Helmut Woschitz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Helmut Woschitz has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Hansbert Heister
Universität der Bundeswehr München
3 shared publications- Boštjan Pulko
University of Ljubljana
1 shared publication Carla Fabris
Project Assistant, Institute of Soil Mechanics, Foundation Engineering and Computational Geotechnics, Graz Univ. of Technology, Rechbauerstraße 12, Graz 8010, Austria
1 shared publication- Christoph Martin Monsberger
ACI Monitoring GmbH
1 shared publication Helmut F. Schweiger
Professor, Institute of Soil Mechanics, Foundation Engineering and Computational Geotechnics, Graz Univ. of Technology, Rechbauerstraße 12, Graz 8010, Austria
1 shared publication- Karlheinz Gutjahr
JOANNEUM RESEARCH Forschungsgesellschaft mbH, DIGITAL—Institute for Digital Technologies, Steyrergasse 17, 8010 Graz, Austria
1 shared publication
Latest Publications
- Open Access
- 16 June 2025
- Published by Copernicus GmbH in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
- Vol. XLVIII-1/W, 73-80
Calibration and Validation of Phase One Industrial Cameras
JOANNEUM RESEARCH has reviewed the geometric lab calibration workflow of Phase One A/S, investigating the calibration method from a theoretical point of view, but also by evaluation of an existing calibration project from their new lab in Denver, USA. In addition, two iXM-RS150F reference cameras (50mm and 150mm lens) have been calibrated in the measurement lab of the Institute of Engineering Geodesy and Measurement Systems (IGMS) at Technical University Graz, Austria and results have been compared with the Phase One calibration certificates. Although correctness and quality of the Phase One calibration workflow could be confirmed, small but significant differences exist and can only be explained using various hypothesis e.g. about the influence of different environmental conditions during calibration. As it is not possible from direct comparison to decide which parameter set is the better or even correct one, methods to validate a camera calibration in the lab have been investigated which exist e.g. for acceptance testing of 3D optical measurement systems. It was found that existing methods based on capturing dedicated test bodies using a dense photo network and comparing reconstructed 3D lengths with the calibrated ones cannot be easily transferred to aerial camera systems, especially for longer focal lengths. Therefore, a new lab validation approach has been developed and tested using more available geodetic level rods, LSM matching of the bar code and an algorithm to transfer the length measurement from the image to object space without need for standard 3D point reconstruction.
- 16 June 2025
- Published by Copernicus GmbH in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
- Vol. XLVIII-1/W, 73-80
Open AccessCalibration and Validation of Phase One Industrial Cameras
JOANNEUM RESEARCH has reviewed the geometric lab calibration workflow of Phase One A/S, investigating the calibration method from a theoretical point of view, but also by evaluation of an existing calibration project from their new lab in Denver, USA. In addition, two iXM-RS150F reference cameras (50mm and 150mm lens) have been calibrated in the measurement lab of the Institute of Engineering Geodesy and Measurement Systems (IGMS) at Technical University Graz, Austria and results have been compared with the Phase One calibration certificates. Although correctness and quality of the Phase One calibration workflow could be confirmed, small but significant differences exist and can only be explained using various hypothesis e.g. about the influence of different environmental conditions during calibration. As it is not possible from direct comparison to decide which parameter set is the better or even correct one, methods to validate a camera calibration in the lab have been investigated which exist e.g. for acceptance testing of 3D optical measurement systems. It was found that existing methods based on capturing dedicated test bodies using a dense photo network and comparing reconstructed 3D lengths with the calibrated ones cannot be easily transferred to aerial camera systems, especially for longer focal lengths. Therefore, a new lab validation approach has been developed and tested using more available geodetic level rods, LSM matching of the bar code and an algorithm to transfer the length measurement from the image to object space without need for standard 3D point reconstruction.
- Open Access
Laboratory Investigations of the Leica RTC360 Laser Scanner—Distance Measuring Performance
A Leica RTC360 laser scanner was investigated using a linear horizontal comparator system with four targets of different reflectance. Several thousand panorama scans were conducted along the 30 m long comparator, basically in 40 mm steps. For a selected target, more detailed investigations were carried out with a 2 mm step width for a 2 m wide section. The absolute offset between the scanner and the relative interferometer measurements was determined with a calibrated total station. The investigations revealed several systematic effects like an offset in the distance measurement of about 1.3 mm. Furthermore, sections with stochastic behavior as well as sections with pseudo-cyclic parts were observed, depending on the reflectance of the target. The deterministic sections showed curved and striped patterns with some discontinuities of about 2 mm at 20 m, resulting in a saw-tooth like pattern along the distances. Within all the experiments, the distance deviations were below the manufacturer specifications of the 3D point accuracy. However, it was demonstrated that the distance measurements had clear systematic components. In using these new findings, the specification of the measurement “noise” in the data sheet has to be seen as critical.
Open AccessLaboratory Investigations of the Leica RTC360 Laser Scanner—Distance Measuring Performance
A Leica RTC360 laser scanner was investigated using a linear horizontal comparator system with four targets of different reflectance. Several thousand panorama scans were conducted along the 30 m long comparator, basically in 40 mm steps. For a selected target, more detailed investigations were carried out with a 2 mm step width for a 2 m wide section. The absolute offset between the scanner and the relative interferometer measurements was determined with a calibrated total station. The investigations revealed several systematic effects like an offset in the distance measurement of about 1.3 mm. Furthermore, sections with stochastic behavior as well as sections with pseudo-cyclic parts were observed, depending on the reflectance of the target. The deterministic sections showed curved and striped patterns with some discontinuities of about 2 mm at 20 m, resulting in a saw-tooth like pattern along the distances. Within all the experiments, the distance deviations were below the manufacturer specifications of the 3D point accuracy. However, it was demonstrated that the distance measurements had clear systematic components. In using these new findings, the specification of the measurement “noise” in the data sheet has to be seen as critical.
- 1 February 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (2) , 04020163
Numerical Simulation of a Ground Anchor Pullout Test Monitored with Fiber Optic Sensors
This paper presents a comprehensive study of the load transfer mechanism of a soil anchor during pullout test. The anchor was monitored with fiber optic sensors installed along the tendon and embedded in the grout, which enabled continuous measurements of strains with a spatial resolution of about 10 mm. The measured strain profile along the tendon indicates that the load is not transferred from the tendon to the grout at the same rate along the fixed length. Crack development was verified by measured peaks along the longitudinal strain profile. The in situ measurements were compared with results from finite-element simulations contributing to the interpretation of the in situ results. The load–displacement curves and strain distributions obtained with the numerical simulations compare well with measurements. The constitutive model selected for the grout is capable of reproducing the crack development and the numerical simulations suggest that debonding occurred during the anchor pullout test.
- 1 February 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 147 (2) , 04020163
Numerical Simulation of a Ground Anchor Pullout Test Monitored with Fiber Optic Sensors
This paper presents a comprehensive study of the load transfer mechanism of a soil anchor during pullout test. The anchor was monitored with fiber optic sensors installed along the tendon and embedded in the grout, which enabled continuous measurements of strains with a spatial resolution of about 10 mm. The measured strain profile along the tendon indicates that the load is not transferred from the tendon to the grout at the same rate along the fixed length. Crack development was verified by measured peaks along the longitudinal strain profile. The in situ measurements were compared with results from finite-element simulations contributing to the interpretation of the in situ results. The load–displacement curves and strain distributions obtained with the numerical simulations compare well with measurements. The constitutive model selected for the grout is capable of reproducing the crack development and the numerical simulations suggest that debonding occurred during the anchor pullout test.
- 1 January 2017
- Published by Springer Nature
- p. 403-461
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 January 2017
- Published by Springer Nature
- p. 403-461
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 January 2016
- Published by Springer Nature
- p. 1-59
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 January 2016
- Published by Springer Nature
- p. 1-59
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 January 2016
- Published by Walter de Gruyter GmbH in Journal of Applied Geodesy
- Vol. 10 (1)
Deformation Measurement of a Driven Pile Using Distributed Fibre-optic Sensing
New developments in distributed fibre-optic sensing allow the measurement of strain with a very high precision of about 1 µm / m and a spatial resolution of 10 millimetres or even better. Thus, novel applications in several scientific fields may be realised, e. g. in structural monitoring or soil and rock mechanics. Especially due to the embedding capability of fibre-optic sensors, fibre-optic systems provide a valuable extension to classical geodetic measurement methods, which are limited to the surface in most cases.In this paper, we report about the application of an optical backscatter reflectometer for deformation measurements along a driven pile. In general, pile systems are used in civil engineering as an efficient and economic foundation of buildings and other structures. Especially the length of the piles is crucial for the final loading capacity. For optimization purposes, the interaction between the driven pile and the subsurface material is investigated using pile testing methods. In a field trial, we used a distributed fibre-optic sensing system for measuring the strain below the surface of an excavation pit in order to derive completely new information.Prior to the field trial, the fibre-optic sensor was investigated in the laboratory. In addition to the results of these lab studies, we briefly describe the critical process of field installation and show the most significant results from the field trial, where the pile was artificially loaded up to 800 kN. As far as we know, this is the first time that the strain is monitored along a driven pile with such a high spatial resolution.
- 1 January 2016
- Published by Walter de Gruyter GmbH in Journal of Applied Geodesy
- Vol. 10 (1)
Deformation Measurement of a Driven Pile Using Distributed Fibre-optic Sensing
New developments in distributed fibre-optic sensing allow the measurement of strain with a very high precision of about 1 µm / m and a spatial resolution of 10 millimetres or even better. Thus, novel applications in several scientific fields may be realised, e. g. in structural monitoring or soil and rock mechanics. Especially due to the embedding capability of fibre-optic sensors, fibre-optic systems provide a valuable extension to classical geodetic measurement methods, which are limited to the surface in most cases.In this paper, we report about the application of an optical backscatter reflectometer for deformation measurements along a driven pile. In general, pile systems are used in civil engineering as an efficient and economic foundation of buildings and other structures. Especially the length of the piles is crucial for the final loading capacity. For optimization purposes, the interaction between the driven pile and the subsurface material is investigated using pile testing methods. In a field trial, we used a distributed fibre-optic sensing system for measuring the strain below the surface of an excavation pit in order to derive completely new information.Prior to the field trial, the fibre-optic sensor was investigated in the laboratory. In addition to the results of these lab studies, we briefly describe the critical process of field installation and show the most significant results from the field trial, where the pile was artificially loaded up to 800 kN. As far as we know, this is the first time that the strain is monitored along a driven pile with such a high spatial resolution.
- 1 January 2015
- Published by Springer Nature
- p. 1-59
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 January 2015
- Published by Springer Nature
- p. 1-59
Überprüfung und Kalibrierung der Messmittel in der Geodäsie
- 1 October 2009
- Published by Walter de Gruyter GmbH in TM - Technisches Messen
- Vol. 76 (10) , 465-473
Test statischer Eigenschaften ausgewählter NeigungssensorenTest of Static Properties of a Variety Tiltmeters
Zusammenfassung: Im Bauwesen werden Neigungssensoren bei unterschiedlichsten Anwendungen eingesetzt. Neben statischen Anwendungen wie Überwachungsmessungen werden sie zunehmend bei kinematischen Vermessungsaufgaben, z. B. der Positionierung von Fertigteilen, eingesetzt. Eine Genauigkeit von 0,01° ist für viele Anwendungen ausreichend. Gewohnte Verfahren wie die Umschlagmessung sind aber oftmals nicht möglich, weshalb die Stabilität der Kenngrößen der Sensoren essenziell ist. In diesem Beitrag werden einfache Tests zur Überprüfung statischer Eigenschaften vorgestellt und Resultate von 11 ausgewählten Neigungssensoren zusammengefasst. Ein weiterer Beitrag beschäftigt sich mit der Bestimmung dynamischer Eigenschaften.
- 1 October 2009
- Published by Walter de Gruyter GmbH in TM - Technisches Messen
- Vol. 76 (10) , 465-473
Test statischer Eigenschaften ausgewählter NeigungssensorenTest of Static Properties of a Variety Tiltmeters
Zusammenfassung: Im Bauwesen werden Neigungssensoren bei unterschiedlichsten Anwendungen eingesetzt. Neben statischen Anwendungen wie Überwachungsmessungen werden sie zunehmend bei kinematischen Vermessungsaufgaben, z. B. der Positionierung von Fertigteilen, eingesetzt. Eine Genauigkeit von 0,01° ist für viele Anwendungen ausreichend. Gewohnte Verfahren wie die Umschlagmessung sind aber oftmals nicht möglich, weshalb die Stabilität der Kenngrößen der Sensoren essenziell ist. In diesem Beitrag werden einfache Tests zur Überprüfung statischer Eigenschaften vorgestellt und Resultate von 11 ausgewählten Neigungssensoren zusammengefasst. Ein weiterer Beitrag beschäftigt sich mit der Bestimmung dynamischer Eigenschaften.