Ken Chun Kit Uy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ken Chun Kit Uy has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Chih-Yung Wen
The Hong Kong Polytechnic University
12 shared publications - Jiaao Hao
The Hong Kong Polytechnic University
5 shared publications - Jiachen Lu
The Hong Kong Polytechnic University
3 shared publications - Lisong Shi
The Hong Kong Polytechnic University
3 shared publications - Rui Zhao
Beijing Institute of Technology
3 shared publications Lisong Shi
2 shared publications
Latest Publications
- Open Access
- 17 May 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 241
Influence of reactant spatial heterogeneity on propagation and performance of hydrogen-fueled rotating detonation waves
- 17 May 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 241
Open AccessInfluence of reactant spatial heterogeneity on propagation and performance of hydrogen-fueled rotating detonation waves
- 5 March 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 176
Stabilization mechanisms of first Mack mode in supersonic flat plate flows
- 5 March 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 176
Stabilization mechanisms of first Mack mode in supersonic flat plate flows
- 26 January 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- p. 1-14
Crossflow Effects on the Global Stability of Hypersonic Compression Corner Flow
Hypersonic compression corner flow with crossflow at the leading edge of the flat plate is investigated through global stability analysis (GSA) and direct numerical simulation (DNS). Base flow conditions with a Mach number of 7.7 and a unit Reynolds number of [ ] are selected. The effects of varying sweep angles (0–50 deg) and ramp angles (12–15 deg) are examined. The results reveal multiple local maxima in temporal amplification rate with different spanwise wavenumbers signifying oscillatory modes in the presence of crossflow, one of which corresponds to the leading stationary mode observed in unswept flows. The introduction of crossflow induces streamwise periodicity in the reattached boundary layer. The critical ramp angle of 14 deg is further discussed, where the flow becomes globally stable at moderate sweep angles and globally unstable at higher sweep angles, with changes in the leading global mode under varying crossflow intensities. DNS of a globally unstable case demonstrates good agreement with the GSA’s most unstable mode during the linear growth stage. In the saturated stage, harmonics of the most unstable global mode are observed, followed by the emergence of broadband unsteadiness.
- 26 January 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- p. 1-14
Crossflow Effects on the Global Stability of Hypersonic Compression Corner Flow
Hypersonic compression corner flow with crossflow at the leading edge of the flat plate is investigated through global stability analysis (GSA) and direct numerical simulation (DNS). Base flow conditions with a Mach number of 7.7 and a unit Reynolds number of [ ] are selected. The effects of varying sweep angles (0–50 deg) and ramp angles (12–15 deg) are examined. The results reveal multiple local maxima in temporal amplification rate with different spanwise wavenumbers signifying oscillatory modes in the presence of crossflow, one of which corresponds to the leading stationary mode observed in unswept flows. The introduction of crossflow induces streamwise periodicity in the reattached boundary layer. The critical ramp angle of 14 deg is further discussed, where the flow becomes globally stable at moderate sweep angles and globally unstable at higher sweep angles, with changes in the leading global mode under varying crossflow intensities. DNS of a globally unstable case demonstrates good agreement with the GSA’s most unstable mode during the linear growth stage. In the saturated stage, harmonics of the most unstable global mode are observed, followed by the emergence of broadband unsteadiness.
- 15 October 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1021, A18
On the receptivity of first and cross-flow modes in hypersonic sharp wing flows
A long-standing conceptual debate regarding the identification and independence of first Mack and cross-flow instabilities is clarified over a Mach 5.9 sharp wing at zero angle of attack and varying sweep angles. Their receptivity of the boundary layers to three-dimensional slow acoustic and vorticity waves is investigated using linear stability theory, direct numerical simulation and momentum potential theory (MPT). Linear stability theory demonstrates that the targeted slow mode appears as the oblique first mode at small sweep angles ( $0^\circ$ and $15^\circ$ ) and transitions to the cross-flow mode at larger sweep angles ( $30^\circ$ and $45^\circ$ ). Direct numerical simulation indicates that both the oblique first mode and cross-flow mode share identical receptivity pathways: for slow acoustic waves, the pathway comprises ‘leading-edge damping–enhanced exponential growth–linear growth’ stages. For vorticity waves, it consists of ‘leading-edge damping–non-modal growth–linear growth’ stages. Momentum potential theory decomposes the fluctuation momentum density into vortical, acoustic and thermal components, revealing unified receptivity mechanisms: for slow acoustic waves, the leading-edge damping is caused by strong acoustic components generated through synchronization. The enhanced exponential growth stage is dominated by steadily growing vortical components, with acoustic and thermal components remaining at small amplitudes. For vorticity waves, leading-edge disturbances primarily consist of vortical components, indicating a distinct mechanism from slow acoustic waves. Non-modal stages originate from adjustments among MPT components. Vortical components dominate the linear growth stage for both instabilities. These uniform behaviours between first Mack and cross-flow modes highlight their consistency.- 15 October 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1021, A18
On the receptivity of first and cross-flow modes in hypersonic sharp wing flows
A long-standing conceptual debate regarding the identification and independence of first Mack and cross-flow instabilities is clarified over a Mach 5.9 sharp wing at zero angle of attack and varying sweep angles. Their receptivity of the boundary layers to three-dimensional slow acoustic and vorticity waves is investigated using linear stability theory, direct numerical simulation and momentum potential theory (MPT). Linear stability theory demonstrates that the targeted slow mode appears as the oblique first mode at small sweep angles ( $0^\circ$ and $15^\circ$ ) and transitions to the cross-flow mode at larger sweep angles ( $30^\circ$ and $45^\circ$ ). Direct numerical simulation indicates that both the oblique first mode and cross-flow mode share identical receptivity pathways: for slow acoustic waves, the pathway comprises ‘leading-edge damping–enhanced exponential growth–linear growth’ stages. For vorticity waves, it consists of ‘leading-edge damping–non-modal growth–linear growth’ stages. Momentum potential theory decomposes the fluctuation momentum density into vortical, acoustic and thermal components, revealing unified receptivity mechanisms: for slow acoustic waves, the leading-edge damping is caused by strong acoustic components generated through synchronization. The enhanced exponential growth stage is dominated by steadily growing vortical components, with acoustic and thermal components remaining at small amplitudes. For vorticity waves, leading-edge disturbances primarily consist of vortical components, indicating a distinct mechanism from slow acoustic waves. Non-modal stages originate from adjustments among MPT components. Vortical components dominate the linear growth stage for both instabilities. These uniform behaviours between first Mack and cross-flow modes highlight their consistency.- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Acoustic–vortical evolution mechanisms of supersonic first Mack mode
This study employs linear stability theory, direct numerical simulation, and momentum potential theory to investigate the physical characteristics of the first mode at varying spanwise wavenumbers in a Mach 4.5 flat-plate boundary layer and subsequently examines the influence of porous coatings. As the spanwise wavenumber increases, the streamwise wavenumber initially rises before declining, with its maximum marking the transition of the first mode from an acoustic to a vortical nature. Momentum potential theory is then applied to decompose fluctuating momentum in the perturbation field into vortical, acoustic, and thermal components. The results indicate that as the spanwise wavenumber increases, the proportion of acoustic components diminishes, while vortical components progressively dominate. These distinct physical characteristics lead to divergent responses to porous coatings: Slightly oblique first modes are modulated by scattering effects and wall admittance, while highly oblique first modes are destabilized by mean flow distortions induced by the coatings.
- 1 July 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (7)
Acoustic–vortical evolution mechanisms of supersonic first Mack mode
This study employs linear stability theory, direct numerical simulation, and momentum potential theory to investigate the physical characteristics of the first mode at varying spanwise wavenumbers in a Mach 4.5 flat-plate boundary layer and subsequently examines the influence of porous coatings. As the spanwise wavenumber increases, the streamwise wavenumber initially rises before declining, with its maximum marking the transition of the first mode from an acoustic to a vortical nature. Momentum potential theory is then applied to decompose fluctuating momentum in the perturbation field into vortical, acoustic, and thermal components. The results indicate that as the spanwise wavenumber increases, the proportion of acoustic components diminishes, while vortical components progressively dominate. These distinct physical characteristics lead to divergent responses to porous coatings: Slightly oblique first modes are modulated by scattering effects and wall admittance, while highly oblique first modes are destabilized by mean flow distortions induced by the coatings.
- Open Access
- 9 June 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1012, A29
Characterising Görtler vortices in supersonic turbulent flows over concave surfaces
Görtler vortices induced by concave curvature in supersonic turbulent flows are investigated using resolvent analysis and large-eddy simulations at Mach 2.95 and Reynolds number $ Re_{\delta }=63\,500$ based on the boundary-layer thickness $ \delta$ . Resolvent analysis reveals that the most amplified coherent structures manifest as streamwise counter-rotating vortices with optimal spanwise wavelength $ 2.4\delta$ at cut-off frequency $f\delta /{u}_{\infty } =0.036$ , where $ {u}_{\infty }$ is the freestream velocity. The leading spectral proper orthogonal decomposition modes with spanwise wavelength approximately $ 2\delta$ align well with the predicted coherent structures from resolvent analysis at $f\delta /{u}_{\infty } =0.036$ . These predicted and extracted coherent structures are identified as Görtler vortices, driven by the Görtler instability. The preferential spanwise scale of the Görtler vortices is further examined under varying geometric and freestream parameters. The optimal spanwise wavelength is insensitive to the total turning angle beyond a critical value, but sensitive to the concave curvature $ K$ at the same turning angle. A limit spanwise wavelength $ 1.96\delta$ , corresponding to an infinite concave curvature as $ K\rightarrow \infty$ , is identified and validated. Increasing the freestream Mach number or decreasing the ratio of wall temperature to freestream temperature reduces the optimal wavelength normalised by $ \delta$ , while variations in freestream Reynolds number have negligible impact. Additionally, a modified definition of the turbulent Görtler number $ G_{T}$ based on the peak eddy viscosity in boundary layers is proposed and employed to assess the occurrence of Görtler instability.- 9 June 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1012, A29
Open AccessCharacterising Görtler vortices in supersonic turbulent flows over concave surfaces
Görtler vortices induced by concave curvature in supersonic turbulent flows are investigated using resolvent analysis and large-eddy simulations at Mach 2.95 and Reynolds number $ Re_{\delta }=63\,500$ based on the boundary-layer thickness $ \delta$ . Resolvent analysis reveals that the most amplified coherent structures manifest as streamwise counter-rotating vortices with optimal spanwise wavelength $ 2.4\delta$ at cut-off frequency $f\delta /{u}_{\infty } =0.036$ , where $ {u}_{\infty }$ is the freestream velocity. The leading spectral proper orthogonal decomposition modes with spanwise wavelength approximately $ 2\delta$ align well with the predicted coherent structures from resolvent analysis at $f\delta /{u}_{\infty } =0.036$ . These predicted and extracted coherent structures are identified as Görtler vortices, driven by the Görtler instability. The preferential spanwise scale of the Görtler vortices is further examined under varying geometric and freestream parameters. The optimal spanwise wavelength is insensitive to the total turning angle beyond a critical value, but sensitive to the concave curvature $ K$ at the same turning angle. A limit spanwise wavelength $ 1.96\delta$ , corresponding to an infinite concave curvature as $ K\rightarrow \infty$ , is identified and validated. Increasing the freestream Mach number or decreasing the ratio of wall temperature to freestream temperature reduces the optimal wavelength normalised by $ \delta$ , while variations in freestream Reynolds number have negligible impact. Additionally, a modified definition of the turbulent Görtler number $ G_{T}$ based on the peak eddy viscosity in boundary layers is proposed and employed to assess the occurrence of Görtler instability. - 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Coexistence of different mechanisms underlying the dynamics of supersonic turbulent flow over a compression ramp
Supersonic turbulent flow over a compression ramp is studied using wall-resolved large eddy simulation with a freestream Mach number of 2.95 and a Reynolds number [based on δ0: the thickness of incoming turbulent boundary layer (TBL)] of 63 560. The unsteady dynamics of the present shock wave/turbulent boundary layer interaction (STBLI) flow are investigated by using dynamic mode decomposition techniques, linear and nonlinear disambiguation optimization, local stability analysis (LSA), and global stability analysis (GSA). By analyzing the dynamic system for the STBLI flow, three dynamically important modes with characteristic spanwise wavelengths of 2δ0, 3δ0, and 6δ0 are captured. The 2δ0 mode approximates the spanwise scale of the Görtler-like vortices and Görtler mode of LSA, suggesting the presence of Görtler instability, which is believed to be related to the unsteady motion of streaks downstream of reattachment in the flow. The features of the 3δ0 mode are also observed in large-scale motions of the incoming TBL, implying the existence of a convective mechanism that is excited and maintained by such motions. Additionally, the GSA results show the most unstable mode features a spanwise wavelength of around 6δ0, indicating the existence of global instability that is believed to be related to the oscillating motion of separation shock. The coexistence of these three mechanisms is confirmed. Discussions on the above findings provide an interpretation for low-frequency unsteadiness that the unsteadiness of surface streaks results from the combined effects of the Görtler instability near flow reattachment and the convection of large-scale motions in the incoming boundary layer, while the low-frequency shock motion may be related to a global mode driven by upstream disturbances.
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Coexistence of different mechanisms underlying the dynamics of supersonic turbulent flow over a compression ramp
Supersonic turbulent flow over a compression ramp is studied using wall-resolved large eddy simulation with a freestream Mach number of 2.95 and a Reynolds number [based on δ0: the thickness of incoming turbulent boundary layer (TBL)] of 63 560. The unsteady dynamics of the present shock wave/turbulent boundary layer interaction (STBLI) flow are investigated by using dynamic mode decomposition techniques, linear and nonlinear disambiguation optimization, local stability analysis (LSA), and global stability analysis (GSA). By analyzing the dynamic system for the STBLI flow, three dynamically important modes with characteristic spanwise wavelengths of 2δ0, 3δ0, and 6δ0 are captured. The 2δ0 mode approximates the spanwise scale of the Görtler-like vortices and Görtler mode of LSA, suggesting the presence of Görtler instability, which is believed to be related to the unsteady motion of streaks downstream of reattachment in the flow. The features of the 3δ0 mode are also observed in large-scale motions of the incoming TBL, implying the existence of a convective mechanism that is excited and maintained by such motions. Additionally, the GSA results show the most unstable mode features a spanwise wavelength of around 6δ0, indicating the existence of global instability that is believed to be related to the oscillating motion of separation shock. The coexistence of these three mechanisms is confirmed. Discussions on the above findings provide an interpretation for low-frequency unsteadiness that the unsteadiness of surface streaks results from the combined effects of the Görtler instability near flow reattachment and the convection of large-scale motions in the incoming boundary layer, while the low-frequency shock motion may be related to a global mode driven by upstream disturbances.
- Open Access
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
Coexistence of stationary Görtler and crossflow instabilities in boundary layers
The coexistence of stationary Görtler and crossflow instabilities in boundary layers covering incompressible to hypersonic regimes is investigated by varying the local sweep angle, pressure gradient, wall curvature, and wall temperature using linear stability analysis. The results show that increasing the local sweep angle under a fixed concave curvature in incompressible boundary layers leads to the appearance of two unstable modes at certain sweep angles, which is conventionally known as the “changeover” regime between the crossflow and Görtler modes. This study identifies a synchronization between the two modes under this condition, which is similar to multiple Görtler modes and thus referred to as Görtler–crossflow modes. Three scenarios are presented to describe the possible development of these modal instabilities. In addition, increasing the concave curvature destabilizes the instability, while introducing a pressure gradient stabilizes the instability and results in a shrinkage of the unstable band of the spanwise wavenumber, as reported in the literature. In supersonic and hypersonic boundary layers, synchronization can occur near specific sweep angles and under cold wall conditions in supersonic boundary layers. As Mach number increases, the synchronization regime shifts toward lower sweep angles and wall temperature, in which the former reflects a decline in crossflow strength relative to Görtler instability, while the latter indicates the influence of thermal effects on synchronization. In hypersonic boundary layers, the crossflow instability is insignificant compared with the Görtler instability. No synchronization is identified under various parameter changes, and the first Görtler–crossflow mode dominates across the entire spanwise wavenumber ranges.
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
Open AccessCoexistence of stationary Görtler and crossflow instabilities in boundary layers
The coexistence of stationary Görtler and crossflow instabilities in boundary layers covering incompressible to hypersonic regimes is investigated by varying the local sweep angle, pressure gradient, wall curvature, and wall temperature using linear stability analysis. The results show that increasing the local sweep angle under a fixed concave curvature in incompressible boundary layers leads to the appearance of two unstable modes at certain sweep angles, which is conventionally known as the “changeover” regime between the crossflow and Görtler modes. This study identifies a synchronization between the two modes under this condition, which is similar to multiple Görtler modes and thus referred to as Görtler–crossflow modes. Three scenarios are presented to describe the possible development of these modal instabilities. In addition, increasing the concave curvature destabilizes the instability, while introducing a pressure gradient stabilizes the instability and results in a shrinkage of the unstable band of the spanwise wavenumber, as reported in the literature. In supersonic and hypersonic boundary layers, synchronization can occur near specific sweep angles and under cold wall conditions in supersonic boundary layers. As Mach number increases, the synchronization regime shifts toward lower sweep angles and wall temperature, in which the former reflects a decline in crossflow strength relative to Görtler instability, while the latter indicates the influence of thermal effects on synchronization. In hypersonic boundary layers, the crossflow instability is insignificant compared with the Görtler instability. No synchronization is identified under various parameter changes, and the first Görtler–crossflow mode dominates across the entire spanwise wavenumber ranges.
- 14 July 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Stabilization of hypersonic boundary-layer instability using porous coatings under thermochemical nonequilibrium
- 14 July 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Stabilization of hypersonic boundary-layer instability using porous coatings under thermochemical nonequilibrium
- 1 December 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (12) , 126101
Linear stability analysis of one-dimensional detonation coupled with vibrational relaxation
The linear stability of one-dimensional detonations with one-reaction chemistry coupled with molecular vibration nonequilibrium is investigated using the normal mode approach. The chemical kinetics in the Arrhenius form depend on an averaged temperature model that consists of translational–rotational mode and vibrational mode. The Landau–Teller model is applied to specify the vibrational relaxation. A time ratio is introduced to denote the ratio between the chemical time scale and the vibrational time scale in this study, which governs the vibrational relaxation rate in this coupling kinetics. The stability spectrum of disturbance eigenmodes is obtained by varying the bifurcation parameters independently at a different time ratio. These parameters include the activation energy, the degree of overdrive, the characteristic vibrational temperature, and the heat release. The results indicate that the neutral stability limit shifts to higher activation energy on the vibrational nonequilibrium side with a smaller time ratio, implying that the detonation is stabilized. A similar observation is seen at a lower degree of overdrive. Compared with the above two parameters, the characteristic vibrational temperature plays a minor role in the stabilization of detonation, and no change in the number of eigenmodes is identified throughout the selected range. By plotting the neutral stability curves relating the heat release to the above parameters, the decreases in instability ranges are obviously seen under vibrational nonequilibrium. The thermal nonequilibrium effect on detonation stability is clearly demonstrated. The analysis presented in this paper is ultimately justified by comparing the results with numerical simulation.
- 1 December 2020
- Published by AIP Publishing in Physics of Fluids
- Vol. 32 (12) , 126101
Linear stability analysis of one-dimensional detonation coupled with vibrational relaxation
The linear stability of one-dimensional detonations with one-reaction chemistry coupled with molecular vibration nonequilibrium is investigated using the normal mode approach. The chemical kinetics in the Arrhenius form depend on an averaged temperature model that consists of translational–rotational mode and vibrational mode. The Landau–Teller model is applied to specify the vibrational relaxation. A time ratio is introduced to denote the ratio between the chemical time scale and the vibrational time scale in this study, which governs the vibrational relaxation rate in this coupling kinetics. The stability spectrum of disturbance eigenmodes is obtained by varying the bifurcation parameters independently at a different time ratio. These parameters include the activation energy, the degree of overdrive, the characteristic vibrational temperature, and the heat release. The results indicate that the neutral stability limit shifts to higher activation energy on the vibrational nonequilibrium side with a smaller time ratio, implying that the detonation is stabilized. A similar observation is seen at a lower degree of overdrive. Compared with the above two parameters, the characteristic vibrational temperature plays a minor role in the stabilization of detonation, and no change in the number of eigenmodes is identified throughout the selected range. By plotting the neutral stability curves relating the heat release to the above parameters, the decreases in instability ranges are obviously seen under vibrational nonequilibrium. The thermal nonequilibrium effect on detonation stability is clearly demonstrated. The analysis presented in this paper is ultimately justified by comparing the results with numerical simulation.