Sudirja Sudirja
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sudirja Sudirja has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Christantho Budiman
Research Center for Transportation Technology, National Research and Innovation Agency, South Tangerang 15314, Indonesia
5 shared publications - Sunarto Kaleg
National Research and Innovation Agency, Indonesia
5 shared publications - Aam Muharam
National Research and Innovation Agency, Indonesia
4 shared publications - Amin Amin
Research Center of Transportation Technology, National Research and Innovation agency, West Java, Indonesia
4 shared publications - Abdul Hapid
Research Center of Transportation Technology, National Research and Innovation agency,West Java,Indonesia
3 shared publications - Rina Mardiati
UIN Sunan Gunung Djati Bandung
3 shared publications
Latest Publications
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase Gate Switch Control of BLDC Motor Driver for Power Transfer Efficiency
This paper examines the power transfer efficiency of three-phase gate switches to drive BLDC motors. The three-phase gate switch has six gate switches with eight switch states, which are used to control voltage or current. The effect of voltage arising on connection lines between gate switches can be determined by taking into account the rise time, fall time, and propagation delay parameters. Switching causes a loss of power and lowers efficiency. This is because the switching speed increases and the switching frequency increases, so the power loss also increases but the efficiency actually decreases. In order to overcome the problem of power transfer efficiency, the programmed PWM method is applied to regulate the switching transition by eliminating low-harmonic signals. Thus, the power transfer efficiency can be increased by about 21.16% compared to the power transfer conditions in the benchmark.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase Gate Switch Control of BLDC Motor Driver for Power Transfer Efficiency
This paper examines the power transfer efficiency of three-phase gate switches to drive BLDC motors. The three-phase gate switch has six gate switches with eight switch states, which are used to control voltage or current. The effect of voltage arising on connection lines between gate switches can be determined by taking into account the rise time, fall time, and propagation delay parameters. Switching causes a loss of power and lowers efficiency. This is because the switching speed increases and the switching frequency increases, so the power loss also increases but the efficiency actually decreases. In order to overcome the problem of power transfer efficiency, the programmed PWM method is applied to regulate the switching transition by eliminating low-harmonic signals. Thus, the power transfer efficiency can be increased by about 21.16% compared to the power transfer conditions in the benchmark.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Internet of Things-Based Electrohydraulic Power Steering Performance of a Monitoring System
In this paper, a monitoring system has been developed that can be accessed and managed remotely using IoT technology to continually monitor the state of the electro hydraulic power steering (EHPS) performance. EHPS as an item, IoT devices, data gathering, and sensors are all part of the monitoring system. The EHPS performance can be examined based on the characteristics of the EHPS parameters based on the measured data from the sensor. Furthermore, the level of accuracy of measurement is determined by analyzing the percentage of accuracy and precision. As for the data transmission speed, it can be calculated based on the propagation delay and transmission delay. This monitoring system can be applied because it has an accuracy rate of around 96.82 % and has a good transmission speed.
- 6 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Internet of Things-Based Electrohydraulic Power Steering Performance of a Monitoring System
In this paper, a monitoring system has been developed that can be accessed and managed remotely using IoT technology to continually monitor the state of the electro hydraulic power steering (EHPS) performance. EHPS as an item, IoT devices, data gathering, and sensors are all part of the monitoring system. The EHPS performance can be examined based on the characteristics of the EHPS parameters based on the measured data from the sensor. Furthermore, the level of accuracy of measurement is determined by analyzing the percentage of accuracy and precision. As for the data transmission speed, it can be calculated based on the propagation delay and transmission delay. This monitoring system can be applied because it has an accuracy rate of around 96.82 % and has a good transmission speed.
- Open Access
- 27 June 2023
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 21 (3) , 457-470
Unsaturated Polyester Resin/Aluminum Tri-hydroxide Added with Short Glass Fiber for Battery Box
A battery box made of polymer material must consider mechanical strengthand flame retardancy. One solution to increase the flame retardancy of polymers is toadd a flame retardant filler. However, sometimes adding a flame retardant filler cancause degradation of mechanical strength compared to neat polymers. The combinationof more than one type of filler or hybrid fillers can produce the optimal combination offlame retardancy and mechanical strength. An experimental study was carried out tocharacterize several composite polymer samples of unsaturated polyester (UP) resincombined with fillers of aluminum tri-hydroxide (ATH) to increase flame retardancyand short glass fiber (G) to improve mechanical strength. The DSC results show thatthe maximum endothermic of all samples occurred at a temperature of around 70 ºC.The TGA results prove that ATH and G can maintain the thermal stability of UP so thatthe composite samples were degraded at higher temperatures by reducing the rate ofweight degradation due to a temperature of around 0.1%/ºC. The burning test alsoshows that samples with ATH and G have a lower burning rate value than neat UP. Formechanical characterization, the tensile strength of the samples with ATH and G waslower than that of neat UP. However, UP/ATH/G2 showed an optimal compositioncompared to other filler compositions with a tensile strength of 41.5 MPa. This samplealso produces an optimal bending strength of 68.9 MPa and even higher than neat UP.These results were confirmed by SEM observations, in which filler G was exfoliated inthe UP. The broken G particles on the fracture surface observation prove the goodinterlock bonding between UP and G, which contributes to increasing the mechanicalstrength of the UP composite.
- 27 June 2023
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 21 (3) , 457-470
Open AccessUnsaturated Polyester Resin/Aluminum Tri-hydroxide Added with Short Glass Fiber for Battery Box
A battery box made of polymer material must consider mechanical strengthand flame retardancy. One solution to increase the flame retardancy of polymers is toadd a flame retardant filler. However, sometimes adding a flame retardant filler cancause degradation of mechanical strength compared to neat polymers. The combinationof more than one type of filler or hybrid fillers can produce the optimal combination offlame retardancy and mechanical strength. An experimental study was carried out tocharacterize several composite polymer samples of unsaturated polyester (UP) resincombined with fillers of aluminum tri-hydroxide (ATH) to increase flame retardancyand short glass fiber (G) to improve mechanical strength. The DSC results show thatthe maximum endothermic of all samples occurred at a temperature of around 70 ºC.The TGA results prove that ATH and G can maintain the thermal stability of UP so thatthe composite samples were degraded at higher temperatures by reducing the rate ofweight degradation due to a temperature of around 0.1%/ºC. The burning test alsoshows that samples with ATH and G have a lower burning rate value than neat UP. Formechanical characterization, the tensile strength of the samples with ATH and G waslower than that of neat UP. However, UP/ATH/G2 showed an optimal compositioncompared to other filler compositions with a tensile strength of 41.5 MPa. This samplealso produces an optimal bending strength of 68.9 MPa and even higher than neat UP.These results were confirmed by SEM observations, in which filler G was exfoliated inthe UP. The broken G particles on the fracture surface observation prove the goodinterlock bonding between UP and G, which contributes to increasing the mechanicalstrength of the UP composite.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Wireless Position Control of an Electric Power Steering System for Energy Optimization
This paper proposed an energy optimization strategy with an optimal control method approach based on wireless position control of electric power steering (EPS). The optimal control method consists of a discrete linear quadratic regulator (DLQR) as case-1 and a predictive control model (MPC) as case-2. Both are applied to see the potential of the optimal energy based on the comparison of control performance, resulting in a control design that eliminates unwanted vibrations and ensures system stability, and energy efficiency. In addition, both of these control designs can be implemented in a wireless system for position control of EPS using a mobile phone.
- 13 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Wireless Position Control of an Electric Power Steering System for Energy Optimization
This paper proposed an energy optimization strategy with an optimal control method approach based on wireless position control of electric power steering (EPS). The optimal control method consists of a discrete linear quadratic regulator (DLQR) as case-1 and a predictive control model (MPC) as case-2. Both are applied to see the potential of the optimal energy based on the comparison of control performance, resulting in a control design that eliminates unwanted vibrations and ensures system stability, and energy efficiency. In addition, both of these control designs can be implemented in a wireless system for position control of EPS using a mobile phone.
- Open Access
- 30 November 2020
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 61-70
STRESS ANALYSIS SIMULATIONS OF WELDED AND BOLTED JOINTS METHOD FOR FULL STEEL AND COMPOSITE-STEEL CHASSIS STRUCTURE OF ELECTRIC LOW FLOOR MEDIUM BUS
Stress analysis of welded steel-to-steel, bolted steel-to-steel, and bolted composite-steel chassis in an electric low floor medium bus structure is presented in this paper. The analysis was carried out on the condition that is when the bus is full of load in idle/static. This condition reflects the situation of the vehicle in full load with passengers and components, which is important to be analyzed to anticipate the unwanted structural failure of the chassis. Finite Element Method (Harmonic response simulation) is used to investigate the structural behavior of both welded and bolted methods. Several parameters such as 2 Hertz for the maximum frequency, 5000 kg for the total vehicle weight, and the uniform distribution of load are used for this study to simulate the simplified, real application in the real world. The first comparison is between the welded and bolted steel-to-steel chassis which results in the bolted method has a lower stress value by the difference of 4.3 MPa in the joint section than the welded joint. This means that the bolted joint is more recommended than welded for the use as an electric low floor medium bus and has the potential to be optimized further. In terms of reducing the weight of the chassis structure, then lightweight material (carbon fiber composite) is used to replace the full steel chassis to be a composite-steel chassis. The use of this hybrid material depicts the stress value of 61.5 MPa in the joint area, this value is still far below the limit of carbon fiber that is 3200 MPa makes this bolted composite-steel is considerably safe in full load condition as an electric low floor medium bus structure. Using this hybrid bolted composite-steel chassis structure also reduces the total chassis weight by about 22.7 % compared to the full steel chassis structure, thus one could expect to extend the mileage of electric vehicles by more than 20 %
- 30 November 2020
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 61-70
Open AccessSTRESS ANALYSIS SIMULATIONS OF WELDED AND BOLTED JOINTS METHOD FOR FULL STEEL AND COMPOSITE-STEEL CHASSIS STRUCTURE OF ELECTRIC LOW FLOOR MEDIUM BUS
Stress analysis of welded steel-to-steel, bolted steel-to-steel, and bolted composite-steel chassis in an electric low floor medium bus structure is presented in this paper. The analysis was carried out on the condition that is when the bus is full of load in idle/static. This condition reflects the situation of the vehicle in full load with passengers and components, which is important to be analyzed to anticipate the unwanted structural failure of the chassis. Finite Element Method (Harmonic response simulation) is used to investigate the structural behavior of both welded and bolted methods. Several parameters such as 2 Hertz for the maximum frequency, 5000 kg for the total vehicle weight, and the uniform distribution of load are used for this study to simulate the simplified, real application in the real world. The first comparison is between the welded and bolted steel-to-steel chassis which results in the bolted method has a lower stress value by the difference of 4.3 MPa in the joint section than the welded joint. This means that the bolted joint is more recommended than welded for the use as an electric low floor medium bus and has the potential to be optimized further. In terms of reducing the weight of the chassis structure, then lightweight material (carbon fiber composite) is used to replace the full steel chassis to be a composite-steel chassis. The use of this hybrid material depicts the stress value of 61.5 MPa in the joint area, this value is still far below the limit of carbon fiber that is 3200 MPa makes this bolted composite-steel is considerably safe in full load condition as an electric low floor medium bus structure. Using this hybrid bolted composite-steel chassis structure also reduces the total chassis weight by about 22.7 % compared to the full steel chassis structure, thus one could expect to extend the mileage of electric vehicles by more than 20 %