Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sandra Tarancón has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Anisotropy and Defect Tolerance of FFF-Manufactured PETG: A Combined Tensile, Compressive and Mode I Fracture Study

    by Joseba K. Azcaray, Daniel Gomez-Lendinez, Sandra Tarancón, Elena Tejado, Matías Braun

    Fused filament fabrication (FFF) enables the rapid, low-cost manufacture of thermoplastic components, but its layer-by-layer deposition imparts a pronounced, orientation-dependent anisotropy that remains only partially characterised for polyethylene terephthalate glycol (PETG), a polymer whose fracture behaviour in particular has scarcely been reported. This work presents an integrated characterisation of unreinforced FFF PETG in which the tensile, compressive and mode I fracture response are measured within a single experimental campaign and under a common set of standards, so that the influence of build orientation can be resolved consistently across all three loading modes. Specimens were manufactured at two orientations, with the deposited filaments aligned with and transverse to the loading direction, and tested under quasi-static conditions. To move beyond the qualitative descriptions that dominate the literature, a dimensionless anisotropy index was defined for each property and used to compare the loading modes with one another and to benchmark PETG against reported values for polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). A distinctive anisotropy signature emerges: the tensile response is by far the most orientation-sensitive, the fracture response is markedly but more moderately anisotropic, and the compressive response is almost insensitive to build orientation. Although the transverse orientation loads the inter-layer bonds and fails in a brittle, low-energy manner, PETG retains a far larger fraction of its fracture resistance in this weak orientation than literature values reported for ABS, on this benchmark making it the apparently more forgiving material precisely in the property that governs the integrity of cracked or notched parts. Combining the measured strength and toughness within a linear-elastic fracture-mechanics framework further shows that build orientation governs the size of the intrinsic defect the material can sustain before unstable fracture, a defect-tolerance reading that neither property yields on its own, obtained under an idealised small-scale-yielding assumption whose applicability is examined explicitly for each orientation. These findings establish build orientation as a first-order design parameter for FFF PETG and provide a consistent, standard-based and cross-material reference dataset linking print orientation to the strength, stiffness, toughness and defect tolerance of the printed material.


  • EUROfusion characterisation programme of CuCrZr alloy for the EU DEMO divertor heat sink: mechanical and thermophysical properties

    by Aleksandr Zinovev, Marius Wirtz, Ermile Gaganidze, Salahudeen Mohamed, Nerea García-Rodríguez, David Cinger, Marco Lamberti, Andrea Moriani, Andrei Galatanu, Michael Pegritz, et al.

  • Open Access

    Synthesis and characterization at high temperature of colloidal processing cemented carbide and cermet

    by Sandra Tarancón Román

    The demanding working conditions of cutting tools, characterized by exposure to heat and abrasion, require materials with exceptional hardness, toughness, and wear resistance, which must be sustained at elevated temperatures. Cemented carbides, commonly known as hard metals, meet these requirements, making them the predominant choice for cutting tools and rock drilling applications. However, the rising demand for critical materials such as tungsten and cobalt has raised concerns about their supply and cost, prompting the exploration of alternative binders and processing methods. Although recycling of these cutting tools is vital to ensure sustainability and resource conservation, existing methods still remain inefficient and uneconomical in fully recovering materials. Consequently, the development of novel material systems is imperative to ensure industry continuity and sustainability. This research focuses on the formulation and evaluation of colloidal suspensions of cemented carbides (WC-FeNi) and cermets (Ti(C,N)-FeNi) with a Fe/Ni metallic binder composition of 85/15 wt%. These compositions aim to reduce the dependence on critical materials while enhancing the high-temperature performance of cutting tools. The materials were synthesized using water-based colloidal suspensions and their stability was confirmed via rheological analysis, enabling uniformly distributed spherical particles to be atomized. The sintering process was subsequently evaluated under various atmospheres (N2H2, high vacuum, and argon), to achieve a dense and hard material under a viable commercial route. These properties were satisfied by the argon atmosphere. Mechanical and thermal properties of the developed systems -including hardness, flexural strength, fracture toughness, wear resistance, and thermal diffusivity - were assessed up to 800 C temperature and compared to commercial cemented carbides. The WC-FeNi system exhibited mechanical properties comparable to those of the reference materials, with a strength improvement of up to 15 % at intermediate temperatures. Its high hardness, low wear rate, and temperature-dependent thermal conductivity make it a promising candidate for industrial applications. On the other hand, the Ti(C,N)-FeNi system, prepared with HPMC, exhibited inferior mechanical properties compared to PVA-based systems, with higher porosity leading to reduced hardness, flexural strength, and fracture toughness. Nonetheless, its thermal properties, including thermal conductivity and wear resistance at elevated temperatures, were notable, suggesting the need for further optimization to broaden its application scope. In summary, the results demonstrate that the WC-FeNi system, processed by a colloidal route, could be an excellent alternative to the Co-based. Its competitive mechanical and thermal properties, coupled with the environmental benefits of its composition and manufacturing process, position it as an attractive option for high-performance industrial applications. RESUMEN Las herramientas de corte están sometidas a condiciones de trabajo extremadamente exigentes, donde el calor y la abrasión son factores clave durante su operación. Estas circunstancias requieren materiales que combinen alta dureza, tenacidad de fractura y resistencia al desgaste, propiedades que deben mantenerse incluso a altas temperaturas, dado que son esenciales para garantizar la eficiencia, durabilidad y precisión en los procesos de corte. Los carburos cementados, también conocidos como metales duros, cumplen con estos requisitos, lo que los convierte en los materiales más utilizados para la fabricación de herramientas de corte y aplicaciones de perforación de rocas. Sin embargo, la creciente demanda de materiales críticos, como el wolframio y el cobalto, ha generado preocupación por su disponibilidad y el consiguiente aumento de precios, despertando el interés de la comunidad científica en desarrollar materiales y métodos de procesamiento alternativos. Aunque el reciclaje de las herramientas de corte es crucial para promover la sostenibilidad y conservar los recursos, los procesos actuales no logran aún recuperar todos los materiales de forma eficiente o económica. Por ello, es fundamental desarrollar nuevas composiciones que garanticen la continuidad y sostenibilidad de la industria. Esta investigación se centra en la fabricación y evaluación de suspensiones coloidales de carburos cementados (WC-FeNi) y cermets (Ti(C,N)-FeNi), en los cuales la composición del ligante metálico Fe/Ni fue fijada en un 85/15 % en peso, respectivamente. Estas composiciones fueron seleccionadas con el objetivo de desarrollar materiales alternativos que, no solo reduzcan el contenido de elementos críticos, sino que también mejoren el rendimiento de las herramientas de corte a alta temperatura. En la fabricación de los materiales se emplearon suspensiones coloidales de base agua, siendo su estabilidad evaluada a través de su comportamiento reológico, obteniendo una atomización adecuada de partículas esféricas y uniformemente distribuidas. Posteriormente, se estudió la sinterización de las muestras verdes en diferentes atmósferas (N2H2, vacío y argón), siendo esta última la más adecuada para obtener un material denso y de alta dureza, además de ser comercialmente viable. El análisis detallado de las propiedades mecánicas y térmicas de los materiales sinterizados incluyó la evaluación de la dureza, resistencia a la flexión, tenacidad de fractura, resistencia al desgaste y difusividad térmica en un rango de temperaturas desde ambiente hasta 800 C, comparándolos con sistemas comerciales de carburo cementado utilizados como referencia. El material WC-FeNi mostró propiedades mecánicas comparables a las del material...

  • Open Access

    Effects of Accelerating the Ageing of 1D PLA Filaments after Fused Filament Fabrication

    by Jaime Orellana-Barrasa, Sandra Tarancón, José Ygnacio Pastor

    The effects of post-treatment temperature-based methods for accelerating the ageing of PLA were studied on 1D single-PLA filaments after fused filament fabrication (FFF). The goal was to answer the questions whether the PLA can be safely aged—i.e., without degrading—at higher temperatures; at which temperatures, if any; how long it takes for the PLA to fully age at the chosen temperature; and which are the main differences between the material aged at room temperature and the material aged at higher temperatures. We also share other helpful information found. The use of 1D filaments allows for decoupling the variables related to the 3D structure (layer height, raster angle, infill density, and layers adhesion) from the variables solely related to the material (here, we analysed the molecular weight, the molecular orientation, and the crystallinity). 1D PLA filaments were aged at 20, 39, 42, 51, 65, 75, and 80 °C in a water-bath-inspired process in which the hydrolytic degradation of the PLA was minimised for the ageing temperatures of interest. Those temperatures were selected based on a differential scanning calorimetry (DSC) scan of the PLA right after it was printed in order to study the most effective ageing temperature, 39 °C, and highlight possible degradation mechanisms during ageing. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded and compared with those of the material aged at room temperature. A DSC scan was used to evaluate the thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation, and melting reactions were analysed. A double glass transition was found, and its potential implications for the scientific community are discussed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting, and the so-called summer effect—the stabilisation of properties at higher values when aged at higher temperatures—are discussed to assess the safety of accelerating the ageing rate and the differences between the materials aged at different temperatures. It was found that the PLA aged at 39 °C (1) reached almost stable properties with just one day of ageing, i.e., the ageing rate accelerated by 875% for the elastic modulus and by 1635% for the yield strength; (2) the stable properties were higher than those from the PLA aged at room temperature; and (3) no signs of degradation were identified for the ageing temperature of interest.


  • Open Access

    On the Mechanical Properties of Hybrid Dental Materials for CAD/CAM Restorations

    by Teresa Palacios, Sandra Tarancón, José Ygnacio Pastor

    Two hybrid dental materials available for computer-aided design and manufacturing (CAD/CAM) dental restorations have been selected to explore their potential. On the one hand, the scarcely investigated polymer-based material Vita Enamic® (VE) and, on the other hand, the leucite-based material IPS Empress® CAD (EC). Their micro-structure and mechanical performance were analyzed in two environments: directly as received by the manufacturer (AR), and after immersion and storage in artificial saliva (AS) for 30 days to determine the influence of the saliva effect. To avoid an inappropriate selection of materials for clinical use, a full understanding of their mechanical behavior is essential. Therefore, this investigation aims to determine the micro-structural and chemical composition by field emission scanning electron microscopy (FE-SEM) and X-ray fluorescence analysis, establishing the density, micro- and nano-hardness, the nano-elastic modulus, and the flexural strength and fracture toughness (by introducing a femto-laser notch to replicate a real crack). In addition, fracture surfaces of the broken samples were analyzed to correlate the failure micro-mechanisms with their mechanical properties. Results indicate that while the crystalline phase of the materials is very similar (composed of SiO2 and Al2O3), the micro-structure and mechanical behavior is not. The material EC, with finer micro-structure, exhibits a higher mechanical performance but with greater variability of results. Furthermore, the material VE, with a 25 vol.% polymer phase, shows a mechanical performance similar to enamel and dentin and therefore more similar to human behavior.


  • Open Access

    Saliva Influence on the Mechanical Properties of Advanced CAD/CAM Composites for Indirect Dental Restorations

    by Teresa Palacios, Sandra Tarancón, Cristian Abad, José Ygnacio Pastor

    This study aims to evaluate the microstructural and mechanical properties of three commercial resin-based materials available for computer-aid design and manufacturing (CAD/CAM)-processed indirect dental restoration: LavaTM Ultimate Restorative (LU), 3M ESPE; Brilliant Crios (BC), COLTENE and CerasmartTM (CS), GC Dental Product. The three types of resin-based composite CAD/CAM materials were physically and mechanically tested under two conditions: directly as received by the manufacturer (AR) and after storage under immersion in artificial saliva (AS) for 30 days. A global approximation to microstructure and mechanical behaviour was evaluated: density, hardness and nanohardness, nanoelastic modulus, flexural strength, fracture toughness, fracture surfaces, and microstructures and fractography. Moreover, their structural and chemical composition using X-ray fluorescence analysis (XRF) and field emission scanning electron microscopy (FESEM) were investigated. As a result, LU exhibited slightly higher mechanical properties, while the decrease of its mechanical performance after immersion in AS was doubled compared to BC and CS. Tests of pristine material showed 13 GPa elastic modulus, 150 MPa flexural strength, 1.0 MPa·m1/2 fracture toughness, and 1.0 GPa hardness for LU, 11.4 GPa elastic modulus; 140 MPa flexural strength, 1.1 MPa·m1/2 fracture toughness, and 0.8 GPa hardness for BC; and 8.3 GPa elastic modulus, 140 MPa flexural strength, 0.9 MPa·m1/2 fracture toughness, and 0.7 GPa hardness for CS. These values were significantly reduced after one month of immersion in saliva. The interpretation of the mechanical results could suggest, in general, a better behaviour of LU compared with the other two despite it having the coarsest microstructure of the three studied materials. The saliva effect in the three materials was critically relevant for clinical use and must be considered when choosing the best solution for the restoration to be used.


  • THE MORDAZITAS GAME - TEACHING STUDENTS THROUGH INSTAGRAM

    by Jaime Orellana Barrasa, Sandra Tarancón Román, Elena Tejado Garrido, José Ygnacio Pastor Caño

  • DISCOVERING THE MURDERER: A SUCCESSFUL SHERLOCK HOLMES GAMIFICATION PROJECT

    by Sandra Tarancón Román, Jaime Orellana Barrasa, Elena Tejado Garrido, José Ygnacio Pastor Caño

    Information about the paper titled "DISCOVERING THE MURDERER: A SUCCESSFUL SHERLOCK HOLMES GAMIFICATION PROJECT" at IATED Digital Library

  • Beneficial effects of a WC addition in FAST-densified tungsten

    by Saša Novak, Matej Kocen, Andreja Šestan Zavašnik, Andrei Galatanu, Magdalena Galatanu, Sandra Tarancón, Elena Tejado, Jose Ygnacio Pastor, Petra Jenuš