Rais I. Mendgaziev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rais I. Mendgaziev has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
- Andrey. S. Stoporev
Gubkin University, Moscow, Russia
8 shared publications - Anton P. Semenov
Department of Physical and Colloid Chemistry, Gubkin University, 65, Leninsky Prospekt, Building 1, 119991 Moscow, Russia
8 shared publications - Daria V. Sergeeva
Skolkovo Institute of Science and Technology (Skoltech), Moscow, Russia
3 shared publications Vladimir A. Istomin
Gubkin Univ, Dept Phys & Colloid Chem, 65 Leninsky Prospekt,Bldg 1, Moscow 119991, Russia
3 shared publicationsVladimir A. Vinokurov
Gubkin Univ, Dept Phys & Colloid Chem, 65 Leninsky Prospekt,Bldg 1, Moscow 119991, Russia
3 shared publications- Vladimir Anatol'Evich Vinokurov
Gubkin Russian State University of Oil and Gas (National Research University), Moscow, Russia
3 shared publications
Latest Publications
- Open Access
- 13 February 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (4) , 1792
Thermodynamic Inhibition of Carbon Dioxide Hydrate with Magnesium Chloride and Methanol: Comparative Phase Equilibrium and PXRD Study
Clathrate hydrates of carbon dioxide represent a subject of considerable interest in both fundamental science and the development of promising technologies. The phase behavior of CO2 hydrate in the presence of concentrated aqueous solutions remains poorly understood. In this study, we conducted a comprehensive investigation into the impact of magnesium chloride (0–24 mass%) and methanol (0–40 mass%) on the thermodynamic stability of CO2 hydrate. New experimental data on the three-phase gas–aqueous solution–gas hydrate equilibrium in the temperature range 243–283 K and pressure range 1–4.5 MPa were obtained. A correlation is proposed for the precise representation of equilibrium pressure–temperature lines. A comparison of the anti-hydrate effect, as indicated by the parameter ∆Th, of these substances demonstrated that ionic MgCl2 exhibits a stronger thermodynamic inhibitory effect on CO2 hydrate formation than nonionic MeOH. The results of measuring the melting point of ice at 0.1 MPa for aqueous solutions of MgCl2 and MeOH confirmed the thermodynamic consistency of the hydrate equilibrium data. A detailed comparison of the anti-hydrate effect of MgCl2 and MeOH in a wide concentration range was performed on hydrates of different gases (CO2 and CH4). The phase composition of CO2 hydrate samples obtained from water and aqueous solutions of MgCl2 and MeOH was examined using powder X-ray diffraction (PXRD) at 133 K. The PXRD results indicate the formation of sI CO2 hydrate with a cell parameter of 11.86 ± 0.04 Å in all cases.
- 13 February 2026
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 27 (4) , 1792
Open AccessThermodynamic Inhibition of Carbon Dioxide Hydrate with Magnesium Chloride and Methanol: Comparative Phase Equilibrium and PXRD Study
Clathrate hydrates of carbon dioxide represent a subject of considerable interest in both fundamental science and the development of promising technologies. The phase behavior of CO2 hydrate in the presence of concentrated aqueous solutions remains poorly understood. In this study, we conducted a comprehensive investigation into the impact of magnesium chloride (0–24 mass%) and methanol (0–40 mass%) on the thermodynamic stability of CO2 hydrate. New experimental data on the three-phase gas–aqueous solution–gas hydrate equilibrium in the temperature range 243–283 K and pressure range 1–4.5 MPa were obtained. A correlation is proposed for the precise representation of equilibrium pressure–temperature lines. A comparison of the anti-hydrate effect, as indicated by the parameter ∆Th, of these substances demonstrated that ionic MgCl2 exhibits a stronger thermodynamic inhibitory effect on CO2 hydrate formation than nonionic MeOH. The results of measuring the melting point of ice at 0.1 MPa for aqueous solutions of MgCl2 and MeOH confirmed the thermodynamic consistency of the hydrate equilibrium data. A detailed comparison of the anti-hydrate effect of MgCl2 and MeOH in a wide concentration range was performed on hydrates of different gases (CO2 and CH4). The phase composition of CO2 hydrate samples obtained from water and aqueous solutions of MgCl2 and MeOH was examined using powder X-ray diffraction (PXRD) at 133 K. The PXRD results indicate the formation of sI CO2 hydrate with a cell parameter of 11.86 ± 0.04 Å in all cases.
- Open Access
- 17 May 2024
- Published by Elsevier in Data in Brief
- Vol. 54, 110517
Dataset on investigating nucleation and growth kinetics of methane hydrate in aqueous methanol solutions
- 17 May 2024
- Published by Elsevier in Data in Brief
- Vol. 54, 110517
Open AccessDataset on investigating nucleation and growth kinetics of methane hydrate in aqueous methanol solutions
- 5 October 2023
- Published by Elsevier in Chemical Engineering Science
- Vol. 283
Searching for synergy between alcohol and salt to produce more potent and environmentally benign gas hydrate inhibitors
- 5 October 2023
- Published by Elsevier in Chemical Engineering Science
- Vol. 283
Searching for synergy between alcohol and salt to produce more potent and environmentally benign gas hydrate inhibitors
- Open Access
Polyurethane/n-Octadecane Phase-Change Microcapsules via Emulsion Interfacial Polymerization: The Effect of Paraffin Loading on Capsule Shell Formation and Latent Heat Storage Properties
Organic phase-change materials (PCMs) hold promise in developing advanced thermoregulation and responsive energy systems owing to their high latent heat capacity and thermal reliability. However, organic PCMs are prone to leakages in the liquid state and, thus, are hardly applicable in their pristine form. Herein, we encapsulated organic PCM n-Octadecane into polyurethane capsules via polymerization of commercially available polymethylene polyphenylene isocyanate and polyethylene glycol at the interface oil-in-water emulsion and studied how various n-Octadecane feeding affected the shell formation, capsule structure, and latent heat storage properties. The successful shell polymerization and encapsulation of n-Octadecane dissolved in the oil core was verified by confocal microscopy and Fourier-transform infrared spectroscopy. The mean capsule size varied from 9.4 to 16.7 µm while the shell was found to reduce in thickness from 460 to 220 nm as the n-Octadecane feeding increased. Conversely, the latent heat storage capacity increased from 50 to 132 J/g corresponding to the growth in actual n-Octadecane content from 25% to 67% as revealed by differential scanning calorimetry. The actual n-Octadecane content increased non-linearly along with the n-Octadecane feeding and reached a plateau at 66–67% corresponded to 3.44–3.69 core-to-monomer ratio. Finally, the capsules with the reasonable combination of structural and thermal properties were evaluated as a thermoregulating additive to a commercially available paint.
Open AccessPolyurethane/n-Octadecane Phase-Change Microcapsules via Emulsion Interfacial Polymerization: The Effect of Paraffin Loading on Capsule Shell Formation and Latent Heat Storage Properties
Organic phase-change materials (PCMs) hold promise in developing advanced thermoregulation and responsive energy systems owing to their high latent heat capacity and thermal reliability. However, organic PCMs are prone to leakages in the liquid state and, thus, are hardly applicable in their pristine form. Herein, we encapsulated organic PCM n-Octadecane into polyurethane capsules via polymerization of commercially available polymethylene polyphenylene isocyanate and polyethylene glycol at the interface oil-in-water emulsion and studied how various n-Octadecane feeding affected the shell formation, capsule structure, and latent heat storage properties. The successful shell polymerization and encapsulation of n-Octadecane dissolved in the oil core was verified by confocal microscopy and Fourier-transform infrared spectroscopy. The mean capsule size varied from 9.4 to 16.7 µm while the shell was found to reduce in thickness from 460 to 220 nm as the n-Octadecane feeding increased. Conversely, the latent heat storage capacity increased from 50 to 132 J/g corresponding to the growth in actual n-Octadecane content from 25% to 67% as revealed by differential scanning calorimetry. The actual n-Octadecane content increased non-linearly along with the n-Octadecane feeding and reached a plateau at 66–67% corresponded to 3.44–3.69 core-to-monomer ratio. Finally, the capsules with the reasonable combination of structural and thermal properties were evaluated as a thermoregulating additive to a commercially available paint.
- Open Access
- 29 May 2023
- Published by Elsevier in Data in Brief
- Vol. 48, 109283
Dataset for the experimental study of dimethyl sulfoxide as a thermodynamic inhibitor of methane hydrate formation
- 29 May 2023
- Published by Elsevier in Data in Brief
- Vol. 48, 109283
Open AccessDataset for the experimental study of dimethyl sulfoxide as a thermodynamic inhibitor of methane hydrate formation
- Open Access
- 26 May 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (11) , 9321
Direct Measurement of the Four-Phase Equilibrium Coexistence Vapor–Aqueous Solution–Ice–Gas Hydrate in Water–Carbon Dioxide System
Precise data on the non-variant equilibrium of the four phases (vapor–aqueous solution–ice–gas hydrate) in P–T coordinates are highly desired for developing accurate thermodynamic models and can be used as reference points (similar to the triple point of water). Using the two-component hydrate-forming system CO2–H2O, we have proposed and validated a new express procedure for determining the temperature and pressure of the lower quadruple point Q1. The essence of the method is the direct measurement of these parameters after the successive formation of the gas hydrate and ice phases in the initial two-phase gas–water solution system under intense agitation of the fluids. After relaxation, the system occurs in the same equilibrium state (T = 271.60 K, P = 1.044 MPa), regardless of the initial parameters and the order of crystallization of the CO2 hydrate and ice phases. Considering the combined standard uncertainties (±0.023 K, ±0.021 MPa), the determined P and T values agree with the results of other authors obtained by a more sophisticated indirect method. Validating the developed approach for systems with other hydrate-forming gases is of great interest.
- 26 May 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (11) , 9321
Open AccessDirect Measurement of the Four-Phase Equilibrium Coexistence Vapor–Aqueous Solution–Ice–Gas Hydrate in Water–Carbon Dioxide System
Precise data on the non-variant equilibrium of the four phases (vapor–aqueous solution–ice–gas hydrate) in P–T coordinates are highly desired for developing accurate thermodynamic models and can be used as reference points (similar to the triple point of water). Using the two-component hydrate-forming system CO2–H2O, we have proposed and validated a new express procedure for determining the temperature and pressure of the lower quadruple point Q1. The essence of the method is the direct measurement of these parameters after the successive formation of the gas hydrate and ice phases in the initial two-phase gas–water solution system under intense agitation of the fluids. After relaxation, the system occurs in the same equilibrium state (T = 271.60 K, P = 1.044 MPa), regardless of the initial parameters and the order of crystallization of the CO2 hydrate and ice phases. Considering the combined standard uncertainties (±0.023 K, ±0.021 MPa), the determined P and T values agree with the results of other authors obtained by a more sophisticated indirect method. Validating the developed approach for systems with other hydrate-forming gases is of great interest.
- Open Access
Phase-Change Microcapsules with a Stable Polyurethane Shell through the Direct Crosslinking of Cellulose Nanocrystals with Polyisocyanate at the Oil/Water Interface of Pickering Emulsion
Phase-change materials (PCMs) attract much attention with regard to their capability of mitigating fossil fuel-based heating in in-building applications, due to the responsive accumulation and release of thermal energy as a latent heat of reversible phase transitions. Organic PCMs possess high latent heat storage capacity and thermal reliability. However, bare PCMs suffer from leakages in the liquid form. Here, we demonstrate a reliable approach to improve the shape stability of organic PCM n-octadecane by encapsulation via interfacial polymerization at an oil/water interface of Pickering emulsion. Cellulose nanocrystals are employed as emulsion stabilizers and branched oligo-polyol with high functionality to crosslink the polyurethane shell in reaction with polyisocyanate dissolved in the oil core. This gives rise to a rigid polyurethane structure with a high density of urethane groups. The formation of a polyurethane shell and successful encapsulation of n-octadecane is confirmed by FTIR spectroscopy, XRD analysis, and fluorescent confocal microscopy. Electron microscopy reveals the formation of non-aggregated capsules with an average size of 18.6 µm and a smooth uniform shell with the thickness of 450 nm. The capsules demonstrate a latent heat storage capacity of 79 J/g, while the encapsulation of n-octadecane greatly improves its shape and thermal stability compared with bulk paraffin.
Open AccessPhase-Change Microcapsules with a Stable Polyurethane Shell through the Direct Crosslinking of Cellulose Nanocrystals with Polyisocyanate at the Oil/Water Interface of Pickering Emulsion
Phase-change materials (PCMs) attract much attention with regard to their capability of mitigating fossil fuel-based heating in in-building applications, due to the responsive accumulation and release of thermal energy as a latent heat of reversible phase transitions. Organic PCMs possess high latent heat storage capacity and thermal reliability. However, bare PCMs suffer from leakages in the liquid form. Here, we demonstrate a reliable approach to improve the shape stability of organic PCM n-octadecane by encapsulation via interfacial polymerization at an oil/water interface of Pickering emulsion. Cellulose nanocrystals are employed as emulsion stabilizers and branched oligo-polyol with high functionality to crosslink the polyurethane shell in reaction with polyisocyanate dissolved in the oil core. This gives rise to a rigid polyurethane structure with a high density of urethane groups. The formation of a polyurethane shell and successful encapsulation of n-octadecane is confirmed by FTIR spectroscopy, XRD analysis, and fluorescent confocal microscopy. Electron microscopy reveals the formation of non-aggregated capsules with an average size of 18.6 µm and a smooth uniform shell with the thickness of 450 nm. The capsules demonstrate a latent heat storage capacity of 79 J/g, while the encapsulation of n-octadecane greatly improves its shape and thermal stability compared with bulk paraffin.
- Open Access
Performance of Waterborne Polyurethanes in Inhibition of Gas Hydrate Formation and Corrosion: Influence of Hydrophobic Fragments
The design of new dual-function inhibitors simultaneously preventing hydrate formation and corrosion is a relevant issue for the oil and gas industry. The structure-property relationship for a promising class of hybrid inhibitors based on waterborne polyurethanes (WPU) was studied in this work. Variation of diethanolamines differing in the size and branching of N-substituents (methyl, n-butyl, and tert-butyl), as well as the amount of these groups, allowed the structure of polymer molecules to be preset during their synthesis. To assess the hydrate and corrosion inhibition efficiency of developed reagents pressurized rocking cells, electrochemistry and weight-loss techniques were used. A distinct effect of these variables altering the hydrophobicity of obtained compounds on their target properties was revealed. Polymers with increased content of diethanolamine fragments with n- or tert-butyl as N-substituent (WPU-6 and WPU-7, respectively) worked as dual-function inhibitors, showing nearly the same efficiency as commercial ones at low concentration (0.25 wt%), with the branched one (tert-butyl; WPU-7) turning out to be more effective as a corrosion inhibitor. Commercial kinetic hydrate inhibitor Luvicap 55 W and corrosion inhibitor Armohib CI-28 were taken as reference samples. Preliminary study reveals that WPU-6 and WPU-7 polyurethanes as well as Luvicap 55 W are all poorly biodegradable compounds; BODt/CODcr (ratio of Biochemical oxygen demand and Chemical oxygen demand) value is 0.234 and 0.294 for WPU-6 and WPU-7, respectively, compared to 0.251 for commercial kinetic hydrate inhibitor Luvicap 55 W. Since the obtained polyurethanes have a bifunctional effect and operate at low enough concentrations, their employment is expected to reduce both operating costs and environmental impact.
Open AccessPerformance of Waterborne Polyurethanes in Inhibition of Gas Hydrate Formation and Corrosion: Influence of Hydrophobic Fragments
The design of new dual-function inhibitors simultaneously preventing hydrate formation and corrosion is a relevant issue for the oil and gas industry. The structure-property relationship for a promising class of hybrid inhibitors based on waterborne polyurethanes (WPU) was studied in this work. Variation of diethanolamines differing in the size and branching of N-substituents (methyl, n-butyl, and tert-butyl), as well as the amount of these groups, allowed the structure of polymer molecules to be preset during their synthesis. To assess the hydrate and corrosion inhibition efficiency of developed reagents pressurized rocking cells, electrochemistry and weight-loss techniques were used. A distinct effect of these variables altering the hydrophobicity of obtained compounds on their target properties was revealed. Polymers with increased content of diethanolamine fragments with n- or tert-butyl as N-substituent (WPU-6 and WPU-7, respectively) worked as dual-function inhibitors, showing nearly the same efficiency as commercial ones at low concentration (0.25 wt%), with the branched one (tert-butyl; WPU-7) turning out to be more effective as a corrosion inhibitor. Commercial kinetic hydrate inhibitor Luvicap 55 W and corrosion inhibitor Armohib CI-28 were taken as reference samples. Preliminary study reveals that WPU-6 and WPU-7 polyurethanes as well as Luvicap 55 W are all poorly biodegradable compounds; BODt/CODcr (ratio of Biochemical oxygen demand and Chemical oxygen demand) value is 0.234 and 0.294 for WPU-6 and WPU-7, respectively, compared to 0.251 for commercial kinetic hydrate inhibitor Luvicap 55 W. Since the obtained polyurethanes have a bifunctional effect and operate at low enough concentrations, their employment is expected to reduce both operating costs and environmental impact.
- 1 January 2019
- Published by Springer Nature in Chemistry and Technology of Fuels and Oils
- Vol. 54 (6) , 738-742
Synergism of Methanol and Magnesium Chloride for Thermodynamic Inhibition of Methane Hydrate
- 1 January 2019
- Published by Springer Nature in Chemistry and Technology of Fuels and Oils
- Vol. 54 (6) , 738-742
Synergism of Methanol and Magnesium Chloride for Thermodynamic Inhibition of Methane Hydrate