He Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
He Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Changqing Jiang
University of Duisburg-Essen
1 shared publication - Chenlu Song
Marine Engineering Equipment
1 shared publication - Chenlu Song
Department of Civil Engineering, Zhejiang Ocean University, Zhoushan, Zhejiang, China
1 shared publication Katsumi Iwamoto
Department of Marine Electronics and Mechanical Engineering, Tokyo University of Marine Science and Technology, 2-1-6, Etchujima, Koto-ku, Tokyo 135-8533Japan
1 shared publication- Kentaro Tanaka
Tokyo University of Marine Science and Technology
1 shared publication - Mingjie Hong1 shared publication
Latest Publications
- Open Access
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Vortex-driven nanogenerators for marine energy harvesting and flow velocity sensing
With the growing focus on clean and sustainable energy, ocean currents have emerged as a promising source. Traditional hydraulic turbines perform poorly in low-velocity ocean currents, limiting efficient energy extraction. This study introduces a novel multi-grating triboelectric nanogenerator (MG-TENG) that harnesses vortex-induced vibrations for energy harvesting, particularly effective in low-velocity marine environments. Our device not only converts ocean current energy into electricity but also measures flow velocity, addressing two critical needs. Structural improvements to the MG-TENG have boosted its output power by 33.5 times over conventional designs, while durability tests confirm its reliability under sustained operation. A new double-cylinder configuration extends the range of measurable velocities from 0.3 to 0.65 m/s, enhancing the device's versatility. These findings suggest that MG-TENG could serve as both a power supply and a velocity sensor, presenting an innovative solution for energy harvesting in low-velocity ocean currents.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Open AccessVortex-driven nanogenerators for marine energy harvesting and flow velocity sensing
With the growing focus on clean and sustainable energy, ocean currents have emerged as a promising source. Traditional hydraulic turbines perform poorly in low-velocity ocean currents, limiting efficient energy extraction. This study introduces a novel multi-grating triboelectric nanogenerator (MG-TENG) that harnesses vortex-induced vibrations for energy harvesting, particularly effective in low-velocity marine environments. Our device not only converts ocean current energy into electricity but also measures flow velocity, addressing two critical needs. Structural improvements to the MG-TENG have boosted its output power by 33.5 times over conventional designs, while durability tests confirm its reliability under sustained operation. A new double-cylinder configuration extends the range of measurable velocities from 0.3 to 0.65 m/s, enhancing the device's versatility. These findings suggest that MG-TENG could serve as both a power supply and a velocity sensor, presenting an innovative solution for energy harvesting in low-velocity ocean currents.
- Open Access
- 11 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (20) , 9221
Application of Different Image Processing Methods for Measuring Rock Fracture Structures under Various Confining Stresses
Fractures within granite may become channels for fluid flow and have a significant impact on the safety of waste storage. However, internal aperture variation under coupled conditions are usually difficult to grasp, and the inevitable differences between the measured data and the real fracture structure will lead to erroneous permeability predictions. In this study, two different CT (Computed Tomography) image processing methods are adopted to grasp internal fractures. Several CT images are extracted from different positions of a rock sample under different confining stresses. Two critical factors, i.e., aperture and the contact area ratio value within a single granite fracture sample, are investigated. Results show that aperture difference occurs under these two image processing methods. The contact area ratio value under two image processing methods has less than 1% difference without confining stress. However, there is larger than ten times difference when the confining stress increases to 3.0 MPa. Moreover, the edge detection method has the capability to obtain a relatively accurate internal fracture structure when confining pressure is applied to the rock sample. The analysis results provide a better approach to understanding practical rock fracture variations under various conditions.
- 11 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (20) , 9221
Open AccessApplication of Different Image Processing Methods for Measuring Rock Fracture Structures under Various Confining Stresses
Fractures within granite may become channels for fluid flow and have a significant impact on the safety of waste storage. However, internal aperture variation under coupled conditions are usually difficult to grasp, and the inevitable differences between the measured data and the real fracture structure will lead to erroneous permeability predictions. In this study, two different CT (Computed Tomography) image processing methods are adopted to grasp internal fractures. Several CT images are extracted from different positions of a rock sample under different confining stresses. Two critical factors, i.e., aperture and the contact area ratio value within a single granite fracture sample, are investigated. Results show that aperture difference occurs under these two image processing methods. The contact area ratio value under two image processing methods has less than 1% difference without confining stress. However, there is larger than ten times difference when the confining stress increases to 3.0 MPa. Moreover, the edge detection method has the capability to obtain a relatively accurate internal fracture structure when confining pressure is applied to the rock sample. The analysis results provide a better approach to understanding practical rock fracture variations under various conditions.
- Open Access
- 23 November 2020
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 36 (48) , 14892-14898
Observation of Wetting Behavior with Ultralow Contact Angle by a Total Reflection and Interference Fringe Method
In order to study the wetting behavior of a liquid film on a surface with ultralow contact angle, the interference fringe method with oblique upward laser is developed. This method allows us to detect the position of contact line precisely and observe the surface profile of very thin film. The contact angle measurement is verified within from 0.007° to 3°. The wetting behavior of silicone oil droplet on a glass substrate is observed. The wetting process can be distinguished with three stages, such as advancing, stable ,and receding stage. In the stable stage, there are two angles near the contact line. And the two angles have opposite variations in trend. It can be seen that there are some reciprocating changes in the two angles and the thickness of the liquid film near the contact line during the stable stage, like the edge of the surf.
- 23 November 2020
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 36 (48) , 14892-14898
Open AccessObservation of Wetting Behavior with Ultralow Contact Angle by a Total Reflection and Interference Fringe Method
In order to study the wetting behavior of a liquid film on a surface with ultralow contact angle, the interference fringe method with oblique upward laser is developed. This method allows us to detect the position of contact line precisely and observe the surface profile of very thin film. The contact angle measurement is verified within from 0.007° to 3°. The wetting behavior of silicone oil droplet on a glass substrate is observed. The wetting process can be distinguished with three stages, such as advancing, stable ,and receding stage. In the stable stage, there are two angles near the contact line. And the two angles have opposite variations in trend. It can be seen that there are some reciprocating changes in the two angles and the thickness of the liquid film near the contact line during the stable stage, like the edge of the surf.