-Controlled Cladding Mode Coupling in Long-Period Fiber Gratings
We proposed a novel long-period fiber grating (LPFG) capable of simultaneously coupling cladding modes with different azimuthal orders. A theoretical model of an LPFG with asymmetric refractive index modulation (RIM) was developed in a single-mode fiber to investigate the effects of cross-sectional distribution and modulation depth on the coupling efficiency of cladding modes. Unlike conventional fabrication methods, a novel CO2 laser-based point-shaped exposure technique was introduced to induce asymmetric RIM, enabling the simultaneous coupling of the LP15 and LP06 mode within a single grating. The proposed LPFG leverages the resonance wavelength difference between the two cladding modes for sensing applications. Experimental results demonstrated effective suppression of torsion sensitivity, achieving a minimal value of 1.2 pm/(rad/m) over a twist rate range of –34.5 rad/m to 34.5 rad/m. Additionally, the LPFG reduced sensitivity to temperature and refractive index while exhibiting a high curvature sensitivity of 13.34 nm/m-1 over a curvature range of 0 to 3.88 m-1. The combination of reduced cross-sensitivities, high curvature sensitivity, and compact structure highlights the potential of the proposed LPFG for practical sensing applications in complex environments.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (23) , 8449-8455
Near 400 nm Broadband Mode Converter Based on Cascaded Long Period Fiber Gratings
We demonstrated the ultra-broadband mode converters using cascaded long-period fiber gratings (c-LPFGs), which possess a maximum bandwidth of near 400 nm. The design and fabrication of c-LPFGs are fully investigated, exploring various period combinations and utilizing CO2 laser irradiated on specialty few mode fibers near the dispersion turning point. Theoretical simulations and experimental results demonstrate the efficiency of c-LPFGs in exciting ultra-broadband LP11 core modes and first order orbital angular momentum mode. The achieved experimental 10-dB bandwidth of 395.8 nm highlights broadband mode conversion capabilities. Additionally, the 10-dB bandwidth of the gratings reveals tunability through twist rate adjustments, providing a further enhancement of 13.7 nm with a twist rate of 36 rad/m. The proposed c-LPFGs showcase potential for practical applications in optical communication systems, making significant contributions to ultra-broadband high-order mode generation.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (23) , 8449-8455
Near 400 nm Broadband Mode Converter Based on Cascaded Long Period Fiber Gratings
We demonstrated the ultra-broadband mode converters using cascaded long-period fiber gratings (c-LPFGs), which possess a maximum bandwidth of near 400 nm. The design and fabrication of c-LPFGs are fully investigated, exploring various period combinations and utilizing CO2 laser irradiated on specialty few mode fibers near the dispersion turning point. Theoretical simulations and experimental results demonstrate the efficiency of c-LPFGs in exciting ultra-broadband LP11 core modes and first order orbital angular momentum mode. The achieved experimental 10-dB bandwidth of 395.8 nm highlights broadband mode conversion capabilities. Additionally, the 10-dB bandwidth of the gratings reveals tunability through twist rate adjustments, providing a further enhancement of 13.7 nm with a twist rate of 36 rad/m. The proposed c-LPFGs showcase potential for practical applications in optical communication systems, making significant contributions to ultra-broadband high-order mode generation.
- 21 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (14) , 4980-4986
Bandwidth Tunable Ultra-Broadband OAM Generators Based on Chirped Long Period Fiber Gratings at Dispersion Turning Point
We demonstrated the fabrication of bandwidth tunable ultra-broadband mode converters based on chirped long period fiber grating (C-LPFG) and tilted chirped LPFG (TC-LPFG) in a two-mode fiber (TMF) by a CO 2 laser. The proposed mode converters based on C-LPFG and TC-LPFG experimentally realized mode conversion from the fundamental mode (LP 01 mode) to LP 11 mode and ±1 st order orbital angular momentum with a 10-dB bandwidth of 409.1 nm and 405.3 nm, respectively. The maximum tunable range of 10-dB bandwidth the proposed TC-LPFG is 50 nm, which is twice wider than that of the C-LPFG, while maintaining the same twist rate ranging from -36 rad/m ∼36 rad/m applied on the gratings. Consequently, the 10-dB bandwidth of the TC-LPFG can cover the O + E + S + C + L bands, which excellently optimize the bandwidth tunable range. The proposed bandwidth tunable ultra-broadband mode converters hold great potential for applications in mode division multiplexing transmission systems and optical fiber sensing systems based on few-mode fibers.
- 21 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (14) , 4980-4986
Bandwidth Tunable Ultra-Broadband OAM Generators Based on Chirped Long Period Fiber Gratings at Dispersion Turning Point
We demonstrated the fabrication of bandwidth tunable ultra-broadband mode converters based on chirped long period fiber grating (C-LPFG) and tilted chirped LPFG (TC-LPFG) in a two-mode fiber (TMF) by a CO 2 laser. The proposed mode converters based on C-LPFG and TC-LPFG experimentally realized mode conversion from the fundamental mode (LP 01 mode) to LP 11 mode and ±1 st order orbital angular momentum with a 10-dB bandwidth of 409.1 nm and 405.3 nm, respectively. The maximum tunable range of 10-dB bandwidth the proposed TC-LPFG is 50 nm, which is twice wider than that of the C-LPFG, while maintaining the same twist rate ranging from -36 rad/m ∼36 rad/m applied on the gratings. Consequently, the 10-dB bandwidth of the TC-LPFG can cover the O + E + S + C + L bands, which excellently optimize the bandwidth tunable range. The proposed bandwidth tunable ultra-broadband mode converters hold great potential for applications in mode division multiplexing transmission systems and optical fiber sensing systems based on few-mode fibers.
- 23 October 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (23) , 37426-37436
Broadband linearly polarized mode converter based on over-coupled long-period fiber grating
We demonstrate the fabrication of over-coupled long-period fiber gratings (LPFGs) in the 1.55-µm and 2-µm wavebands enabling broadband linearly polarized LP11 mode conversion using a CO2 laser. The birefringence of the fiber is caused by on one side laser exposure and increases with the increase of refractive index modulation depth, which realizes the conversion of linearly polarized modes. The mode conversion bandwidth can be significantly increased by using the over-coupled LPFG. The 10-dB bandwidth of the LPFGs with |κ|L values of π/2, 3π/2, and 5π/2 are 33.04, 80.84, and 114.08 nm at 1.55 µm waveband, respectively. The maximum bandwidth of the over-coupled LPFG is 3.79 times higher than that of conventional LPFG. The operating wavelength of the mode converter can be extended to 2.0 µm wavebands and the maximum 10-dB bandwidth reaches 161.32 nm. The proposed broadband linearly polarized mode converters could have potential application in the fields of mode division multiplexing systems, fiber laser systems.
- 23 October 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (23) , 37426-37436
Broadband linearly polarized mode converter based on over-coupled long-period fiber grating
We demonstrate the fabrication of over-coupled long-period fiber gratings (LPFGs) in the 1.55-µm and 2-µm wavebands enabling broadband linearly polarized LP11 mode conversion using a CO2 laser. The birefringence of the fiber is caused by on one side laser exposure and increases with the increase of refractive index modulation depth, which realizes the conversion of linearly polarized modes. The mode conversion bandwidth can be significantly increased by using the over-coupled LPFG. The 10-dB bandwidth of the LPFGs with |κ|L values of π/2, 3π/2, and 5π/2 are 33.04, 80.84, and 114.08 nm at 1.55 µm waveband, respectively. The maximum bandwidth of the over-coupled LPFG is 3.79 times higher than that of conventional LPFG. The operating wavelength of the mode converter can be extended to 2.0 µm wavebands and the maximum 10-dB bandwidth reaches 161.32 nm. The proposed broadband linearly polarized mode converters could have potential application in the fields of mode division multiplexing systems, fiber laser systems.
- 28 April 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (9) , 2461-2464
Ultrasensitive magnetic field sensor based on cladding-etched long-period grating
We demonstrate a high-sensitivity fiber-optic magnetic field sensor, which consists of a cladding-etched long-period fiber grating (LPFG) near the dispersion turning point (DTP) integrated with a magnetic fluid (MF). By reducing the cladding diameter of the LPFG, the fundamental mode is coupled to the lowest order cladding mode (LP0,2) near the DTP, which has a much higher surrounding refractive index sensitivity. Thanks to the excellent magneto-optical characteristics of the MF, the proposed sensor can achieve a magnetic field intensity sensitivity of 44.69 nm/mT in the range of 3–7.4 mT. The minimum magnetic field intensity that can be detected is 0.45 µT due to the 0.02-nm wavelength resolution of the optical spectrum analyzer. The proposed etched DTP-LPFG-based sensor with ultrahigh magnetic field sensitivity could have potential applications in magnetic fields and electrical systems.
- 28 April 2023
- Published by Optica Publishing Group in Optics Letters
- Vol. 48 (9) , 2461-2464
Ultrasensitive magnetic field sensor based on cladding-etched long-period grating
We demonstrate a high-sensitivity fiber-optic magnetic field sensor, which consists of a cladding-etched long-period fiber grating (LPFG) near the dispersion turning point (DTP) integrated with a magnetic fluid (MF). By reducing the cladding diameter of the LPFG, the fundamental mode is coupled to the lowest order cladding mode (LP0,2) near the DTP, which has a much higher surrounding refractive index sensitivity. Thanks to the excellent magneto-optical characteristics of the MF, the proposed sensor can achieve a magnetic field intensity sensitivity of 44.69 nm/mT in the range of 3–7.4 mT. The minimum magnetic field intensity that can be detected is 0.45 µT due to the 0.02-nm wavelength resolution of the optical spectrum analyzer. The proposed etched DTP-LPFG-based sensor with ultrahigh magnetic field sensitivity could have potential applications in magnetic fields and electrical systems.
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Micro-solder Fatigue Life Study Based on Crack Propagation Mechanism for High Reliability FC-CSP
As the size and pitch of flip chip solder joint reducing, and the thickness of the package reduce simultaneously, the solder thermal reliability become more and more critical. In this study, thermal cycling test (TCT) was performed for 3 groups of FC-CSP samples to get the crack initiation and propagation life. FE simulation had been used to get the increment of the solder strain energy density. Base on the experiment and simulation data, new empirical constants of Darveaux model were got for the FC-CSP system. With the modified Darveaux model, the influence of design parameters including packaging geometry size and material properties were compared for FC-CSP solder reliability. For the packaging geometry, substrate thickness should to be considered firstly to increasing the solder fatigue life, then is die thickness. The solder joint standoff showed little influence on the solder fatigue life. For the material properties, the Tg of MUF material should to be higher than high temperature of TCT, which is 150 °C in this study. CTE of MUF material showed the high influential on solder fatigue life. The followed influence rank are CTE of substrate and flexural modulus of MUF material, which have little difference in the influence on solder fatigue life.
- 10 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Micro-solder Fatigue Life Study Based on Crack Propagation Mechanism for High Reliability FC-CSP
As the size and pitch of flip chip solder joint reducing, and the thickness of the package reduce simultaneously, the solder thermal reliability become more and more critical. In this study, thermal cycling test (TCT) was performed for 3 groups of FC-CSP samples to get the crack initiation and propagation life. FE simulation had been used to get the increment of the solder strain energy density. Base on the experiment and simulation data, new empirical constants of Darveaux model were got for the FC-CSP system. With the modified Darveaux model, the influence of design parameters including packaging geometry size and material properties were compared for FC-CSP solder reliability. For the packaging geometry, substrate thickness should to be considered firstly to increasing the solder fatigue life, then is die thickness. The solder joint standoff showed little influence on the solder fatigue life. For the material properties, the Tg of MUF material should to be higher than high temperature of TCT, which is 150 °C in this study. CTE of MUF material showed the high influential on solder fatigue life. The followed influence rank are CTE of substrate and flexural modulus of MUF material, which have little difference in the influence on solder fatigue life.
- 14 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (3) , 855-862
Spectral and Sensing Performance of Long-Period Fiber Gratings at 2 μm Waveband
In this paper, we demonstrate the transmission spectral and surrounding refractive index (SRI) sensing performance of long-period fiber gratings (LPFGs) at 2 μm waveband. The cladding modes operating at 2 μm waveband show higher SRI sensitivity than 1.55 μm waveband. The influence of a little off resonance region of grating period, refractive index modulation and duty cycle of gratings are analyzed theoretically. Additionally, the LPFGs of LP08 mode near dispersion turning point operating at 2 μm waveband are investigated theoretically and experimentally. Mode splitting brings out with the increasing SRI. After the resonant dip splitting into two dips (dip A and dip A′), the SRI sensitivity of dip A are measured to be as high as −8495.2 nm/RIU in the SRI region of 1.445–1.457. The proposed 2-μm-waveband LPFGs makes it a potential in biochemical and environmental monitoring.
- 14 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 40 (3) , 855-862
Spectral and Sensing Performance of Long-Period Fiber Gratings at 2 μm Waveband
In this paper, we demonstrate the transmission spectral and surrounding refractive index (SRI) sensing performance of long-period fiber gratings (LPFGs) at 2 μm waveband. The cladding modes operating at 2 μm waveband show higher SRI sensitivity than 1.55 μm waveband. The influence of a little off resonance region of grating period, refractive index modulation and duty cycle of gratings are analyzed theoretically. Additionally, the LPFGs of LP08 mode near dispersion turning point operating at 2 μm waveband are investigated theoretically and experimentally. Mode splitting brings out with the increasing SRI. After the resonant dip splitting into two dips (dip A and dip A′), the SRI sensitivity of dip A are measured to be as high as −8495.2 nm/RIU in the SRI region of 1.445–1.457. The proposed 2-μm-waveband LPFGs makes it a potential in biochemical and environmental monitoring.
- 20 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (15) , 5134-5141
Tunable Broadband Mode Converter Based on Long-Period Fiber Gratings at 2-μm Waveband
We demonstrate the fabrication of a broadband mode converter (MC) operating at 2 μm waveband based on long-period fiber gratings (LPFGs) written in the two-mode fiber (TMF) by CO 2 laser. The proposed MC offers a 10-dB bandwidth of 58 nm, making it suitable for high-speed broad-band optical communication system at 2 μm waveband. The maximum conversion efficiency reaches 98.89% at wavelength of 2 μm. The torsion, strain, bending, and polarization characteristics of the broadband MC were measured experimentally. The torsion sensitivity of the LPFGs was measured to be 1.32 nm/(rad/m) at 2 μm waveband, which was almost three times higher than that of the grating with the same order mode coupling at 1.55 μm waveband. The proposed broadband MC can function as not only a promotion in fiber communication system but also a high sensitivity torsion sensor in fiber sensing system.
- 20 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (15) , 5134-5141
Tunable Broadband Mode Converter Based on Long-Period Fiber Gratings at 2-μm Waveband
We demonstrate the fabrication of a broadband mode converter (MC) operating at 2 μm waveband based on long-period fiber gratings (LPFGs) written in the two-mode fiber (TMF) by CO 2 laser. The proposed MC offers a 10-dB bandwidth of 58 nm, making it suitable for high-speed broad-band optical communication system at 2 μm waveband. The maximum conversion efficiency reaches 98.89% at wavelength of 2 μm. The torsion, strain, bending, and polarization characteristics of the broadband MC were measured experimentally. The torsion sensitivity of the LPFGs was measured to be 1.32 nm/(rad/m) at 2 μm waveband, which was almost three times higher than that of the grating with the same order mode coupling at 1.55 μm waveband. The proposed broadband MC can function as not only a promotion in fiber communication system but also a high sensitivity torsion sensor in fiber sensing system.