Jyoti D. Nadargi
Research Subjects
Jyoti D. Nadargi has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Digambar Y. Nadargi
Empa, Swiss Federal Laboratories for Materials Science and Technology
2 shared publications - Mohaseen S. Tamboli
Korea Institute of Energy Technology (KENTECH), Naju, Republic of Korea
2 shared publications - Sharad S. Suryavanshi
School of Physical Sciences, P. A. H. Solapur University, Solapur, India
2 shared publications Abhijeet P. Patil
School of Physical Sciences, Punyashlok Ahilyadevi Holkar Solapur University, Solapur, India
1 shared publication- Ahmad Umar
Department of Chemistry, Faculty of Science and Arts, Najran University, Najran, Kingdom of Saudi Arabia
1 shared publication Hamid Shaikh
SABIC Polymer Research Centre, Department of Chemical Engineering, King Saud University, Riyadh, Saudi Arabia
1 shared publication
Latest Publications
- 31 January 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (4) , 1-15
Reduced graphene oxide/tungsten oxide (rGO/WO3): A versatile nanocomposite for enhanced detection of acetone
- 31 January 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (4) , 1-15
Reduced graphene oxide/tungsten oxide (rGO/WO3): A versatile nanocomposite for enhanced detection of acetone
- 14 April 2023
- Published by Springer Nature in Silicon
- Vol. 15 (13) , 5547-5553
A Novel Approach of Developing AgI Loaded Silica Aerogels for Possible Application as Cloud Seeding Material
- 14 April 2023
- Published by Springer Nature in Silicon
- Vol. 15 (13) , 5547-5553
A Novel Approach of Developing AgI Loaded Silica Aerogels for Possible Application as Cloud Seeding Material
- Open Access
- 9 September 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (9) , 361
Spinel Magnesium Ferrite (MgFe2O4): A Glycine-Assisted Colloidal Combustion and Its Potentiality in Gas-Sensing Application
Herein, we describe the facile synthesis of spinel MgFe2O4 ferrite and its potential use as a gas sensor using a straightforward and reliable sol–gel approach, i.e., the glycine-assisted auto-combustion route. The novelty in obtaining the sensing material via the auto-combustion route is its inherent simplicity and capability to produce the material at an industry scale. The said cost-effective process makes use of simple metal salts (Mg and Fe-nitrates) and glycine in an aqueous solution, which leads to the formation of spinel MgFe2O4 ferrite. A single-phase crystallinity with crystallite sizes ranging between 36 and 41 nm was observed for the synthesized materials using the X-ray diffraction (XRD) technique. The porous morphologies of the synthesized materials caused by auto-ignition during the combustion process were validated by the microscopic investigations. The EDS analysis confirmed the constituted elements such as Mg, Fe, and O, without any impurity peaks. The gas-sensing ability of the synthesized ferrites was examined to detect various reducing gases such as LPG, ethanol, acetone, and ammonia. The ferrite showed the highest response (>80%) toward LPG with the response and recovery times of 15 s and 23 s, respectively. Though the sensor responded low toward ammonia (~30%), its response and recovery times were very quick, i.e., 7 s and 9 s, respectively. The present investigation revealed that the synthesized ferrite materials are good candidates for fabricating high-performance sensors for reducing gases in real-world applications.
- 9 September 2022
- Published by MDPI AG in Chemosensors
- Vol. 10 (9) , 361
Open AccessSpinel Magnesium Ferrite (MgFe2O4): A Glycine-Assisted Colloidal Combustion and Its Potentiality in Gas-Sensing Application
Herein, we describe the facile synthesis of spinel MgFe2O4 ferrite and its potential use as a gas sensor using a straightforward and reliable sol–gel approach, i.e., the glycine-assisted auto-combustion route. The novelty in obtaining the sensing material via the auto-combustion route is its inherent simplicity and capability to produce the material at an industry scale. The said cost-effective process makes use of simple metal salts (Mg and Fe-nitrates) and glycine in an aqueous solution, which leads to the formation of spinel MgFe2O4 ferrite. A single-phase crystallinity with crystallite sizes ranging between 36 and 41 nm was observed for the synthesized materials using the X-ray diffraction (XRD) technique. The porous morphologies of the synthesized materials caused by auto-ignition during the combustion process were validated by the microscopic investigations. The EDS analysis confirmed the constituted elements such as Mg, Fe, and O, without any impurity peaks. The gas-sensing ability of the synthesized ferrites was examined to detect various reducing gases such as LPG, ethanol, acetone, and ammonia. The ferrite showed the highest response (>80%) toward LPG with the response and recovery times of 15 s and 23 s, respectively. Though the sensor responded low toward ammonia (~30%), its response and recovery times were very quick, i.e., 7 s and 9 s, respectively. The present investigation revealed that the synthesized ferrite materials are good candidates for fabricating high-performance sensors for reducing gases in real-world applications.
- Open Access
Design, Development and Validation of a Portable Gas Sensor Module: A Facile Approach for Monitoring Greenhouse Gases
We report the unique design and prototype of a portable gas sensor module for monitoring greenhouse gases. The commercially available gas sensors (MQ-02, MQ-135, and TGS2602) were adopted in designing the module using Arduino Uno. Different locations in the city of Solapur, India (17.6599° N, 75.9064° E), were scanned for the usability of the developed prototype of the mobile gas sensor module. The choice of gas sensors in combination with Arduino Uno led to an excellent prototype for measuring the concentration of greenhouse gases, and therefore the wrong alarm for toxic gases. The prototype model and corresponding greenhouse gas concentrations (ppm) are described using an interplay of sensor design, software program, and greenhouse gases sites.
Open AccessDesign, Development and Validation of a Portable Gas Sensor Module: A Facile Approach for Monitoring Greenhouse Gases
We report the unique design and prototype of a portable gas sensor module for monitoring greenhouse gases. The commercially available gas sensors (MQ-02, MQ-135, and TGS2602) were adopted in designing the module using Arduino Uno. Different locations in the city of Solapur, India (17.6599° N, 75.9064° E), were scanned for the usability of the developed prototype of the mobile gas sensor module. The choice of gas sensors in combination with Arduino Uno led to an excellent prototype for measuring the concentration of greenhouse gases, and therefore the wrong alarm for toxic gases. The prototype model and corresponding greenhouse gas concentrations (ppm) are described using an interplay of sensor design, software program, and greenhouse gases sites.