Shotaro Yamashita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shotaro Yamashita has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
Kazuyoshi Saida
Graduate School of Engineering, Osaka University, Osaka, Japan
11 shared publications- Tomo Ogura
Osaka University
3 shared publications Aren Uegaki
Graduate School of Engineering, Osaka University, Osaka, Japan
2 shared publicationsDong-Cho Kim
2 shared publicationsMasato Takeuchi
Shibaura Machine Co., Ltd, Tokyo, Japan
2 shared publicationsRyosuke Hamada
2 shared publications
Latest Publications
- 26 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (10) , 723-734
Prevention of solidification cracking in alloy 718 additive manufacturing by laser metal deposition method based on control guidelines for weld solidification cracking
- 26 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (10) , 723-734
Prevention of solidification cracking in alloy 718 additive manufacturing by laser metal deposition method based on control guidelines for weld solidification cracking
- 16 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (9) , 660-672
Elucidation and verification of cracking behavior in additive manufacturing of alloy 718 based on fractography
- 16 September 2024
- Published by Taylor & Francis in Welding International
- Vol. 38 (9) , 660-672
Elucidation and verification of cracking behavior in additive manufacturing of alloy 718 based on fractography
- 2 November 2022
- Published by Taylor & Francis in Welding International
- Vol. 36 (11) , 693-704
Influence mechanism of solidification mode on solidification cracking susceptibility of stainless steel
It is well-known that the solidification cracking susceptibility of stainless steel changes depending on the amount of ferrite in the weld metal at room temperature. However, the cause and effect of the amount of ferrite at room temperature and solidification cracking have not always been clarified. When considering the temperature range in which solidification cracks occur, it must be necessary to focus on changes in microstructure and behavior during solidification. In this study, the solidification cracking susceptibility of stainless steel was investigated according to the above reasons, and its susceptibility was summarized using the solidification mode, in other words, an amount of delta ferrite during solidification. A quenched microstructure at the solid–liquid coexistence region was obtained for each stainless steel, and the solidification mode and the amount of the delta ferrite during solidification were investigated. The solidification cracking susceptibility was evaluated using the Trans-Varestraint test, and the effect of solidification mode on the brittle temperature range (BTR) was clarified. In addition, a theoretical study on BTR was conducted, and the effect of solidification mode on solidification segregation at each stainless steel was considered. It was found that the solidification segregation behavior changes depending on the solidification mode. Especially, the effect of solidification and segregation of impurity elements such as sulfur and phosphorus were large in the austenite, in the case of ferrite, the carbon was affected by BTR more than the impurity element compared with the austenite. Thus, it has been suggested that the BTR changes due to the solidification segregation of solute elements according to each solidification mode.
- 2 November 2022
- Published by Taylor & Francis in Welding International
- Vol. 36 (11) , 693-704
Influence mechanism of solidification mode on solidification cracking susceptibility of stainless steel
It is well-known that the solidification cracking susceptibility of stainless steel changes depending on the amount of ferrite in the weld metal at room temperature. However, the cause and effect of the amount of ferrite at room temperature and solidification cracking have not always been clarified. When considering the temperature range in which solidification cracks occur, it must be necessary to focus on changes in microstructure and behavior during solidification. In this study, the solidification cracking susceptibility of stainless steel was investigated according to the above reasons, and its susceptibility was summarized using the solidification mode, in other words, an amount of delta ferrite during solidification. A quenched microstructure at the solid–liquid coexistence region was obtained for each stainless steel, and the solidification mode and the amount of the delta ferrite during solidification were investigated. The solidification cracking susceptibility was evaluated using the Trans-Varestraint test, and the effect of solidification mode on the brittle temperature range (BTR) was clarified. In addition, a theoretical study on BTR was conducted, and the effect of solidification mode on solidification segregation at each stainless steel was considered. It was found that the solidification segregation behavior changes depending on the solidification mode. Especially, the effect of solidification and segregation of impurity elements such as sulfur and phosphorus were large in the austenite, in the case of ferrite, the carbon was affected by BTR more than the impurity element compared with the austenite. Thus, it has been suggested that the BTR changes due to the solidification segregation of solute elements according to each solidification mode.
- 11 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 341-349
Interpretation of evaluation indices based on solidification cracking behavior by in situ observation in Trans-Varestraint test
- 11 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 341-349
Interpretation of evaluation indices based on solidification cracking behavior by in situ observation in Trans-Varestraint test
- 10 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 351-362
Relationship between ferrite–austenite phase transformation and precipitation behavior of sigma phase in super duplex stainless steel weldment
- 10 January 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (2) , 351-362
Relationship between ferrite–austenite phase transformation and precipitation behavior of sigma phase in super duplex stainless steel weldment
- Open Access
- 23 June 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (10) , 2013-2021
Quantitative evaluation of augmented strain at the weld metal during the Trans-Varestraint test
The hot cracking susceptibility in the Trans-Varestraint test was evaluated using the nominal strain calculated using the curvature radius of a bending block and the thickness of a specimen based on the theory of material mechanics. The nominal strain was calculated using the material properties at room temperature. Thus, in the Trans-Varestraint test, the non-uniformity of the strain around the weld part due to the temperature distribution is not considered. Therefore, the strain in the Trans-Varestraint test cannot be evaluated correctly. The aim of this study is to reveal the loaded strain at the weld metal to understand the evaluation of hot cracking susceptibility in the Trans-Varestraint test. The loaded strain around the trailing edge of the weld pool of pure iron was measured in-situ using a high-speed camera and high-resolution optical lens. The results of strains measured using image analysis and the finite-element method at the center of the weld bead were compared. Accordingly, it was clarified that the strain was concentrated on the weld part owing to the bending occurring along the weld line, and the strain exceeding the nominal strain was loaded to the trailing edge of the weld pool.
- 23 June 2021
- Published by Springer Nature in Welding in the World
- Vol. 65 (10) , 2013-2021
Open AccessQuantitative evaluation of augmented strain at the weld metal during the Trans-Varestraint test
The hot cracking susceptibility in the Trans-Varestraint test was evaluated using the nominal strain calculated using the curvature radius of a bending block and the thickness of a specimen based on the theory of material mechanics. The nominal strain was calculated using the material properties at room temperature. Thus, in the Trans-Varestraint test, the non-uniformity of the strain around the weld part due to the temperature distribution is not considered. Therefore, the strain in the Trans-Varestraint test cannot be evaluated correctly. The aim of this study is to reveal the loaded strain at the weld metal to understand the evaluation of hot cracking susceptibility in the Trans-Varestraint test. The loaded strain around the trailing edge of the weld pool of pure iron was measured in-situ using a high-speed camera and high-resolution optical lens. The results of strains measured using image analysis and the finite-element method at the center of the weld bead were compared. Accordingly, it was clarified that the strain was concentrated on the weld part owing to the bending occurring along the weld line, and the strain exceeding the nominal strain was loaded to the trailing edge of the weld pool.
- 1 December 2020
- Published by Taylor & Francis in Welding International
- Vol. 34 (10-12) , 405-424
Interpretation and metallurgical modelling of hot ductility curve for solidification cracking
The aim of this study is to discuss and model the hot ductility curve during solidification in the welding from the metallurgical point of view. The contents in this study are as follows: the transverse Varestraint test was conducted to evaluate the solidification cracking; then, the in-situ observation was applied on the Varestraint test in order to obtain the critical strain of solidificationsolidification cracking occurrence. In addition, the U-type hot cracking test was also carried out to obtain the critical strain, and both critical strains were compared. Moreover, the numerical modelling was also performed in order to quantitatively explain the tendency of the relationships between the temperature and the strain. The solidification starting temperature at the non-equilibrium state was estimated based on the K-G-T model. The solidification segregation on the non-equilibrium solidification was calculated based on the mathematical analysis method proposed by T. Matsumiya. In addition, R-D-G model that is firstly suggested by M. Rappaz was used in order to explain the change in the strain depending on the progress in solidification. This paper finally mentioned the possibilities of the prediction of hot ductility curve by numerical simulation.
- 1 December 2020
- Published by Taylor & Francis in Welding International
- Vol. 34 (10-12) , 405-424
Interpretation and metallurgical modelling of hot ductility curve for solidification cracking
The aim of this study is to discuss and model the hot ductility curve during solidification in the welding from the metallurgical point of view. The contents in this study are as follows: the transverse Varestraint test was conducted to evaluate the solidification cracking; then, the in-situ observation was applied on the Varestraint test in order to obtain the critical strain of solidificationsolidification cracking occurrence. In addition, the U-type hot cracking test was also carried out to obtain the critical strain, and both critical strains were compared. Moreover, the numerical modelling was also performed in order to quantitatively explain the tendency of the relationships between the temperature and the strain. The solidification starting temperature at the non-equilibrium state was estimated based on the K-G-T model. The solidification segregation on the non-equilibrium solidification was calculated based on the mathematical analysis method proposed by T. Matsumiya. In addition, R-D-G model that is firstly suggested by M. Rappaz was used in order to explain the change in the strain depending on the progress in solidification. This paper finally mentioned the possibilities of the prediction of hot ductility curve by numerical simulation.
- 1 September 2020
- Published by Elsevier in Materials Today Communications
- Vol. 24, 101094
Suppression of solidification cracking via thermal strain control in multi-beam welding
- 1 September 2020
- Published by Elsevier in Materials Today Communications
- Vol. 24, 101094
Suppression of solidification cracking via thermal strain control in multi-beam welding