Don White
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Don White has a total of 124 co-authors. Here are the top co-authors by number of shared publications:
- Gilles Bellefleur
Geological Survey of Canada, 601 Booth St., Ottawa, ON, Canada
13 shared publications - Ernst Schetselaar
Natural Resources Canada
10 shared publications - Christine Rivard
Natural Resources Canada
6 shared publications - Honn Kao
Geological Survey of Canada, Natural Resources Canada (NRCan), Sidney, Canada
6 shared publications N Jacob
Natural Resources Canada
6 shared publicationsZ Hajnal
6 shared publications
Latest Publications
- 15 June 2026
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 91 (4) , P1-P10
Large-scale field test of surface-based DAS fiber loops for seismic imaging
Surface-based seismic field data were acquired through distributed acoustic sensing (DAS) measurements by using vertical loop configurations of a tight-buffered fiber-optic cable at the Aquistore CO2 storage site. A continuous run of the cable was buried in an 80-cm deep trench with vertical fiber loops attached to acrylonitrile butadiene styrene pipes that were deployed in shallow, 3-m drillholes to record steep-angle P-wave reflections from more than 400 dynamite shots. The capabilities and potential of DAS fiber loops for surface-based seismic surveys in such an environment were evaluated. The DAS strain measurements were converted to particle velocity and compared to geophone data that were acquired concurrently; stacked sections were focused on the deeper P-wave reflections in the 0.7–2.0 s time window. Estimated average phase response showed that the fiber loop converted-velocity DAS data were approximately 160° phase-rotated compared to the geophone data. Furthermore, seismic-to-well tie results for the DAS fiber loop and the geophone data showed 66% and 78% correlation, respectively. The P-wave reflection imaging results demonstrate that the DAS fiber loops can provide a comparable alternative to the geophones in this case.
- 15 June 2026
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 91 (4) , P1-P10
Large-scale field test of surface-based DAS fiber loops for seismic imaging
Surface-based seismic field data were acquired through distributed acoustic sensing (DAS) measurements by using vertical loop configurations of a tight-buffered fiber-optic cable at the Aquistore CO2 storage site. A continuous run of the cable was buried in an 80-cm deep trench with vertical fiber loops attached to acrylonitrile butadiene styrene pipes that were deployed in shallow, 3-m drillholes to record steep-angle P-wave reflections from more than 400 dynamite shots. The capabilities and potential of DAS fiber loops for surface-based seismic surveys in such an environment were evaluated. The DAS strain measurements were converted to particle velocity and compared to geophone data that were acquired concurrently; stacked sections were focused on the deeper P-wave reflections in the 0.7–2.0 s time window. Estimated average phase response showed that the fiber loop converted-velocity DAS data were approximately 160° phase-rotated compared to the geophone data. Furthermore, seismic-to-well tie results for the DAS fiber loop and the geophone data showed 66% and 78% correlation, respectively. The P-wave reflection imaging results demonstrate that the DAS fiber loops can provide a comparable alternative to the geophones in this case.
- 1 January 2023
- Published by Natural Resources Canada/CMSS/Information Management
Initiating transformative geoscience practice at the Geological Survey of Canada: Canada in 3D
Application of 3D technologies to the wide range of Geosciences knowledge domains is well underway. These have been operationalized in workflows of the hydrocarbon sector for a half-century, and now in mining for over two decades. In Geosciences, algorithms, structured workflows and data integration strategies can support compelling Earth models, however challenges remain to meet the standards of geological plausibility required for most geoscientific studies. There is also missing links in the institutional information infrastructure supporting operational multi-scale 3D data and model development. Canada in 3D (C3D) is a vision and road map for transforming the Geological Survey of Canada's (GSC) work practice by leveraging emerging 3D technologies. Primarily the transformation from 2D geological mapping, to a well-structured 3D modelling practice that is both data-driven and knowledge-driven. It is tempting to imagine that advanced 3D computational methods, coupled with Artificial Intelligence and Big Data tools will automate the bulk of this process. To effectively apply these methods there is a need, however, for data to be in a well-organized, classified, georeferenced (3D) format embedded with key information, such as spatial-temporal relations, and earth process knowledge. Another key challenge for C3D is the relative infancy of 3D geoscience technologies for geological inference and 3D modelling using sparse and heterogeneous regional geoscience information, while preserving the insights and expertise of geoscientists maintaining scientific integrity of digital products. In most geological surveys, there remains considerable educational and operational challenges to achieve this balance of digital automation and expert knowledge. Emerging from the last two decades of research are more efficient workflows, transitioning from cumbersome, explicit (manual) to reproducible implicit semi-automated methods. They are characterized by integrated and iterative, forward and reverse geophysical modelling, coupled with stratigraphic and structural approaches. The full impact of research and development with these 3D tools, geophysical-geological integration and simulation approaches is perhaps unpredictable, but the expectation is that they will produce predictive, instructive models of Canada's geology that will be used to educate, prioritize and influence sustainable policy for stewarding our natural resources. On the horizon are 3D geological modelling methods spanning the gulf between local and frontier or green-fields, as well as deep crustal characterization. These are key components of mineral systems understanding, integrated and coupled hydrological modelling and energy transition applications, e.g. carbon sequestration, in-situ hydrogen mining, and geothermal exploration. Presented are some case study examples at a range of scales from our efforts in C3D.
- 1 January 2023
- Published by Natural Resources Canada/CMSS/Information Management
Initiating transformative geoscience practice at the Geological Survey of Canada: Canada in 3D
Application of 3D technologies to the wide range of Geosciences knowledge domains is well underway. These have been operationalized in workflows of the hydrocarbon sector for a half-century, and now in mining for over two decades. In Geosciences, algorithms, structured workflows and data integration strategies can support compelling Earth models, however challenges remain to meet the standards of geological plausibility required for most geoscientific studies. There is also missing links in the institutional information infrastructure supporting operational multi-scale 3D data and model development. Canada in 3D (C3D) is a vision and road map for transforming the Geological Survey of Canada's (GSC) work practice by leveraging emerging 3D technologies. Primarily the transformation from 2D geological mapping, to a well-structured 3D modelling practice that is both data-driven and knowledge-driven. It is tempting to imagine that advanced 3D computational methods, coupled with Artificial Intelligence and Big Data tools will automate the bulk of this process. To effectively apply these methods there is a need, however, for data to be in a well-organized, classified, georeferenced (3D) format embedded with key information, such as spatial-temporal relations, and earth process knowledge. Another key challenge for C3D is the relative infancy of 3D geoscience technologies for geological inference and 3D modelling using sparse and heterogeneous regional geoscience information, while preserving the insights and expertise of geoscientists maintaining scientific integrity of digital products. In most geological surveys, there remains considerable educational and operational challenges to achieve this balance of digital automation and expert knowledge. Emerging from the last two decades of research are more efficient workflows, transitioning from cumbersome, explicit (manual) to reproducible implicit semi-automated methods. They are characterized by integrated and iterative, forward and reverse geophysical modelling, coupled with stratigraphic and structural approaches. The full impact of research and development with these 3D tools, geophysical-geological integration and simulation approaches is perhaps unpredictable, but the expectation is that they will produce predictive, instructive models of Canada's geology that will be used to educate, prioritize and influence sustainable policy for stewarding our natural resources. On the horizon are 3D geological modelling methods spanning the gulf between local and frontier or green-fields, as well as deep crustal characterization. These are key components of mineral systems understanding, integrated and coupled hydrological modelling and energy transition applications, e.g. carbon sequestration, in-situ hydrogen mining, and geothermal exploration. Presented are some case study examples at a range of scales from our efforts in C3D.
- 7 March 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (2) , X5-X6
Reply to comments on “Imaging the Aquistore reservoir after 36 kilotonnes of CO2 injection using distributed acoustic sensing” (K. Harris, D. J. White, and C. Samson, 2017, G eophysics , 82 , no. 6, M81–M96) and “Initial 4D seismic results after CO2 injection start-up at the Aquistore storage site” (L. A. N. Roach, D. J. White, B. Roberts, and D. Angus, 2017, G eophysics , 82 , no. 3, B95–B107)
- 7 March 2022
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (2) , X5-X6
Reply to comments on “Imaging the Aquistore reservoir after 36 kilotonnes of CO2 injection using distributed acoustic sensing” (K. Harris, D. J. White, and C. Samson, 2017, G eophysics , 82 , no. 6, M81–M96) and “Initial 4D seismic results after CO2 injection start-up at the Aquistore storage site” (L. A. N. Roach, D. J. White, B. Roberts, and D. Angus, 2017, G eophysics , 82 , no. 3, B95–B107)
- 1 January 2022
- Published by Natural Resources Canada/CMSS/Information Management
Initiating transformative geoscience practice at the Geological Survey of Canada: Canada in 3D
Application of 3D technologies to the wide range of Geosciences knowledge domains is well underway. These have been operationalized in workflows of the hydrocarbon sector for a half-century, and now in mining for over two decades. In Geosciences, algorithms, structured workflows and data integration strategies can support compelling Earth models, however challenges remain to meet the standards of geological plausibility required for most geoscientific studies. There is also missing links in the institutional information infrastructure supporting operational multi-scale 3D data and model development. Canada in 3D (C3D) is a vision and road map for transforming the Geological Survey of Canada's (GSC) work practice by leveraging emerging 3D technologies. Primarily the transformation from 2D geological mapping, to a well-structured 3D modelling practice that is both data-driven and knowledge-driven. It is tempting to imagine that advanced 3D computational methods, coupled with Artificial Intelligence and Big Data tools will automate the bulk of this process. To effectively apply these methods there is a need, however, for data to be in a well-organized, classified, georeferenced (3D) format embedded with key information, such as spatial-temporal relations, and earth process knowledge. Another key challenge for C3D is the relative infancy of 3D geoscience technologies for geological inference and 3D modelling using sparse and heterogeneous regional geoscience information, while preserving the insights and expertise of geoscientists maintaining scientific integrity of digital products. In most geological surveys, there remains considerable educational and operational challenges to achieve this balance of digital automation and expert knowledge. Emerging from the last two decades of research are more efficient workflows, transitioning from cumbersome, explicit (manual) to reproducible implicit semi-automated methods. They are characterized by integrated and iterative, forward and reverse geophysical modelling, coupled with stratigraphic and structural approaches. The full impact of research and development with these 3D tools, geophysical-geological integration and simulation approaches is perhaps unpredictable, but the expectation is that they will produce predictive, instructive models of Canada's geology that will be used to educate, prioritize and influence sustainable policy for stewarding our natural resources. On the horizon are 3D geological modelling methods spanning the gulf between local and frontier or green-fields, as well as deep crustal characterization. These are key components of mineral systems understanding, integrated and coupled hydrological modelling and energy transition applications, e.g. carbon sequestration, in-situ hydrogen mining, and geothermal exploration. Presented are some case study examples at a range of scales from our efforts in C3D.
- 1 January 2022
- Published by Natural Resources Canada/CMSS/Information Management
Initiating transformative geoscience practice at the Geological Survey of Canada: Canada in 3D
Application of 3D technologies to the wide range of Geosciences knowledge domains is well underway. These have been operationalized in workflows of the hydrocarbon sector for a half-century, and now in mining for over two decades. In Geosciences, algorithms, structured workflows and data integration strategies can support compelling Earth models, however challenges remain to meet the standards of geological plausibility required for most geoscientific studies. There is also missing links in the institutional information infrastructure supporting operational multi-scale 3D data and model development. Canada in 3D (C3D) is a vision and road map for transforming the Geological Survey of Canada's (GSC) work practice by leveraging emerging 3D technologies. Primarily the transformation from 2D geological mapping, to a well-structured 3D modelling practice that is both data-driven and knowledge-driven. It is tempting to imagine that advanced 3D computational methods, coupled with Artificial Intelligence and Big Data tools will automate the bulk of this process. To effectively apply these methods there is a need, however, for data to be in a well-organized, classified, georeferenced (3D) format embedded with key information, such as spatial-temporal relations, and earth process knowledge. Another key challenge for C3D is the relative infancy of 3D geoscience technologies for geological inference and 3D modelling using sparse and heterogeneous regional geoscience information, while preserving the insights and expertise of geoscientists maintaining scientific integrity of digital products. In most geological surveys, there remains considerable educational and operational challenges to achieve this balance of digital automation and expert knowledge. Emerging from the last two decades of research are more efficient workflows, transitioning from cumbersome, explicit (manual) to reproducible implicit semi-automated methods. They are characterized by integrated and iterative, forward and reverse geophysical modelling, coupled with stratigraphic and structural approaches. The full impact of research and development with these 3D tools, geophysical-geological integration and simulation approaches is perhaps unpredictable, but the expectation is that they will produce predictive, instructive models of Canada's geology that will be used to educate, prioritize and influence sustainable policy for stewarding our natural resources. On the horizon are 3D geological modelling methods spanning the gulf between local and frontier or green-fields, as well as deep crustal characterization. These are key components of mineral systems understanding, integrated and coupled hydrological modelling and energy transition applications, e.g. carbon sequestration, in-situ hydrogen mining, and geothermal exploration. Presented are some case study examples at a range of scales from our efforts in C3D.
- 1 January 2022
- Published by Natural Resources Canada/CMSS/Information Management
3D regional scale modelling of the Flin Flon-Glennie Complex: preparatory data analysis and preliminary results, Manitoba and Saskatchewan
GEOSCAN supports the mission of Natural Resources Canada through the timely access to information.
- 1 January 2022
- Published by Natural Resources Canada/CMSS/Information Management
3D regional scale modelling of the Flin Flon-Glennie Complex: preparatory data analysis and preliminary results, Manitoba and Saskatchewan
GEOSCAN supports the mission of Natural Resources Canada through the timely access to information.
- 4 December 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (2) , P1-P14
Toward improved distributed acoustic sensing sensitivity for surface-based reflection seismics: Configuration tests at the Aquistore CO2 storage site
Alternative fiber configurations have been tested in an attempt to improve the sensitivity of surface-deployed distributed acoustic sensing (DAS) fiber cables for the purpose of recording steep-angle P-wave reflections. Four alternative fiber configurations were deployed at the Aquistore CO2 storage site to record 401 dynamite shots during a 3D vertical seismic profiling survey. The test cable comprised horizontal configurations (straight fiber, helixes, and asymmetric helixes) buried in a shallow trench and vertical configurations (straight fiber and helixes) deployed in 3.5 m drillholes. Evaluation focused on deep reflections with two-way traveltimes of 0.8–1.8 s. All of the alternative fiber configurations increased the sensitivity relative to the horizontal straight fiber. Sensitivity was highest for the vertical straight fiber configurations and the asymmetric helixes with sensitivity increases of more than 10 and 5 dB, respectively, and amplitude-variation-with-offset behavior similar to that of a vertical-component geophone for reflections with incidence angles of 0°–15° at the surface and 0°–34° at the reflector. Modeling of the DAS responses explains the general pattern of sensitivity variability among the different configurations, but it does not explain the large range of observed sensitivities.
- 4 December 2021
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 87 (2) , P1-P14
Toward improved distributed acoustic sensing sensitivity for surface-based reflection seismics: Configuration tests at the Aquistore CO2 storage site
Alternative fiber configurations have been tested in an attempt to improve the sensitivity of surface-deployed distributed acoustic sensing (DAS) fiber cables for the purpose of recording steep-angle P-wave reflections. Four alternative fiber configurations were deployed at the Aquistore CO2 storage site to record 401 dynamite shots during a 3D vertical seismic profiling survey. The test cable comprised horizontal configurations (straight fiber, helixes, and asymmetric helixes) buried in a shallow trench and vertical configurations (straight fiber and helixes) deployed in 3.5 m drillholes. Evaluation focused on deep reflections with two-way traveltimes of 0.8–1.8 s. All of the alternative fiber configurations increased the sensitivity relative to the horizontal straight fiber. Sensitivity was highest for the vertical straight fiber configurations and the asymmetric helixes with sensitivity increases of more than 10 and 5 dB, respectively, and amplitude-variation-with-offset behavior similar to that of a vertical-component geophone for reflections with incidence angles of 0°–15° at the surface and 0°–34° at the reflector. Modeling of the DAS responses explains the general pattern of sensitivity variability among the different configurations, but it does not explain the large range of observed sensitivities.
- 1 June 2021
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 40 (6) , 434-441
Borehole seismic methods for geologic CO2 storage monitoring
Borehole geophysical methods are a key component of subsurface monitoring of geologic CO2 storage sites because boreholes form a locus where geophysical measurements can be compared directly with the controlling geology. Borehole seismic methods, including intrawell, crosswell, and surface-to-borehole acquisition, are useful for site characterization, surface seismic calibration, 2D/3D time-lapse imaging, and microseismic monitoring. Here, we review the most common applications of borehole seismic methods in the context of storage monitoring and consider the role that detailed geophysical simulations can play in answering questions that arise when designing monitoring plans. Case study examples are included from the multitude of CO2 monitoring projects that have demonstrated the utility of borehole seismic methods for this purpose over the last 20 years.
- 1 June 2021
- Published by Society of Exploration Geophysicists in The Leading Edge
- Vol. 40 (6) , 434-441
Borehole seismic methods for geologic CO2 storage monitoring
Borehole geophysical methods are a key component of subsurface monitoring of geologic CO2 storage sites because boreholes form a locus where geophysical measurements can be compared directly with the controlling geology. Borehole seismic methods, including intrawell, crosswell, and surface-to-borehole acquisition, are useful for site characterization, surface seismic calibration, 2D/3D time-lapse imaging, and microseismic monitoring. Here, we review the most common applications of borehole seismic methods in the context of storage monitoring and consider the role that detailed geophysical simulations can play in answering questions that arise when designing monitoring plans. Case study examples are included from the multitude of CO2 monitoring projects that have demonstrated the utility of borehole seismic methods for this purpose over the last 20 years.
- 1 January 2021
- Published by Natural Resources Canada/CMSS/Information Management
Seismic imaging of porphyry deposits with distributed acoustic sensing of fibre-optic cables: a summary of results at the New Afton Cu-Au mine, British Columbia
GEOSCAN supports the mission of Natural Resources Canada through the timely access to information.
- 1 January 2021
- Published by Natural Resources Canada/CMSS/Information Management
Seismic imaging of porphyry deposits with distributed acoustic sensing of fibre-optic cables: a summary of results at the New Afton Cu-Au mine, British Columbia
GEOSCAN supports the mission of Natural Resources Canada through the timely access to information.